TECHMATTE amFilm S21U UV glass screen protector User Guide
- June 5, 2024
- TECHmatte
Table of Contents
Installation Guide
ULTRA
amFilm S21U UV glass screen protector
Q &A
Q: I got an air bubble during installation. What now?
A : If the Screen Protector Is already on the phone with the adhesive
spread, you will need a replacement Protector. Cure the Protector with the UV
light, then remove it and discard it. Please send us an email for a free
replacement.
Q: The Gel didn’t spread evenly during the application, and it’s been
more than 3 minutes. What do I do?
A: Tilt the phone in the direction that the Gel needs to go. DO NOT TOUCH
THE PROTECTOR.
Q: How do I reset my fingerprint after installing the screen protector?
A: Navigate: Settings > Lock screen > Looking for something else? >
Fingerprints > Add Fingerprint
Q: How do I remove the Screen Protector?
A: Once the UV gel is cured, it becomes o solid adhesive gel. You can
peel the screen protector off, starting with one corner and carefully lifting
it up.
Q: The adhesive comes out of the tube, but a small amount splashed into
its own puddle.
A: Tilt the phone so the larger pool will absorb the smaller one, and
then tilt so the adhesive will return to the center. Or, use the adhesive tube
to drag the small puddle into the larger one.
Damaged or Arrived Broken?
Try our 1-Click Warranty Claim
Go to TechMatte.com/WarrantvClaim| Want
More Coverage?
Unlock our Lifetime Warranty
Go to TerhMatte.com/Register 0R| 0R
Scan the QR Code Below.
---|---|---
| |
http://www.techmatte.com/WarrantyClaim|
http://www.techmatte.com/Register|
www.TechMatte.com/install/UV3
1 Turn off your device and apply the leveling pads to the back of your phone.
These will keep the phone from sliding.|
---|---
2 Clean the screen with wet wipes, a cleaning cloth, and dust removal
stickers|
3 Use the Screen-Prep cloth to wipe the surface of the device screen a few
times. Then use the cleaning cloth to clean the screen ac This will help to
prevent the bubbles during application.|
4 Place the application tray on your phone. Make sure to align the side
labeled “top” with the top of the phone. Press firmly into place. Then insert
the pins on each end of the application hay.|
5 Make sure the phone is 100% level by using the included bubble level. Set it
in the middle of the phone’s screen. The bubbles will be centered when the
surface is fiat.|
6 Place absorption pads in the side slots located on the long edges of the
application tray. Re-clean the screen using dust removal stickers if needed.|
Unscrew the RED cap of the first adhesive tube. Hold the tube. over the left
set of pegs on the application tray with the opened end facing down.
Unscrewing the black cap will release the adhesive in the tube.|
8 Drip all the adhesive onto the left side of the screen. Repeat step 7 with
the second adhesive tube. Apply the adhesive to the right side of the phone
screen, aligning the tube with the pegs.|
9 Peel off the mask film of the screen protector, and set it within the tray,
resting it on the pins on either edge of the phone. Make sure the camera
cutout is aligned with the top of the phone, where the device’s front-facing
camera is located.|
10 SLOWLY pull both pins outward to allow the protector to lower onto the
adhesive. Once the protector touches BOTH adhesive puddles, pull the pins out
the rest of the way AT THE SAME TIME.|
11 The adhesive will begin spreading on its own. While it is spreading, place
the metal cylinder on the fingerprint scanner sticker.|
12 Wait for the adhesive to fully spread to all edges of the phone. DO NOT
TOUCH the screen protector during this time|
13 Plug in the UV light with your USBC cable and turn it on. Place the UV
light over the tray and device. Cure for about 45 seconds.|
14 Remove the installation tray, metal cylinder, and scanner sticker.|
15 Use the UV light again to cure for about 60 seconds.|
16 Rescan your fingerprints into the phone system if needed, and enjoy the
screen protector!|
24/7 Customer Support
support@techmatte.com
www.techmatth.com
STAY CONNECTED
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>