ALPHAFIT MKT1024 Core Cable Multi Station Instructions
- June 5, 2024
- ALPHAFIT
Table of Contents
ALPHAFIT MKT1024 Core Cable Multi Station
IMPORTANT – READ FIRST
It is the responsibility of the owner to ensure that all users of this product
are adequately informed of all precautions. The safety and integrity designed
into the equipment can only be maintained when it is regularly examined for
damage and repaired. It is the responsibility of the user/owner to ensure that
regular maintenance is performed. Inspect and properly tighten all parts
regularly. Replace any worn or damaged parts immediately and do not use until
the equipment has been repaired. Both AlphaFit and buyer disclaim any express
or implied warranty, including, without limitation, warranties or
merchantability and/or fitness for a particular purpose with respect to the
equipment.
WARNING: MISUSE OF THIS EQUIPMENT CAN RESULT IN SEVERE INJURY OR DEATH.
BUYER ASSUMES ALL LIABILITY IN USAGE OF EQUIPMENT.
CABLE EQUIPMENT – MAINTENANCE PROCEDURES
CLEAN
Upholstery with mild soap and water or all purpose cleaner. Guide rods with a
dry lint free cloth. For stubborn contamination use IPA 70% or greater. Cable
grips with mild soap and water or all purpose cleaner. Covers and powder
coated surfaces with non -abrasive PH neutral detergent and water, or
recommended solvents.
INSPECT
Machine cables, paying special attention to any hardened spots or distortion
in the cable itself (image 1), as well as cracks or damage to the protective
plastic of the cable (image 2 & 3). Run your hand over the cable to check for
signs of internal distortion, the cable should be uniform and smooth over the
entire length. Cables must always be replaced at the first sign of wear, even
if only the outer rubber protection is worn. Passage of the machine cables
through cams, pulleys and/or the terminals connected to ball joints. Hardware
should be checked for looseness. Tighten as required using metric tools.
Frames should be inspected for wear or damage. Cable grips should be checked
for wear or damage.
DAILY
Wipe down upholstery with mild soap and water or all purpose cleaner. Visually
inspect cables for wear at and around connections and along entire length of
cable. Cables must always be replaced at the first sign of wear.
WEEKLY
Visually inspect all hardware for loosening, tampering or wear. Check jam nut
on weight stack for tightness. Inspect passage of the machine cables through
cams, pulleys and/or the terminals connected to ball joints. Check cables for
stretch and adjust as necessary by loosening the large nut on top of the
weight stack and screw in the threaded plug until the cable has 1015mm of
play and the weight stack pin goes in all holes easily. Tighten the large nut
to complete the adjustment. Note: cables need a minimum of 10mm of play to
account for weight stack bumper compression. Any less can cause damage or
premature wear or failure of the cable.
Check condition of cable grips.
MONTHLY
Clean Guide Rods with a dry lint free cloth using IPA 70% or greater for
stubborn contamination. Clean tops of bearings at stack and inspect for heavy
build-up on rods below head plate (safely lift and secure half of the weight
stack and clean as necessary). Clean covers and powder coated surfaces with
warm water and nonabrasive PH neutral detergent. Surfaces should be thoroughly
rinsed after cleaning to remove all residue.
YEARLY
Inspect the frames for wear or damage.
CABLE EQUIPMENT – MAINTENANCE PROCEDURES
Image 1: Distortion of internal fibers, replace immediately.
Image 2: Crack in protective sheath, replace immediately.
Image 3: Damage to protective sheath, replace immediately.
IMPORTANT DON’TS
Don’t use abrasive or highly alkaline cleaners. Never scrape with harsh
brushes, razor blades or other sharp instruments. Don’t use benzene, gasoline,
acetone or carbon tetrachloride. Don’t clean in hot sun or at elevated
temperatures.
COMPATIBLE CLEANERS FOR POWDER COATING
Isopropyl alcohol (IPA) Methylated spirits
REMOVING INKS, MAKEUP AND STICKERS
Butyl cello solve works to remove ink and makeup stains. Stickers may be
removed using kerosene. If the solvent isn’t working apply gentle heat (hair
dryer) to soften the adhesive.
For additional information, contact Alpha Fit:
1300 257 428
admin@alphafit.com.au
www.alphafit.com.au
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>