Voyager VOM73MMT 7″ COLOR TFT LCD 3 CAMERA SPLIT MIRROR MONITOR Owner’s Manual

June 4, 2024
Voyager

Voyager VOM73MMT 7″ COLOR TFT LCD 3 CAMERA SPLIT MIRROR MONITOR Owner’s Manual

VOM73MMT Features

  • High Performance Automotive Grade 7″ Color LCD Panel
  • 3 Camera Inputs with Split Display
  • Mechanical Button
  • Built-In Audio Speaker
  • Compatible with Voyager Standard Camera

Camera-Monitor Warnings!

  1.  Camera/monitor system aids in the use of, but does not replace vehicle side/rear-view mirrors.
  2. Objects in camera/monitor view are closer than they appear. When backing up, proceed cautiously and be prepared to stop.

Important! – Please Read This Manual Before Installing!

Congratulations on your purchase of a Voyager VOM73MMT LCD Observation Monitor. With proper installation and use, your VOM73MMT LCD is designed to provide you with years of trouble-free operation. Please read this manual thoroughly before beginning.
All Voyager Observation products are strictly intended to be installed as supplement aid to standard rear-view mirror systems that may already exist in your vehicle. Voyager Observation products are not intended for use as substitutes for-view mirror devices, or for any other standard motor vehicle equipment required to be installed on vehicles by law.

While Voyager observation products contribute to improving the vehicle operator’s field of view, these products are no substitute for proper defensive driving techniques and observance of traffic laws and motor vehicle safety regulations.

Warnings!
RED POWER WIRE MUST BE CONNECTED TO ACCESSORY TO AVOID CURRENT DRAW IN THE KEY OFF POSITION.

Installation Location

It is unlawful in most jurisdictions for a person to drive a motor vehicle equipped with a television viewer or screen located at any point forward of the back of the driver’s seat or in any location that is visible, directly or indirectly, to the driver while operating the vehicle. The vom73mmT product is designed to be used primarily as a rear observation device in conjunction with closed circuit camera. In any installations where the VOM73MMT is used to display television broadcasts or recorded video, playback, installation location must adhere to local laws and regulations.

Tampering

To prevent electrical shock, DO NOT OPEN THE MONITOR CASE. There are potentially harmful voltages inside the monitor. If evidence of tampering is detected, the warranty will be considered void and all parts will be non serviceable. There are no user serviceable parts inside the warranty will be considered void.

Moisture

While it will withstand short periods of exposure to moisture, this product does contain sensitive electronic components and exposure should be limited by the user/installer. This product is not designed for locations where constant exposure to moisture or immersion can be encountered. This unit should NEVER be cleaned with a power washer or used where direct power washer spray may be encountered.

Depth of view

OBJECT  VIEWED MONITOR ARE CLOSER THAN APPEAR.

PACKING CONTENTS

  • LCD MONITOR QTY.1
    PACKING CONTENTS

  • CABLE QTY.1
    PACKING CONTENTS

  • METAL BRACKET QTY.1

  • MACHINE SCREW QTY.4 (M3X7mm)

CONTROLS AND OPERATION

Product Controls

  1. POWER ON/OFF

    • Press once to turn on unit
    • Press again to turn off unit
  2. **MENU

Primary Function Enter System Menu
**

  * Press ‘MENU button to enter the System Menu  

Secondary Function Return to previous menu

  * While in menu modes, the ‘MENU’ button is used to return to previous menu.  

Third Function: AUTO SCAN function

  * Press the ‘MENU’ button for 3 seconds to achieve the auto scan function.
  1. **SELECT

Primary Funtion Input Source Select
**

  * Press to switch camera channels, switch order as below:  

Primary Function
Secondary Function Menu Option Selection

  * While in menu mode, the ‘SELECT’ button is used to select the highlighted function or option setting.
  1. & 5 1 UP/DOWN

    Primary Function

    • Pressing ‘UP’ button increase brightness, contrast, color, tint, volume or sleep.
    • Pressing ‘DOWN’ button decrease brightness, contrast, color, tint, volume or sleep.
      Secondary Function
      While in menu modes, the `UP’ DOWN’ are used to select the option setting.

Menu Instruction
Menu Instruction Menu
Instruction
Menu Instruction

Installation Instructions

BEFORE YOU BEGIN INSTALLATION:

Before drilling be sure that no cable or wiring is on the other side. Clamp all wires securely to reduce the possibility of them being damaged during installation and use. Keep all cables away from hot or moving parts, and electrically noisy components.

Wiring Definitions:

  • Power connection:
    Pin 1 POWER IN DC (12V)-Red Pin
    2 GROUND -Black Pin
    3 CHANNEL 1 TRIGGER -Blue Pin
    4 CHANNEL 2 TRIGGER -Brown Pin
    5 CHANNEL 3 TRIGGER -Green

  • Camera 1 input:
    4-Pin Connection for camera or camera extension cable

  • Camera 2 input:
    4-Pin Connection for camera or camera extension cable

  • Camera 3 input:
    4-Pin Connection for camera or camera extension cable

  • LCD panel: General:
    13-Pin Large DIN cable connection to monitor

General:

  1. Choose the monitor and camera locations.
  2. Install all required cables in vehicle. A 3/4″(19mm) hole should be drilled for passing camera cables through vehicle wall , barriers, etc. Install split grommets where applicable. If additional cable protection is required install convoluted tubing over the cable.
  3. After cable/wiring has been routed and components in place, temporarily make all system connections and perform a system function check. If system does not operate properly, see the troubleshooting section regarding cable.
  4. Make sure all cables are routed away from hot or moving parts, and away from sharp edges. Secure cables with wire ties.

Backup (Rear) Camera

  • Rear-mounted camera used for monitoring while backing up must be connected to the CAMi input.Triggerl must be connected to the reverse gear light circuit.

Side Camera

  • The side mounted camera should be connected to the CAM2 and CAM3 inputs. Trigger lines 2 and 3 should be connected to the vehicle’s turn signal circuits.

TYPICAL SYSTEM CONNECTION

SYSTEM CONNECTION

POWER/TRIGGERWIRE FUNCTIONS

REF # WIRE COLOR DESCRIPTION
1 RED POWER IN 12VDC
2 BLACK GROUND
3 BLUE TRIGGERI (CAM1)
4 BROWN TRIGGER2 (CAM2)
5 GREEN TRIGGERI (CAM3)

PRODUCT STRUCTURE

LCD PANEL SPECIFICATIONS

Size/Type 7″(Digital) TFT LCD
Brightness 400 cdirre (typ)
Contrast Ratio 500
View Angles Top (12 O’clock)
(@CR≥10 ) Bottom (6 O’clock)
Horizontal 60″ (typ)
Response Time 15ms

20ms
Back Light Type| LED
Back Light Life| 50,000 hrs (min)

  • Operation Temperature Range: -20° C 70° C

  • Storage Temperature Range: -30° C –80° C

  • Max Humidity: 85%

  • Operation Voltage Range: 12VDC

  • Current Draw (typical): 337mA©12VDC

  • Signal system: NTSC or PAL (Auto detection)

  • Video Aspect Ratio: 16 : 9
    Input Level: 1Vp-p 750

  • Audio Input Level: 150mV(Max)

  • Product Dimensions: 10.04W x 4.72H x 1.24D (Inches)

  • Product Weight: 2.65 Ibs/1200g

Logo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals