IKEA HOLMARED Worktop Bamboo Veneer Instruction Manual

IKEA HOLMARED Worktop Bamboo Veneer

Product Information

Specifications

• Worktop surface pre-treated with hard wax oil
• Edges and cut-outs require STOCKARYD wood treatment oil
• 3mm layer of wood on particleboard, sandable

Product Usage Instructions

Before Installation
Treat edges and cut-outs with STOCKARYD wood treatment oil.

After Installation

• Treat the surface when it starts to wear or become dry using STOCKARYD wood treatment oil.
• Sand down the worktop with a 3mm wood layer on the particleboard if needed to remove scratches.
• Areas prone to drying out like edges, sink, and hob areas need frequent treatment.

Frequency of Treatment
Treat 1-2 times as required, based on wood absorbency.

Important Warning
Soak any cloth used with the product in water immediately after use or store it in an airtight container to prevent self-ignition risk.

The worktop surface is pre-treated at the factory with hard wax oil. Due to the nature of the material, treat the edges and cut-outs with STOCKARYD wood treatment oil, before installation.

After installation, treat the surface when it starts to wear or become dry, to ensure that it retains its durability for many years to come. A Worktop with a 3 mm layer of wood on particleboard can be sanded down to remove scratches if needed.
To ensure that the worktop will retain its durable surface for many years to come, treat it with STOCKARYD wood treatment oil when needed.

Areas where the worktop may dry out, such as edges and areas around the sink and hob, require frequent treatment.

Advice for use

Before installation

• Before installation, store the worktop in a room with normal temperature and humidity levels. Do not place the worktop against a warm radiator, or lay it on a cold floor.
• When storing the worktop, stand it on the back edge of its long-side.
• Do not open the plastic package until you are ready to install the worktop.
• Supporting legs are required when an overhang exceeds 25 cm. The maximum distance between these legs should not be more than 80 cm.
• Not suitable for use in wet rooms.
• Only recommended for indoor use.

After installation

• When the worktop’s surface starts to wear or becomes dry, sand the worktop following the direction of the grain.
• Prepare the worktop first by polishing the wood surfaces with fine sandpaper. Wipe away all sawdust with a dry cloth.
• Apply STOCKARYD wood treatment oil onto a soft cloth then wipe over the surface to create a thin, even film.
• Leave to penetrate the surface for approx. 20 minutes.
• Wipe off any unabsorbed oil with a dry, soft cloth.
• Allow the surface to dry and repeat the oil treat¬ment 1-2 times if required, depending on the absorbency of the wood.
• After the first treatment, sand the surface lightly with fine sandpaper. Let the surface dry and repeat the treatment after a few days.

Care and maintenance

• To ensure that the worktop will retain its durable surface for many years to come, treat it with STOCKARYD wood treatment oil when needed.
• Areas where the worktop may dry out, such as around the sink and hob, should be treated often.
• Scratches and small blemishes can be treated with fine sandpaper on a sanding block.
• Always sand in the direction of the grain.
• For daily cleaning, use ordinary washing-up detergent, soap or water. Never use chemicals to clean the worktop.
• Worktops that are installed above a dishwasher, washing machine or oven should be protected on the underside with a FIXA diffusion barrier.
• Always use a chopping board, and never cut directly on the worktop with a knife. Never pull an object with rough or ragged edges across the worktop as it can scratch the surface.
• Do not place a toaster, coffee maker, kettle or other kitchen appliances that emit heat directly over a seam between two worktops because the heat can damage the seam.
• Never use a steel scourer, scourer pad, scouring agent or similar products as they can scratch the surface

WARNING: Soak any used cloth impregnated with this product in water immediately after use, or store in an airtight glass or metal container to prevent the risk of self-ignition.

© Inter IKEA Systems B.V. 2022 AA-2400679-2

FAQ

• Q: How often should I treat the worktop?
  • A: Treat the worktop 1-2 times as needed, depending on the absorbency of the wood.
• Q: Can I sand down the worktop if it gets scratched?
  • A: Yes, if your worktop has a 3mm layer of wood on particleboard, it can be sanded down to remove scratches.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>