FEIT ELECTRIC T36 Plug and Play Linear Lamp Installation Guide
- June 3, 2024
- Feit Electric
Table of Contents
T36 Plug and Play Linear Lamp
Installation Guide
Safety Information
PLEASE READ THESE INSTRUCTIONS AND WARNINGS PRIOR TO INSTALLATION.
THIS LAMP IS INTENDED TO WORK WITH THE EXISTING MAGNETIC AND ELECTRONIC
BALLAST IN YOUR LIGHTING FIXTURE. THIS IS A PLUG-AND-PLAY LAMP, NO ELECTRICAL
MODIFICATIONS ARE NEEDED.
This LED tube is intended to replace fluorescent tube lamps with ANSI
designation F25T8, F25T12, and F30T12 with G13 base.
This product may not be compatible with all ballasts. For more information
about ballast compatibility please visit www.Feit.Com.
-
Follow all safeguards stated in the manual, in addition to normal safety precautions in working with electrical devices. Always follow basic safety precautions to reduce the risk of fire, electric shock and personal injury.
-
WARNING: RISK OF SHOCK: House electric current can cause painful shock or serious injury unless handed properly. For your safety, always remember to:
A. Turn OFF the power supply at the fuse or circuit breaker box before you install the fixture.
B. Ground the fixture to avoid potential electric shock and to ensure reliable starting.
C. Double check all connections to be sure they are tight and correct.
D. Wear rubber sole shoes and work on a sturdy ladder.
E. Do not touch with wet hands.
F. This device is not intended for use with emergency exits or emergency lights.
G. Do not make or alter any open holes in the enclosure of wiring or electrical components during installation. -
This fixture is designed for use in a circuit protected by a fuse or circuit breaker.
It is also designed to be installed in accordance with local electrical codes. If you are unsure about your wiring, consult a qualified electrician or local electrical inspector, and check your local electrical code. -
Avoid looking directly into the LED light.
-
WARNING: RISK OF CUTS: To prevent wiring damage, abrasion or cuts, do not expose wiring to edges of sheet metal or other sharp objects and wear gloves.
-
Account for small parts and destroy packaging material, as these may be hazardous to children.
WARNING: Check the luminaire (fixture) carefully before installing the
lamp. Ensure the electrical lamp holders (sockets) are not damaged and will
make firm contact with the lamp pins.
CAUTION: Risk of fire – If the lamp or luminaire exhibits abnormal
operation (buzzing, flickering, minimal or no light, etc.), immediately turn
off the power and contact us for more information.
CAUTION: Risk of fire – Suitable for damp locations. Do not use dimmers.
Do not touch lamp pins to the metal housing when installing.
WARNING: Do not install this in a pre-heat luminaire (fixture), often
with external starters.
SAVE THESE INSTRUCTIONS
Thank you for your purchase. Questions, comments, or feedback? We’d love to
hear from you.
Visit feit.com/help for support.
We appreciate the trust and confidence you have placed in Feit Electric
through the purchase of this T36 Linear Lamp.
We strive to continually create quality products designed to enhance your
home. Visit us online to see our full line of products available for your home
improvement needs.
Thank you for choosing Feit Electric.
Limited Warranty
This product is warrantied to be free from defects in workmanship and
materials for up to 5 years from the date of purchase.
If the product fails within the warranty period, please contact Feit Electric
at info@feit.com, or visit feit.com/contact-
us for instructions on replacement or refund.
REPLACEMENT OR REFUND IS YOUR SOLE REMEDY. EXCEPT TO THE EXTENT PROHIBITED BY
APPLICABLE LAW, ANY IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE
DURATION OF THIS WARRANTY. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES
IS HEREBY EXPRESSLY EXCLUDED. Some states and provinces do not allow the
exclusion of incidental or consequential damages, so the above limitation or
exclusion may not apply to you. This warranty gives you specific legal rights,
and you may also have other rights which vary from state to state or province
to province.
FCC STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Note: This
equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures: Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver. Connect the
equipment to an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio/TV technician for help. Any changes
or modifications not expressly approved by the manufacturer could void the
user’s authority to operate the equipment.
THIS PRODUCT MAY NOT BE COMPATIBLE WITH ALL BALLASTS.
FOR MORE INFORMATION ABOUT BALLAST COMPATIBILITY PLEASE VISIT
WWW.FEIT.COM.
Supplier’s Declaration of Conformity:
47 CFR $ 2.1077 Compliance Information
Responsible Party: Feit Electric Company
4901 Gregg Road, Pico Rivera, CA 90660, USA
Direct Replacement/Plug & Play Installation (Type A)
-
Turn off the power at the switch and fuse box or circuit breaker.
-
Remove existing fluorescent lamp(s) from the fixture. Replace with Feit Electric T36/830/LEDG2 LED lamp.
-
Turn on the power at the fuse box or circuit breaker and at the switch and enjoy your new Feit Electric LED lamp.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>