makita VC4210L 230V L-Class Vacuum Cleaner Instruction Manual

VC4210L 230V L-Class Vacuum Cleaner
Instruction Manual

|
---|---
|
|
|
|

The function of the resettable circuit breaker
Applicable for models for the Australian market with a resettable circuit breaker

Only connect suitable power tools to the socket outlet on the vacuum cleaner. The power consumption of the power tool must not exceed 1,200 watts.
The socket outlet has a resettable circuit breaker. If the power consumption is too high, the circuit breaker interrupts the circuit. If the circuit breaker has tripped, it needs about  1 minute to cool down before it can be reset.
WARNING! Risk of injury from an automatically starting power tool.
Before resetting the circuit breaker: Make sure that the connected power If the overload problem persists after resetting the circuit breaker several times: Seek professional help  or contact Makita for technical advice.

Safety instructions

 This document contains the safety information relevant to the appliance along with a quick reference guide. Before starting up your machine for the first time, this instruction manual must be read through carefully. Save the instructions for later use.
Attached to the US unit:
Vacuum Cleaner Safety Instructions US include important instructions for fire, electric shock, or injury.
Further support
Further information on the appliance can be found on our website at www.makita.com.
For further queries, please contact the Makita service representative responsible for your country.

Symbols used to mark instructions
DANGER
Danger that leads directly to serious or irreversible injuries, or even death.
WARNING
Danger can lead to serious injuries or even death.
CAUTION
The danger can lead to minor injuries and damage.

Instructions for use
The appliance must:

• only be used by persons, who have been instructed in its correct usage and explicitly commissioned with the task of operating it

• only be operated under supervision This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge.
  Children shall be supervised to make sure that they do not play with the appliance.
  Do not use any unsafe work techniques.
  Never use the appliance without a filter.
  Switch off the appliance and disconnect the mains plug in the following situations:

• Prior to cleaning and servicing

• Prior to replacing components

• Prior to changing over the appliance

• If foam develops or liquid emerges

Besides the operating instructions and the binding accident prevention regulations valid in the country of use, observe recognised regulations for safety and proper use.
Before starting work, the operating staff must be informed on and trained within:

• use of the machine
• risks associated with the material to be picked up
• safe disposal of the picked up material

Purpose and intended use
This mobile dust extractor is designed, developed and rigorously tested to function efficiently and safely when properly maintained and used in accordance with the following instructions.
This machine is suitable for industrial use, such as e.g. plants, construction sites and workshops.
This machine is also intended for commercial use, for example in hotels, schools, hospitals, factories, shops, offices and rental businesses.
Accidents due to misuse can only be prevented by those using the machine.
READ AND FOLLOW ALL SAFETY INSTRUCTIONS.

The appliance is suitable for picking up dry, nonflammable dust and liquids.
Any other use is considered improper use.
The manufacturer accepts no liability for any damage resulting from such use.
The risk for such use is borne solely by the user. Proper use also includes proper operation, servicing, and repairs as specified by the manufacturer.
The appliance is suitable for picking up dry, nonflammable dust and liquids, and hazardous dust with OEL (Occupational Exposure Limit) value > 1mg/m³.
Dust Class L (IEC 60335-2-69).

For machines intended for the Dust Class L, the filter material is tested. The maximum degree of permeability is 1% and there is no special requirement for disposal.
For dust extractors, ensure adequate air change rate, when the exhaust air is returned to the room.
Observe national regulations before use.

Electrical connection
It is recommended that the machine should be connected via a residual current circuit breaker.

Arrange the electrical parts (sockets, plugs and couplings) and lay down the extension lead so that the protection class is maintained.
Connectors and couplings of power supply cords and extension leads must be watertight.

Extension lead
As an extension lead, only use the version specified by the manufacturer or one of a higher quality.
When using an extension lead, check the minimum cross-sections of the cable:

Guarantee
Our general conditions of business are applicable with regard to the guarantee.
Unauthorized modifications to the appliance, the use of incorrect brushes in addition to using the appliance in a way other than for the intended purpose exempt the manufacturer from any liability for the resulting damage.
Important warnings

WARNING
To reduce the risk of fire, electric shock, or injury, please read and follow all
safety instructions and caution markings before use. This machine is designed to be safe when used for cleaning functions as specified. Should damage occur to electrical or mechanical parts, the machine and/or accessory should be repaired by a competent service center or the manufacturer before use in order to avoid further damage to the machine or physical injury to the user.

Do not leave the machine when it is plugged in. Unplug from the socket when not in use and before maintenance.
Outdoor use of the appliance shall be limited to occasional use.
Do not use with a damaged cord or plug. To unplug grasp the plug, not the cord. Do not handle plug or machine with wet hands.
Turn off all controls before unplugging.
Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. Do not run the machine over the cord.
Keep cord away from heated surfaces.
Keep hair, loose clothing, fingers, and all parts of the body away from openings and moving parts. Do not put any objects into openings or use them with the opening blocked. Keep openings free of dust, lint, hair, and anything else that could reduce the flow of air.
Do not use in outside areas at low temperature.
Do not use to pick up flammable or combustible liquids such as gasoline, or use it in areas where they may be present.
Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
Use extra care when cleaning on stairs.
Do not use unless filters are fitted.
If the machine is not working properly or has been dropped, damaged, left outdoors, or dropped into water, return it to a service center or dealer.
If foam or liquid escapes from the machine, switch it off immediately.
The machine may not be used as a water pump. The machine is intended for vacuuming air and water mixtures.
Connect the machine to a properly earthed mains supply.
The socket outlet and the extension cable must have an operative protective conductor.
Provide for good ventilation at the working place.
Do not use the machine as a ladder or step ladder. The machine can tip over and become damaged. The danger of injury.
Only use the socket outlet on the machine for purposes specified in the instructions.

Risks

Electrical components
DANGER
The upper section of the machine contains live components.
Contact with live components leads to serious or even fatal injuries.

1. Never spray water onto the upper section of the machine.

Electric shock due to faulty mains connecting lead.
Touching faulty mains connecting lead can result in serious or even fatal injuries.

1. Do not damage the mains power lead (e.g. by driving over it, pulling, or crushing it).
2. Regularly check whether the power cord is damaged or shows signs of aging.
3. If the electric cable is damaged, it must be replaced by an authorized Makita distributor or similarly qualified person in order to avoid a hazard.
4. In no circumstances should the power supply cord be wrapped around fingers or any part of the operator’s person.

Hazardous dust
WARNING
Hazardous materials.
Vacuuming hazardous materials can lead to serious or even fatal injuries.

1. The following materials must not be picked up by the machine:
   – hot materials (burning cig- cigarettes, hot ash, etc.)
   – flammable, explosive, aggressive liquids (e.g. petrol, solvents, acids, alkalis, etc.)
   – flammable, explosive dust (e.g. magnesium or aluminum dust, etc.)

Spare parts and accessories
CAUTION
Spare parts and accessories.
The use of non-genuine spare parts, brushes, and accessories can impair the safety and or function of the appliance.

1. Only use original spare parts and accessories from Makita. Spare parts that can affect the health and safety of the operator and or function of the appliance, are specified below:

In an explosive or inflammable atmosphere
CAUTION
This machine is not suitable for use in explosive or inflammable atmospheres or where such atmospheres are likely to be produced by the presence of volatile liquid or inflammable gas or vapor.
*) Optional accessories/Options depending on model Original instruction

Control /Operation

CAUTION
Damage due to unsuitable mains voltage.
The appliance can be damaged as a result of being connected to an unsuitable mains voltage.

1. Ensure that the voltage shown on the rating plate corresponds to the voltage of the local mains power supply.

Starting and operating the machine

1. Check that the electrical switch is switched off (in position 0).
2. Check that suitable filters are installed in the machine.
3. Connect the suction hose into the suction inlet at the machine by pushing the hose forward until it fits firmly in place at the inlet.
4. Connect the tubes with the hose handle, and twist the tubes in order to ensure that they are prop- early fitted.
5. Attach a suitable nozzle to the tube. Choose nozzle depending on what type of material is to be picked up.
6. If used for dust extraction in connection with the dust-producing tool then connect the end of suction hose with the appropriate adapter.
7. Connect the plug to a proper electrical outlet.
8. Put the electrical switch into position I in order to start the motor.

| Turn I:
Activate the machine
---|---
Turn /0:
Stop the machine. Permanent power on socket
Turn AUTO :
Activate Auto-On/Off operation
Turn l+ :
Activate the machine with
deactivated automatic filter cleaning function
Turn AUTO + :
Activate Auto- On/Off operation
with deactivated automatic filter cleaning function
| Suction power control operation on separate turning knob

Auto-On/Off socket outlet for power tools

CAUTION
Appliance socket.
The appliance socket is designed for electrical auxiliary equipment; see technical data for reference.

1. Prior to plugging in an appliance, always switch off the machine and the appliance that is to be connected.
2. Read the operating instructions for the appliance to be connected and observe the safety notes contained in these.

An appliance socket with earthing contact is integrated into the machine.
An external power tool can be connected there. The socket features permanent power when the electrical switch is in position , i.e. the machine can be used as an extension cord.
In position AUTO the machine can be switched on and off by the power tool connected. Dirt is picked up from the source of dust immediately. To comply with regulations,  only approved dust-producing tools should be connected.
The maximum power consumption of the connected electrical appliance is stated in section “Specifications”.
Before turning the switch to position AUTO ensure that the tool connected to the appliance socket is switched off.

AutoClean
The machine is equipped with an automatic filter cleaning system, AutoClean. A frequent cleaning cycle will automatically run during operation to ensure that suction performance is always at its best.
If suction performance decreases or in extensive dust applications a manual filter cleaning operation is recommended:

1. Switch off the machine.
2. Close the nozzles or suction hose opening with the palm of your hand.
3. Turn the switch to position „I“ and let the machine operate at full speed for approx. 10 seconds with the suction hose opening closed.
   If suction power is still reduced take out the filter and clean it mechanically or replace the filter.
   For certain applications, like wet pick up, it is recommended to turn off the automatic filter cleaning system. For details see chapter 3.1.

Antistatic connection *)
CAUTION
The machine is equipped with an antistatic system to discharge any static electricity that may develop during dust pick-up.
The antistatic system is placed in the front part of the motor top and creates an earth-ground connection to the inlet fitting of the container.
For proper function, the use of an electrically conductive or antistatic suction hose is recommended.

1. When inserting the optional disposal bag make sure the antistatic connection is kept.

Cooling air filter
To protect the electronics and motor, the machine is equipped with a cooling air diffusor. Clean the cooling air diffuser regularly.
For areas with a high concentration of fine dust in the surrounding air it is recommended to equip the machine with an optional cooling air filter cartridge to prevent dust from settling inside the air channels and motor. Contact your local sales representative.

CAUTION
If the cooling air filter is clogged by dust the over-load protection switch in the motor can be activated.

1. In such case switch off the machine, clean the cooling air filter, and allow the machine to cool for approx. 5 minutes.

Wet pick-up
CAUTION
The machine is equipped with a water level limit system which shuts off the machine when the maximum liquid level is reached.

1. When this occurs, switch off the machine.
2. Disconnect the machine from the socket and empty the container.
3. Never pick up liquids without the water level limit system and filter in place.
4. Do not pick up flammable liquids.
5. Before liquids are picked up, always remove the filter bag/wastebag and check that the water level limit works properly.
6. If foam appears, stop work immediately and emty the tank.
7. Clean the water level limiting device regularly and check for signs of damage.

Before emptying the container, unplug the machine.
Disconnect the hose from the inlet by pulling out the hose. Release the latches by pulling them outwards so that the motor top is released. Lift up the motor top from the container.  Always empty and clean the container and water level limit system after picking-up liquids.
Empty by tilting the container backward or sideways and pouring the liquids into a floor drain or similar.
Put back the motor top to the container. Secure the motor top with the latches.
Heavy maneuvers can, by mistake, trigger the water level limiting device. Should this happen; turn off the machine and wait for 3 seconds to reset the device.
Continue to operate the machine afterward.

Dry pick-up
CAUTION
Picking up environmentally hazardous materials.
Materials picked up can present a hazard to the environment.

1. Dispose of the dirt in accordance with legal regulations.
   Remove the electrical plug from the socket before emptying after dry pick-up. Release the latches by pulling them outwards so that the motor top is released. Lift up the motor top from the container.
   Filter: Check the filters. To clean the filter you can shake, brush or wash it. Wait until the filter is dry before re-starting dust pick-up.
   Dust bag: check the bag to ensure the fill factor. Replace the dust bag if necessary. Remove the old bag.

The new bag is fitted by passing the cardboard piece with the rubber membrane through the vacuum inlet.
Make sure that the rubber membrane is passing past the heightening at the vacuum inlet.
After emptying: close the motor top to the container and secure the motor top with the latches. Never pick up dry material without a filter fitted in the machine.
The suction efficiency of the machine depends on the size and quality of the filter and dust bag.
Therefore – use only the Original filter and dust bags.

After using the machine

After use
Remove the plug from the socket when machine is not in use. Wind up the cord starting from the machine.
The power cord can be wound up around the motor top or at the container or placed in the included hook, or fastening means. Some variants have special storage places for accessories.

Transport

1. Before transporting the machine, close all the latches.
2. Do not tilt the machine if there are liquids in the dirt tank.
3. Do not use a crane hook to lift the machine.
4. Do not lift the machine by the trolley handle) or the handle of the MAKPAC-Box )

Storage
Store the appliance in a dry place, protected from rain and frost. The machine shall be stored indoors only. Wet filters and the interior part of the liquid container shall be dried before storage.

Accessory and tool storage
For convenient transport and storage of accessories or tools, integrated rails are found on side of the machine which allows fastening with straps or other means.
A flexible strap and hooks are included on the back of the machine for attachment of a suction hose or mains cable. For instruction see the quick reference guide.
An optional adapter plate*) with attachment system can be installed on top of the machine for fastening of 2-point or 4-point storage cases.
Remove the electrical plug from the socket before installing the adapter plate.

*CAUTION)**
Do not lift machine in adapter plate without having storage case safely installed. Note the weight and balance of the appliance in case of storage. The maximum weight of storage cases is 30 kg.

Recycling the machine
Make the old machine unusable.

1. Unplug the machine.
2. Cut the power cord.
3. Do not discard electrical appliances with household waste.
   Due to the presence of hazardous components in the equipment, used electrical and electronic equipment may have a negative impact on the environment and human health.
   Do not dispose of electrical and electronic appliances with household waste!
   In accordance with the European Directive on waste electrical and electronic equipment and its adaptation to national law, used electrical and electronic equipment should be collected separately and delivered to a separate collection point for municipal waste, operating in accordance with the environmental protection regulations.

This is indicated by the symbol of the crossed-out wheeled bin placed on the equipment.

Maintenance

Regular servicing and inspection
Regular servicing and inspection of your machine must be carried out by suitably qualified personnel in accordance with relevant legislation and regulations.
In particular, electrical tests for earth continuity, insulation resistance, and condition of the flexible cord should be checked frequently.
In the event of any defect, the machine MUST be withdrawn from service, completely checked and repaired by an authorized service technician.
At least once a year, a Makita technician or an instructed person must perform a technical inspection including filters, air tightness and control mechanisms.

Maintenance
Remove the plug from the socket before performing maintenance. Before using the machine make sure that the frequency and voltage shown on the rating plate correspond with the mains voltage.
The machine is designed for continuous heavy work. Depending on the number of running hours – the dust filter should be renewed. Keep the machine clean with a dry cloth,  and a small amount of spray polish.

During maintenance and cleaning, handle the machine in such a manner that there is no danger for maintenance staff or other persons.
In the maintenance area:

• Use filtered compulsory ventilation

• Wear protective clothing

• Clean the maintenance area so that no harmful substances get into the surroundings
  During maintenance and repair work all contaminated parts that could not be cleaned satisfactorily must be:

• Packed in well-sealed bags

• Disposed of in a manner that complies with valid regulations for such waste removal.

For details of after-sales service contact your dealer or Makita service representative responsible for your country. See reverse of this document.

Further information

EC Declaration of conformity
For European countries only:
We hereby declare that the machine described below complies with the relevant basic safety and health requirements of the EU Directives, both in its basic design and construction as well as in the version put into circulation by us. This declaration shall cease to be valid if the machine is modified without our prior approval.
Product: Wet and dry vacuum cleaner
Type: VC4210L
Relevant EU Directives:
2006/42/EC, 2014/30/EU, 2011/65/EU
Applied harmonized standards:
EN 60335-1:2012+A11:2014+A13:2017
EN 60335-2-69:2012
EN 55014-1:2017
EN 55014-2:2015
EN IEC 61000-3-2:2019
EN 61000-3-3:2013+A1:2019
EN IEC 63000:2018
Authorized Documentation Representative: Makita Europe N.V., Jan-Baptist Vinkstraat 2, 3070 Kortenberg, Belgium |

01.07.2020
Hiroshi Tsujimura
Director – Makita Europe N.V.
Makita Europe N.V., Jan-Baptist Vinkstraat 2,
3070 Kortenberg, Belgium

UK Declaration of conformity
For UK only:
We hereby declare that the machine described below complies with the relevant basic safety and health requirements of the UK Regulations, both in its basic design and construction as well as in the version put into circulation by us. This declaration shall cease to be valid if the machine is modified without our prior approval.
Product: Wet and dry vacuum cleaner
Type: VC4210L
Relevant UK Regulations:
S.I. 2008/1597 (as amended), S.I. 2016/1091 (as
amended), S.I. 2012/3032 (as amended)
Applied Designated standards:
EN 60335-1:2012+A11:2014+A13:2017
EN 60335-2-69:2012
EN 55014-1:2017
EN 55014-2:2015
EN IEC 61000-3-2:2019
EN 61000-3-3:2013+A1:2019
EN IEC 63000:2018
Authorized Documentation Representative:
Makita Europe N.V., Jan-Baptist Vinkstraat 2,
3070 Kortenberg, Belgium
01.07.2020
Hiroshi Tsujimura
Director – Makita Europe N.V.
Makita Europe N.V., Jan-Baptist Vinkstraat 2,
3070 Kortenberg, Belgium

Importer: Makita (UK) Limited, Michigan Drive,
Tongwell, Milton Keynes, Buckinghamshire,
MK15 8JD, UK

Specifications

• measured at turbine
  Specifications and details are subject to change without prior notice.

Makita Europe N.V. Jan-Baptist Vinkstraat 2,
3070 Kortenberg, Belgium
Makita Corporation 3-11-8, Sumiyoshi-cho,
Anjo, Aichi, 446-8502 Japan
www.makita.com

References

• MAKITA Industrial Power Tools - The Leader In Cordless with 18V LXT Lithium-Ion

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>