NORMAN DIAL01 Remote Control User Manual

NORMAN DIAL01 Remote Control

Product Information

Specifications

• Model: DIAL01
• FCC ID: Q3V-DIAL01
• IC: 28542-DIAL01
• Compliance: FCC Part 15, ICES-003(B) / NMB-003(B)
• Battery: CR2032 3V

FCC Information

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

Unauthorized modifications may void the user’s authority to operate this equipment. To avoid interference, connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment.

IC Information

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

Risk of RF exposure: The equipment complies with FCC/ISED RF exposure limits set forth for an uncontrolled environment. The equipment must not be co- located or operating in conjunction with any other antenna or transmitter.

Product Usage Instructions

Button Overview

• Move Shade to Fully Open
• Setup Best Privacy Control All Channels Stop
• My Favorite Best View
• Shade Channel (There are 5 channels)
• Move Shade to Fully Closed

The function of buttons may vary depending on the shade type, please refer to the OPERATION section for more details.

Replace Battery

1. Step 1: Remove the Color ring.
2. Step 2: Remove the Battery Cover.
3. Step 3: Replace CR2032 3V batteries.
4. Step 4: Put the battery cover and Color ring back.
5. Step 5: Remote lights will illuminate after proper installation.

Channel Button Introduction

When you select a channel (1~5), the selected channel will light up, and you can then operate the shade(s) that are programmed to this channel.

Group Control

When pressing the ALL button, the button will light up and you can then operate all shades that are programmed to the remote at once.

Operation

Bottom Up (Cellular Shade / Roller Shade / Roman
Shade)| Top Down Bottom Up (Cellular Shade)| Fully close for best privacy.
Day & Night (Cellular Shade)| Fully close for best privacy.
Pefect Sheer| Fully close for best privacy.
Best Privacy| Fully close for best privacy.
Top Down Bottom Up (Cellular Shade)| Top Down Bottom Up (Cellular Shade)| Fully open for best view.
Day & Night (Cellular Shade)| Fully open for best view.
Pefect Sheer| Fully open for best view.
Best Privacy| Fully open for best view.
Day & Night (Cellular Shade)| Top Down Bottom Up (Cellular Shade)| Fully open for best view.
Day & Night (Cellular Shade)| Fully open for best view.
Pefect Sheer| Fully open for best view.
Best Privacy| Fully open for best view.
Pefect Sheer| Top Down Bottom Up (Cellular Shade)| Fully open for best view.
Day & Night (Cellular Shade)| Fully open for best view.
Pefect Sheer| Fully open for best view.
Best Privacy| Fully open for best view.
Best Privacy| Top Down Bottom Up (Cellular Shade)| Fully open for best view.
Day & Night (Cellular Shade)| Fully open for best view.
Pefect Sheer| Fully open for best view.
Best Privacy| Fully open for best view.
My Favorite| Top Down Bottom Up (Cellular Shade)| Move to My Favorite pre-set position. Default My Favorite
position: 1/2 of shade height.
Day & Night (Cellular Shade)| Move to My Favorite pre-set position. Default My Favorite
position: 1/2 of shade height.
Pefect Sheer| Move to My Favorite pre-set position. Default My Favorite
position: 1/2 of shade height.
Best Privacy| Move to My Favorite pre-set position. Default My Favorite
position: 1/2 of shade height.

FAQ

Q: What battery does the remote control use?

A: The remote control uses a CR2032 3V battery.

Q: How do I replace the battery in the remote control?

A: To replace the battery, follow these steps:

1. Step 1: Remove the Color ring.
2. Step 2: Remove the Battery Cover.
3. Step 3: Replace CR2032 3V batteries.
4. Step 4: Put the battery cover and Color ring back.
5. Step 5: Remote lights will illuminate after proper installation.

Q: How do I select a channel?

A: To select a channel, press the corresponding channel button (1~5) on the remote control. The selected channel will light up, and you can then operate the shade(s) that are programmed to this channel.

Q: What is the Group Control feature?

A: The Group Control feature allows you to operate all shades that are programmed to the remote control at once. Simply press the ALL button on the remote control to activate this feature.

Q: What are the different lift feature buttons?

A: The lift feature buttons vary depending on the shade type. Please refer to the OPERATION section for a detailed description of the lift feature buttons for each shade type.

PRODUCT SPECIFICATION

1. Model ：DIAL01
2. Dimensions： OD 67.6mm x H 21.2mm
3. Weight (including battery)： 74.5g ± 20g
4. Battery/Voltage： CR2032 3V x 2
5. Radio Frequency： proprietary 2.4 GHz
6. Operation Temperature : 0°C – 50°C / 32°F – 122°F

FCC ID: Q3V-DIAL01
IC: 28542-DIAL01

FCC Information

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation. Unauthorized modifications may void the user’s authority to operate this equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

CAUTION:
Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment.

IC Information
Innovation, Science and Economic Development Canada (ISED) Notices
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

CAN ICES-003(B) / NMB-003(B)

RF Exposure Warning

The equipment complies with FCC/ISED RF exposure limits set forth for an uncontrolled environment.
The equipment must not be co-located or operating in conjunction with any other antenna or transmitter.

BUTTON OVERVIEW

The function of buttons may vary depending on the shade type, please refer to section “OPERATION”.

REPLACE BATTERY

• Step 1: Remove the Color ring.
• Step 2: Remove the Battery Cover.
• Step 3: Replace CR2032 3V batteries.
• Step 4: Put the battery cover and Color ring back.
• Step 5: Remote lights will illuminate after proper installation.

CHANNEL BUTTON INTRODUCTION

SELECT ONE CHANNEL
When you select a channel (1~5), the selected channel will light up, and you can then operate the shade(s) that are programmed to this channel.

GROUP CONTROL

When pressing “ALL” button, the button will light up and you can then operate all shades that are programmed to the remote at once.

OPERATION

PAIRING REMOTE WITH SHADE

Shades are pre-programmed to the designated channel / group according to your order details. If you want to change the pre-setting, please CLEAR pre-setting first (please refer to page 2) , then follow the below steps to set up a new pairing.

IMPORTANT! Please only pair shades with the same lift type to the same channel for optimal operation.

CLEAR PAIRING REMOTE WITH SHADE

SET MY FAVORITE POSITION

Please press “My Favorite” to check the default position setting, if you would like to change My Favorite position, you could follow below procedures.

CAUTION! To avoid an accidental setup with other shades: Please power off other shades first, or pair the designated shade in a separate channel. Then proceed to set up or clear your desired settings.

CLEAR MY FAVORITE POSITION

If you clear My Favorite position, and do not set a new one, My Favorite position will reset back to default position which is 1/2 the length of the shade.

CAUTION! To avoid an accidental setup with other shades: Please power off other shades first, or pair the designated shade in a separate channel. Then proceed to set up or clear your desired settings.

SET UPPER LIMIT

Shades upper limit has been set before shipping out from factory. If you want to change the pre-setting, please CLEAR the upper limit first (please refer to page 6) , then follow below steps to set up new upper limit.

CAUTION! To avoid an accidental setup with other shades: Please power off other shades first, or pair the designated shade in a separate channel. Then proceed to set up or clear your desired settings.

CLEAR UPPER LIMIT

If the upper limit hasn’t been set successfully, the Best View, Best Privacy, and My Favorite function can’t work optimally.

CAUTION! To avoid an accidental setup with other shades: Please power off other shades first, or pair the designated shade in a separate channel. Then proceed to set up or clear your desired settings.

SET LOWER LIMIT

Shades lower limit has been set before shipping out from factory. If you want to change the pre-setting, please CLEAR the lower limit first (please refer to page 8) , then follow below steps to set up new lower limit.

CAUTION! To avoid an accidental setup with other shades: Please power off other shades first, or pair the designated shade in a separate channel. Then proceed to set up or clear your desired settings.

Note: Lower limit for for Perfect Sheer—Shade is fully lowered and vane is fully opened.

CLEAR LOWER LIMIT

If the lower limit hasn’t been set successfully, the Best View, Best Privacy, and My Favorite function can’t work optimally.

CAUTION! To avoid an accidental setup with other shades: Please power off other shades first, or pair the designated shade in a separate channel. Then proceed to set up or clear your desired settings.

SET VANE OPEN POSITION

(ONLY FOR PERFECT SHEER)

Vane open position has been set before shipping out from factory. If you want to change the pre-setting, please CLEAR the vane open position first (please refer to page 10) , then follow below steps to set up vane open position.

CAUTION! To avoid an accidental setup with other shades: Please power off other shades first, or pair the designated shade in a separate channel. Then proceed to set up or clear your desired settings.

CLEAR VANE OPEN POSITION

(ONLY FOR PERFECT SHEER)

CAUTION! To avoid an accidental setup with other shades: Please power off other shades first, or pair the designated shade in a separate channel. Then proceed to set up or clear your desired settings.

COPY REMOTE

Copy all settings from the existing remote to a new remote.

FACTORY RESET FOR COPY REMOTE

CAUTION! By performing FACTORY RESET, your copied remote will be erased. The connection between your existing remote and hub will be disconnected. But you can still use the existing remote to operate the paired shades.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>