lowes 4978229 Uolfin 4 Light Matte Gold Pendant Light Instruction Manual
- June 3, 2024
- lowes
Table of Contents
4978229 Uolfin 4 Light Matte Gold Pendant Light
Instruction Manual
4978229 Uolfin 4 Light Matte Gold Pendant Light
Item Number: 4978229
WARNING (To reduce the risk of fire, electric shock, or personal injury):
-
We suggest installation by a licensed electrician.
-
Please read the instruction carefully and save them as you may need them at a later time.
-
Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
A) Go to the main fuse, or circuit breaker, box in your home.
Place the main power switch in the “OFF” position.
B) Place the wall switch in the “OFF” position. -
The mounting surface should be clean, dry, flat, strong enough, and 1/4” larger than the canopy on all sides.
Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required. -
Make sure that the ceiling or wall can stand the weight of the lamp before installation.
-
Make sure the voltage you are using is 120V. The maximum wattage is 40W per bulb.
-
Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
-
When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
-
The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution, and care must be used with any electrical products.
IMAGE FOR FINISHED PRODUCT:
TOOLS REQUIRED (NOT INCLUDED):
Before starting assembly and installation please prepare the needed tools as below picture
| Ladder
---|---
| Phillips head.flat blade screwdriver
| Electrical tape
| Pliers
| Wire cutter/Stripper
PARTS TYPE & QTY INCLUDING:
(C) Single bar (1)
(D) Green ground screw (1)
(E) Canopy (1)
(F) Collar ring (1)
(G) Collar loop (1)
(H) Quick link (2)
(I) Chain (1)
(J) Loop (1)
(K) Upper frame (1)
(L) Decorative frame (6)
(M) Stem (1)
(N) The lower frame (1)
(O) Screw (12)
(P) Arm (4)
(Q) Arms assembly (1)
ACCESSORIES & QTY ENCLOSED:
(A) Wire connector (3)
(B) Mounting screw (2)
OUTLET BOX
ASSEMBLY & INSTALLATION INSTRUCTIONS:
-
Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
-
Make preinstallation
Step A1: Screw stem (M) onto the top of arms assembly (Q), and adjust arms (P) to the proper position.
Step A2: Attach decorative frames (L) to the upper frame (K) and lower frame (N) with screws (O).
Step A3: Pass the fixture wires through the upper frame (K) and loop (J), then screw loop (J) and stem (M) onto the upper frame (K).
Step B1: By measuring, determine the correct number of links
needed for proper hanging height. Using
the chain pliers, disconnect, and discard the unwanted part.
Step B2: Attach quick link (H) to chain (I) and loop (J) on the top of the upper frame (K).
Step B3: Carefully weave the fixture wires through the chain (I) in and out of every other link and stop just when you reach the top of the chain (I). Gently pull the wires to ensure the wires are not stressed. -
Turn off the power
Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.
A) Go to the main fuse, or circuit breaker, box in your home.
Place the main power switch in the “OFF” position.
B) Place the wall switch in the “OFF” position. -
Make installation
Step C1: Remove collar ring (F) from collar loop (G). Attach single bar (C) to
the outlet box with mounting screws (B).
NOTE: the side of the single bar (C) marked “GND” must face out.
Step C2: Raise canopy (E) over collar loop (G) and screw collar ring (F) to
measure a proper position.
Unscrew collar ring (F) from collar loop (G) and remove canopy (E). Refer to
the following note, you would know the proper position where the collar loop
(G) should be located.
NOTE: canopy (E) should be snug against the ceiling and collar loop (G)
should be screwed with enough threads (no less than 6 threads) on the pre
assembled threaded nipple for more secure hanging. If not, adjust the collar
loop (G) on the single bar assembly (C) by screwing the collar loop (G) in or
out of the single bar (C) until the secure length is achieved.
Step C3: Pass chain (I) through collar ring (F) and then through the canopy
(E).
Step C4: Open quick link (H), and attach quick link (H) to collar loop (G).
Close quick link (H).
Pass the fixture wires through the collar loop (G) to the top of the
preassembled threaded nipple and gently pull to ensure the wires are not
stressed.
Step C5: If needed, shorten the length of the fixture wires. At this point,
the remaining wire length measured above the single bar (C) is at least 6″.
Step C6: Make wire connections
Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS
BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
Connect ground wires according to the below chart
Connect wires according to the below chart
Twist wires together with plastic wire connectors until tightly joined, and
wrap each connector with approved electrical tape. Be sure that no wire
strands are exposed and then carefully tuck all wires into the outlet box.
Step C7: Raise canopy (E) to the ceiling and secure canopy (E) in place by
tightening collar ring (F) onto collar loop (G).
Step C8: Install bulbs (not included) (Please do not exceed the maximum
wattage recommended on the socket.)
5. Check everything is already installed properly, then you could turn on the
light. Enjoy!
CLEANING.
To clean, wipe the fixture with a soft cloth. Do not use abrasive materials such as scouring pads or powders, steel wool, or abrasive paper.
ORDERING PARTS.
Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustrations when ordering parts.
uolfin@newdecorworld.com
+1 850 296 2377
Working hours: Mon Fri 9:00 a.m. 16:00 p.m. EST
uolfin@newdecorworld.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>