Einhell 40.204.15 Cordless Pruning Chain Saw Instructions
- June 4, 2024
- Einhell
Table of Contents
- Einhell 40.204.15 Cordless Pruning Chain Saw
- Product Usage Instructions
- 1. Safety regulations
- Layout and items supplied
- Proper use
- Technical data
- Before starting the equipment
- Assembly and starting
- Cleaning, maintenance and ordering of spare parts
- Disposal and recycling
- Charger indicator
- Possible causes of failure
- Warranty certificate
- Declaration of conformity
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Einhell 40.204.15 Cordless Pruning Chain Saw
Specifications:
- Model: TE-AC 36/150 Li OF
- Operating Instructions Languages: D, GB, F, I, DK, S, NL, SLO, RO, GR, HR, RS, PL, EE
- Art.-Nr.: 40.204.15
- I.-Nr.: 21023
Product Usage Instructions
Safety Instructions:
- Ensure to remove all packaging and transportation protections before use.
- Keep the device out of reach of children and store it in a safe place.
Technical Data :
Refer to the technical specifications provided in the manual for detailed
information.
Pre-Operation Steps:
- Place the compressor on a stable surface in a well-ventilated area.
- Ensure all necessary connections are secure before powering on the device.
Battery Installation:
- Open the battery cover as shown in the diagram and insert the batteries into the slots.
- Check the battery status using the LED indicators provided
Power On/Off:
Switch on the device using the power switch and adjust the pressure
settings as required.
Cleaning and Maintenance:
- Always disconnect the batteries before cleaning or performing maintenance tasks.
- Make sure to depressurize the tank before any cleaning or maintenance work.
Transportation :
Use the provided transport handle for easy portability.
FAQ:
Common Issues:
- Solution: Check and tighten all hose connections.
- Solution: Inspect and replace any leaking quick couplings.
- Solution: Adjust the pressure regulator to the desired level.
Original operating instructions Cordless compressor
Danger!
When using the equipment, a few safety precautions must be observed to avoid
injuries and damage. Please read the complete operating instructions and
safety regulations with due care. Keep this manual in a safe place, so that
the information is available at all times. If you give the equipment to any
other person, hand over these operating instructions and safety regulations as
well. We cannot accept any liability for damage or accidents which arise due
to a failure to follow these instructions and the safety instructions.
Explanation of the symbols used (see Fig. 5)
- Danger! – Read the operating instructions to reduce the risk of inquiry
- Caution! Wear ear-muff s. The impact of noise can cause damage to hearing.
- Beware of electrical voltage!
- Beware of hot parts!
- Warning! The unit will start up automatically without warning if the pressure drops below cut-in pressure!
- Important! Use only batteries which are charged to the same level. Never combine full and half-full batteries.
- PS: Max. operating pressure
Tmax: Max. operating temperature
Tmin: Min. operating temperature
V: Tank capacity
1. Safety regulations
- The corresponding safety information can be found in the enclosed booklet.
- Warning!
- Read all the safety information, instructions, illustrations and technical data provided on or with this power tool. Failure to adhere to the following instructions may result in electric shock, fi re and/or serious injury.
- Keep all the safety information and instructions in a safe place for future use.
- This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
Layout and items supplied
Layout (Fig. 1/2)
- Housing cover
- Pressure tank
- Intake air filter
- Foot
- Quick-lock coupling (regulated compressed air)
- Pressure gauge (for reading the set pressure)
- Pressure regulator
- ON/OFF switch
- Transport handle
- Safety valve
- Drainage cock for condensation water
- Battery pack (not supplied)
- Storage compartment for 8-piece adapter set
- Battery cover
Items supplied
Please check that the article is complete as specified in the scope of
delivery. If parts are missing, please contact our service center or the sales
outlet where you made your purchase at the latest within 5 working days after
purchasing the product and upon presentation of a valid bill of purchase.
Also, refer to the warranty table in the service information at the end of the
operating instructions.
-
Open the packaging and take out the equipment with care.
-
Remove the packaging material and any packaging and/or transportation braces (if available).
-
Check to see if all items are supplied.
-
Inspect the equipment and accessories for transport damage.
-
If possible, please keep the packaging until the end of the guarantee period.
-
Danger!
The equipment and packaging material are not toys. Do not let children play with plastic bags, foils or small parts. There is a danger of swallowing or suff ocating! -
Original operating instructions
-
Safety information
Proper use
- The cordless compressor is designed to generate compressed air for compressed air driven tools.
- The equipment is to be used only for its prescribed purpose. Any other use is deemed to be a case of misuse. The user / operator and not the manufacturer will be liable for any damage or injuries of any kind caused as a result of this.
- Please note that our equipment has not been designed for use in commercial, trade or industrial applications. Our warranty will be voided if the machine is used in commercial, trade or industrial businesses or for equivalent purposes.
Technical data
- Mains voltage ………………………………….. 36 V DC
- Compressor speed min-1: ……………………… 3200
- Operating pressure bar: ……………………….max. 8
- Pressure vessel capacity (in liters): ……………… 6
- Theoretical suction rate l/min.: ………………… 150
- Output (compressed air) at 7 bar: …. 50 liters/min
- Output (compressed air) at 4 bar: …. 70 liters/min
- Sound power level LWA in dB: …………………….. 94
- Uncertainty KWA …………………………………2.23 dB
- Sound pressure level LpA in dB: …………………. 73
- Uncertainty KpA ………………………………….2.23 dB
- Protection type: ……………………………………. IPX0
- Weight of the unit in kg: ………………..approx. 10.5
This equipment is supplied without batteries and without a charger and is
allowed to be used only with lithium-ion batteries and chargers from the Power
X-Change series!
Please note that the equipment’s performance will be limited if it is used
with batteries of type Power X-Change 18V 1.5Ah or Power X-Change 18V 2.0 Ah:
With these batteries the compressor will not reach the final cut-out pressure
of 8 bar. The batteries will switch off before reaching the final pressure (at
approx. 4 bar).
- Danger!
- Noise
- The noise emission values were measured in accordance with EN ISO 3744.
Before starting the equipment
Before you connect the equipment to the power supply make sure that the data on the rating plate are identical to those of the rechargeable battery.
- Check the equipment for damage which may have occurred in transit. Report any damage immediately to the transport company which was used to deliver the compressor.
- Install the compressor in the vicinity of the point of consumption.
- Avoid long air lines.
- Make sure that the intake air is dry and dust-free.
- Do not install the compressor in a damp or wet room.
- The compressor may only be used in suitable rooms (with good ventilation and an ambient temperature from +5 °C to 40 °C). There must be no dust, acids, vapors, explosive gases or inflammable gases in the room.
- The compressor is designed to be used in dry rooms. It is prohibited to use the compressor in areas where work is conducted with sprayed water.
- Operate the equipment only on a firm, level surface.
- Use flexible hoses in order to prevent trans-mitting unacceptable loads to the pipeline system at the connection between the compressor system and the pipeline system.
- It is essential to use separators, traps and drains which process the liquids produced by the compressor before the compressor system is put into operation.
- Supply hoses at pressures above 7 bar should be equipped with a safety cable (e.g. a wire rope).
Charging the battery (Fig. 3)
- Take the battery pack out of the equipment. Do this by pressing the side pushlock buttons.
- Check that your mains voltage is the same as that marked on the rating plate of the battery charger. Insert the power plug of the charger (d) into the socket outlet. The green LED will then begin to fl ash.
- Slot the battery pack (12) onto the battery charger (d).
- In the section entitled „Charger indicator“ you will fi nd a table with an explanation of the LED indicator on the charger.
The battery pack can become a little warm during the charging. This is normal.
If the battery pack fails to charge, check:
- whether there is voltage at the socket outlet
- whether there is good contact at the charging contacts
If the battery pack still fails to charge, send
- the charger
- and the battery pack to our customer service center.
To ensure that items are properly packaged and delivered when you send them to
us, please contact our customer service or the point of sale at which the
equipment was purchased.
When shipping or disposing of batteries and cordless tools, always ensure that
they are packed individually in plastic bags to prevent short circuits and fi
res.
To ensure that the battery pack provides long service, you should take care to
recharge it promptly. You must recharge the battery pack when you notice that
the performance of the device drops. Never allow the battery pack to become
fully discharged. This will cause it to develop a defect.
-
Important!
-
Use only batteries which are charged to the same level. Never combine full and half-full batteries. Always charge the two batteries simultaneously.
-
The equipment‘s operating time depends on the battery with the lower charge level. The two batteries must always be fully charged before use. Close the battery cover by swinging it down, and make sure that it latches in place correctly.
-
Installing the battery (Fig. 1b)
-
Flip up the battery cover (18) as shown in Figure 1b. Slot the two rechargeable batteries (12) into the mounts.
-
Battery capacity indicator (Fig. 4)
-
Press the battery capacity indicator switch (a). The battery capacity indicator (b) will indicate the charge status of the battery by means of 3 LEDs.
-
All 3 LEDs are lit:
-
The battery is fully charged.
-
2 or 1 LED(s) are lit:
-
The battery has an adequate remaining charge.
-
1 LED fl ashes:
-
The battery is empty, recharge the battery.
-
All LEDs blink:
-
The battery temperature is too low. Remove the battery from the equipment, keep it at room temperature for one day. If the fault reoccurs, this means that the rechargeable battery has undergone exhaustive discharge and is defective. Remove the battery from the equipment. Never use or charge a defective battery.
Assembly and starting
- Important!
You must fully assemble the equipment before using it for the first time.
- On/Off switch (Fig. 1a)
- To switch on the equipment, set the On/Off switch (8) to position 1.
- To switch off the equipment, move the On/Off switch (8) to position 0 .
- Setting the pressure (Fig. 1a)
- You can adjust the pressure on the pressure gauge (6) using the pressure regulator (7).
- The set pressure can be drawn from the quick-lock coupling (5).
- Setting the pressure switch The pressure switch is set at the factory.
- Cut-in pressure approx. 6 bar
- Cut-out pressure approx. 8 bar
Cleaning, maintenance and ordering of spare parts
-
Hazard!
Remove the rechargeable batteries before doing any cleaning and maintenance work. -
Warning!
Wait until the compressor has completely cooled down. Risk of burns! -
Warning!
Always depressurize the tank before carrying out any cleaning and maintenance work. -
Warning!
After use, always switch off the equipment immediately and pull out the rechargeable batteries.
Cleaning
- Keep the safety devices free of dirt and dust as far as possible. Wipe the equipment with a clean cloth or blow it with compressed air at low pressure.
- We recommend that you clean the appliance immediately after you use it.
- Clean the appliance regularly with a damp cloth and some soft soap. Do not use cleaning agents or solvents; these may be aggressive to the plastic parts in the appliance. Ensure that no water can get into the interior of the appliance.
- You must disconnect the hose and any spraying tools from the compressor before cleaning. Do not clean the compressor with water, solvents or the like.
Condensed water (Fig. 1)
- Important! To ensure a long service life of the pressure vessel (2), drain off the condensed water by opening the drainage cock (11) each time after using.
- Check the pressure vessel for signs of rust and damage each time before using. Do not use the compressor with a damaged or rusty pressure vessel. If you discover any damage, please contact the customer service workshop.
Safety valve (10)
The safety valve has been set for the highest permitted pressure of the
pressure vessel. It is prohibited to adjust the safety valve or remove its
seal. Actuate the safety valve from time to time to ensure that it works when
required. To do so, open the screw cap of the valve while the tank is under
pressure. Once the screw cap has been fully opened you must pull it to let air
escape through the valve. Then screw the cap fully back in place.
Cleaning the intake filter (3)
The intake fi lter prevents dust and dirt being drawn in. It is essential to
clean this fi lter after at least every 300 hours in operation. A clogged
intake fi lter will decrease the compressor‘s performance dramatically. Open
the halves of the air fi lter housing. Use compressed air at low pressure
(approx. 3 bar) to blow out all the parts of the fi lter and then assemble the
fi lter in reverse order. When cleaning, take adequate precautions against dust
(e.g. use a suitable face mask).
Storage
- Warning!
- Pull out the rechargeable batteries and ventilate the equipment and all connected pneumatic tools. Switch off the compressor and make sure that it is secured in such a way that it cannot be started up again by any unauthorized person.
- Warning!
Store the compressor only in a dry location which is not accessible to unauthorized persons. Always store upright, never tilted!
Transport
- Transport the equipment only by carrying it by the transport handle.
- Protect the equipment against unexpected knocks and vibrations.
Ordering replacement parts:
Please quote the following data when ordering replacement parts:
- Type of machine
- Article number of the machine
- Identification number of the machine
- Replacement part number of the part required For our latest prices and information please go to www.Einhell-Service.com
Disposal and recycling
The equipment is supplied in packaging to prevent it from being damaged in transit. The raw materials in this packaging can be reused or recycled. The equipment and its accessories are made of various types of material, such as metal and plastic. Never place defective equipment in your household refuse. The equipment should be taken to a suitable collection center for proper disposal. If you do not know the whereabouts of such a collection point, you should ask in your local council offices.
Charger indicator
Indicator status | Explanations and actions |
---|---|
Red LED | Green LED |
Off | Flashing |
- Ready for use
- The charger is connected to the mains and is ready for use; there is no battery pack in the charger
On| Off|
- Charging
- The charger is charging the battery pack in quick charge mode. The char- ging times are shown directly on the charger.
- Important! The actual charging times may vary slightly from the stated charging times depending on the existing battery charge.
Off| On| The battery is charged and ready for use. (READY TO GO)
- The unit then changes over to gentle charging mode until the battery is fully charged.
- To do this, leave the rechargeable battery on the charger for approx. 15 minutes longer.
- Action:
- Take the battery pack out of the charger. Disconnect the charger from the mains supply.
Flashing| Off|
- Adapted charging
- The charger is in gentle charging mode.
- For safety reasons the charging is performed less quickly and takes more time. The reasons can be:
- The rechargeable battery has not been used for a very long time.
- The battery temperature is outside the ideal range.
- Action:
- Wait for the charging to be completed; you can still continue to charge the battery pack.
Flashing| Flashing|
- Fault
- Charging is no longer possible. The battery pack is defective.
- Action:
- Never charge a defective battery pack. Take the battery pack out of the charger.
On| On|
- Temperature fault
- The battery pack is too hot (e.g. due to direct sunshine) or too cold (below 0° C).
- Action:
- Remove the battery pack and keep it at room temperature (approx. 20° C) for one day .
Possible causes of failure
Problem | Cause | Solution |
---|---|---|
The compressor does not start. |
- No power supply
- Outside temperature is too low.
- Motor is overheated.
|
- Check the rechargeable batteries
- Never operate with an outside temperature of below +5° C.
- Allow the motor to cool down. If necessary, remedy the cause of the overheating.
The compressor starts but there is no pressure.|
- The non-return valve leaks. ****
- The seals are damaged. ****
- The drainage cock for condensation water has a leak.
|
- Have a service center replace the non-return valve.
- Check the seals and have any damaged seals replaced by a service center.
- Check the drainage cock and replace if necessary.
The compressor starts, pressure is shown on the pressure gauge, but the tools do not start.|
- The hose connections have a leak.
- **** A quick-lock coupling has a leak.
- **** Insufficient pressure set on the pressure regulator.
|
- Check the compressed air hose and tools and replace if necessary.
- Check the quick-lock coupling and replace if necessary.
- Increase the set pressure with the pressure regulator.
Disposal
-
Power tools, rechargeable batteries, accessories and packaging should be sorted for environmentally friendly recycling.
Do not dispose of power tools and batteries/rechargeable batteries into household waste!
Only for EU countries:
According to the Directive 2012/19/EU on waste electrical and electronic equipment and its transposition into national law, power tools that are no longer usable, and, according to the Directive 2006/66/EC, defective or drained batteries must be collected separately and disposed of in an environmentally correct manner.
If disposed incorrectly, waste electrical and electronic equipment may have harmful effects on the environment and human health, due to the potential presence of hazardous substances.
Only for United Kingdom:
According to The Waste Electrical and Electronic Equipment Regulations 2013 (SI 2013/3113) (as amended) and the Waste Batteries and Accumulators Regulations 2009 (SI 2009/890) (as amended), products that are no longer usable must be collected separately and disposed of in an environmentally friendly manner.
The reprinting or reproduction by any other means, in whole or in part, of documentation and papers accompanying products is permitted only with the express consent of the Einhell Germany AG.
Subject to technical changes -
Service information
We have competent service partners in all countries named on the guarantee certifi cate whose contact details can also be found on the guarantee certifi cate. These partners will help you with all service re-quests such as repairs, spare and wearing part orders or the purchase of consumables.
Please note that the following parts of this product are subject to normal or natural wear and that the following parts are therefore also required for use as consumables.
Category | Example |
---|---|
Wear parts* | Battery |
Consumables* | |
Missing parts |
- Not necessarily included in the scope of delivery!
- In the eff ect of defects or faults, please register the problem on the internet at www.Einhell-Service.com. Please ensure that you provide a precise description of the problem and answer the following questions in all cases:• Did the equipment work at all or was it defective from the beginning?
- Did you notice anything (symptom or defect) prior to the failure?
- What malfunction does the equipment have in your opinion (main symptom)?Describe this malfunction.
- Did the equipment work at all or was it defective from the beginning?
- Did you notice anything (symptom or defect) prior to the failure?
- What malfunction does the equipment have in your opinion (main symptom)?Describe this malfunction.
Warranty certificate
Dear Customer,
All of our products undergo strict quality checks to ensure that they reach
you in perfect condition. In the unlikely event that this equipment develops a
fault, please contact our service department at the address shown on this
guarantee card. You can also contact us by telephone using the service number
shown. Please note the following terms under which guarantee claims can be
made:
- These guarantee terms apply solely to consumers, i.e. natural persons, who do not want to use this product in connection with either their commercial or other self-employed activities. These guarantee terms regulate additional guarantee services which the undermentioned manufacturer promises to buyers of its new products in addition to their statutory rights of guarantee. Your statutory rights of guarantee are not affected by this guarantee. Our guarantee is free of charge to you.
- The guarantee services cover only defects due to material or manufacturing faults on the new product which you have bought in the European Union from the undermentioned manufacturer and are limited to either the rectifi cation of said defects or the replacement of the product, whichever we prefer. Please note that only equipment under the brand name “Professional” has been designed for use in commercial, trade or professional applications. For all other products the guarantee is invalidated if the equipment is used within the guarantee period in commercial, trade or industrial applications or for other equivalent activities.
- Our guarantee does not cover:
- Damage to the equipment caused by failure to comply with the installation/assembly instructions or by unprofessional installation; damage caused by failure to comply with the operating instructions (e.g. connection to the wrong mains voltage or current type); damage caused by failure to comply with the maintenance and safety regulations; damage caused by exposing the equipment to abnormal environmental conditions; damage resulting from poor care and maintenance.
- Damage to the equipment caused by misuse or incorrect applications (e.g. overloading the equipment or using non-approved attachments or accessories); damage caused by foreign bodies (e.g. sand, stones, dust, ….) getting inside the equipment. Damage in transit; damage caused by force or external influences (e.g. by dropping the equipment).
- Damage to the equipment or parts of the equipment which is owed to use-related, normal or otherwise natural wear. For example, batteries and battery packs are manufactured with a cycle limit for design-related reasons. Wear is negatively influenced in particular by load demands and charging speeds as well as exposure to heat, cold, vibration and impact.
- The guarantee is valid for a period of 2 years starting from the purchase date of the equipment. Guarantee claims must be submitted before the end of the guarantee period and within two weeks of the defect being noticed. No guarantee claims will be accepted after the end of the guarantee period. The original guarantee period remains applicable to the equipment even if repairs are carried out or parts are replaced. In such cases, the work performed or parts fitted will not result in an extension of the guarantee period, and no new guarantee will become active for the work performed or for any replacement parts fitted. This also applies if on-site service is used.
- To assert your guarantee claim, register the defective equipment at: www.Einhell-Service.com. You will need to provide proof of purchase of the new item of equipment. Equipment returned without such proof or without a rating plate are excluded from the guarantee services because of the lack of traceability. If the defect is covered by our guarantee, then either the item in question will be repaired immediately and retur-ned to you or we will send you a new replacement.
- If you have taken the equipment with you to a different EU country than where you bought it, we will arrange for a local service partner to provide the guarantee services. If you take the equipment outside the EU, the guarantee will not apply.
Of course, we are also happy to offer a chargeable repair service for any
defects which are not covered or no longer covered by the scope of this
guarantee. To take advantage of this service, please send the equipment to our
service address. We draw attention to the restrictions of this guarantee
concerning wear parts, consumables and missing parts as presented in the
service information included in this operating manual.
Warrantor/ Service:
Einhell UK Ltd, Unit 10, 1st Floor, Champion‘s Business Park, Arrowe Brook
Road, Upton, Wirral, CH49 0UQ
Declaration of conformity: We declare conformity in accordance
with the EU directive and standards for article
*Akku-Kompressor TE-AC 36/150 Li OF (Einhell)**
Standard references: EN 62841-1; EN 1012-1; EN IEC 55014-1; EN IEC 55014-2
ISC GmbH · 6 · D-94405 Landau/Isar
- First CE: 2023
- Art.-No.: 40.204.15 I.-No.: 21023 Subject to change without notice
- Archive-File/Record: NAPR031257 Documents registrar: Thomas Fischer Wiesenweg 22, D-94405 Landau/Isar
- GB Cordless compressor
Declaration of conformity
-
We, Einhell UK Ltd
Champions Business Park, First Floor Unit 10, Arrowe Brook Rd, Upton, Wirral CH49 0AB, United Kingdom
declare the conformity to UK standards and legislation was assessed for: -
Cordless Air Compressor TE-AC 36/150 Li OF (Einhell)
Standards: EN 62841-1; EN 1012-1; EN IEC 55014-1; EN IEC 55014-2
- Article Number: 40.204.15 I.-No.: 21023 Subject to change without notice
- Archive-File/Record: NAPR031257 Documents registrar: Thomas Fischer Wiesenweg 22, 94405 Landau/Isar, Germany
References
- Einhell Service
- Einhell Service
- Herramientas de alta calidad para aficionados al bricolaje y la jardinería | Einhell.es
- Strumenti di alta qualità per gli amanti del Fai da Te e del giardinaggio | Einhell.it
- Que Faire de mes Déchets ? Découvrez les solutions pour tous vos déchets et nos conseils pour en produire moins.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>