Voyager VAVSMOD2 360 Camera System User Manual

June 4, 2024
Voyager

Voyager LOGO 2Voyager LOGO VAVSMOD2
Voyager 360 Camera System
User ManualVoyager VAVSMOD2 360 Camera System Version 1.2

Content List

Item Description QTY
A ECU (electronic control unit/module) with Harness 1
B User Manual 1

Voyager VAVSMOD2 360 Camera System - FIG 1

Additional Products Required (Sold Separately)

Compatible Camera

Item Part Number Description QTY
C VAVSCAM2 Camera and camera hardware 1

*NOTE: 4x VAVSCAM2 required for full system
Calibration Tools

Voyager VAVSMOD2 360 Camera System - FIG 2

System Connections

Voyager VAVSMOD2 360 Camera System - FIG 3

 Camera Installation and Calibration Layout with Small Mat

4.1 Mat Dimension

4.2 Camera Installation Front and Rear View
The camera is recommended to be mounted at the center (A≅B, C≅D ), and the tolerance between C and D could be as much as +/- 30 cm if the Camera is mounted on the Roof.

Voyager VAVSMOD2 360 Camera System - FIG 5

4.3 Camera Installation Side View
The camera is recommended to be mounted at the center (E≅F), and the tolerance could be as much as +/- 30 cm.

Voyager VAVSMOD2 360 Camera System - FIG 6

4.4 Calibration Layout Top View

Voyager VAVSMOD2 360 Camera System - FIG 7

Camera Installation and Calibration Layout with Large Mat

5.1 Mat Dimension

5.2 Camera Installation Front and Rear View
The camera is recommended to be mounted at the center (A≅B, C≅D ), and the tolerance between C and D could be as much as +/- 30 cm if the Camera is mounted on the Roof.

Voyager VAVSMOD2 360 Camera System - FIG 9

5.3 Camera installation Side View
The camera is recommended to be mounted at the center (E≅F), and the tolerance could be as much as +/- 30 cm.

Voyager VAVSMOD2 360 Camera System - FIG 10

5.4 Calibration Layout Top View

Voyager VAVSMOD2 360 Camera System - FIG 11

Auto Calibration

  1. Plug the IR receiver into the connecter labeled IR of ECU

  2. If a new calibration layout, new SKU, or new Vehicle Image deployment is needed, plug the USB Disk into the connector labeled USB of ECU,

  3. Use the Remote Control to process the Auto/ Manual Calibration

  4. Press 02580258 on the Remote Control for Auto Calibration with Camera Check View.
    NOTE: As each button is pressed, you should see a red asterisk (*) appear on the screen indicating the button press was received by the ECU module. Once eight asterisks (****) are shown on the screen, the unit will enter the calibration process.

  5. Calibration Layout Information Check View

  6. Camera Check View

Voyager VAVSMOD2 360 Camera System - FIG 14

6.1 SKU, Layout, and Mat Selection

  1. In Calibration Layout Information Check View, press◄ the key and hold to proceed with SKU, Layout, and Mat size selection with remote control

  2. Move the cursor to SKU and press OK to enter SKU change mode
    – Press ▲▼ to select the preferred SKU
    – Press OK to confirm the change

  3. Move the cursor to the target parameter and press OK to enter the parameter change mode
    – Available parameters are Range of View/ Distance between mats/ Setback setting/ Mat size
    – Press ▲▼ to select a preferred value
    – Press OK to confirm the change

  4. Move the cursor to NEXT and press OK to proceed with the camera check view

Voyager VAVSMOD2 360 Camera System - FIG 15

6.2 Auto Calibration Flow

  1. Press 02580258 on the Remote to access Auto-calibration with Layout/Camera Check ViewVoyager VAVSMOD2 360 Camera System - FIG 16
  2. Press 85208520 on the Remote to access Auto-calibration without Layout/Camera CheckVoyager VAVSMOD2 360 Camera System - FIG 17

Manual Calibration

When the system failed to complete the auto calibration, it will lead to manual calibration.
(However, it is recommended to find the obstruction which caused the failure and remove it from the layout area. Then reattempt the auto-calibration process.)
Manual Calibration Process:

  1. Use the numerical keys (0-7) on the remote to choose the critical spot which is NOT in the correct location.
  2. Use the cursor (▲▼◄►) to move the critical spot to the correct location and check the zoom-in window to confirm.
  3. Use “MENU” key to switch cameras and inner/outer critical spot views

The Correct Locations of each outer critical spot

The Correct Locations of each inner critical spot

7.1 Manual Calibration Flow

  1. Use the numerical keys on the remote to choose the critical spot which is NOT in the correct location. (in this case #3)
  2. Use the Remote cursor (▲▼◄►) to move the cursor to the correct location. (The Zoom-in window at the top helps with accuracy)
  3. Once finished with the adjustments, Press the “MENU” key to switch to the inner 8 critical spots of the same camera and repeat the adjustment, if needed.
  4. When step 3 is finished, the Remote the “MENU” key to switch to the next camera and repeat steps 1, 2, and 3.
  5. When all four cameras are checked (Front -> Rear-> Left-> Right -> Front), Press “OK” to complete manual calibration setup. The system will reset and process the calibration.

Voyager VAVSMOD2 360 Camera System - FIG 21

Trigger Views

If the vehicle is driving forward without turn signals triggered, the VAVSMOD2 will give the driver a top view and Rear view

Voyager VAVSMOD2 360 Camera System - FIG 22

If the Left Turn Signal is triggered, the VAVSMOD2 will give the driver a top view and left-side view

Voyager VAVSMOD2 360 Camera System - FIG 23

If the Right Turn Signal is triggered, the VAVSMOD2 will give the driver a top view and a Right-side view

Voyager VAVSMOD2 360 Camera System - FIG 24

If the vehicle gear is set to Reverse, the VAVSMOD2 will give the driver a full-screen Rear view

Voyager VAVSMOD2 360 Camera System - FIG 25

Note: Reverse trigger has the top priority. Whenever the turn light and backward are both triggered, the VAVSMOD2 shows the backward view.

Specification

VAVSMOD2 ECU

Power Supply| DC 12V
Power Consumption| 700 mA (Max)
Working Temp| -40 ℃ ~ +85 ℃
Storage Temp| -40 ℃ ~ +95 ℃
Input Signal| AHD 720P
Video Input| Camera 4
Video Output| CVBS/NTSC (640
480 Pixel)
IR port| 1
USB port| 1
VAVSCAM2 CAMERA (SOLD SEPARATELY)
Image Sensor| 1/3“ (SONY)
Resolution| 1.2M
Optical Lens| 2G4P + IR Cut
Aperture| 2.0
FOV| 190° (H)/ 140° (V)
Optical Decenter| 5 Pixel
Operating Temperature| -20°C ~ 70°C
Min Illumination| 0.1 Lux
Power Supply| DC 12V
Water Resistance| IP67

Trouble Shooting Guide

Issue Possible Causes Corrective Actions
No power Bad connection of power input Please check AVM power and ground

connection
No image on the screen| Monitor signal cable is not connected| Please check if the monitor signal cable is properly connected or if any pins inside the connector are bent
The fuzzy screen on the monitor| Dirt on the surface of the lenses| Please clean the lenses with soft and clean fabric
The screen image is not clear| Monitor display resolution is too low| Resolution with 480X234 above is recommended
**
The dark image on the screen| Camera video cable of the camera is not connected to the VAVSMOD2 ECU module| Please check if the camera video cable is connected or if any pins inside the connector are bent
Camera is damaged| Please replace the camera (may require re-calibration)
No function of left/right/reverse trigger| The trigger signal is not properly connected| Please check if the trigger signal is connected
The system  will not auto- calibrate| ** The calibration Mat is obstructed| Check for objects obstructing the camera view of the Mats. Fold in side mirrors if they are obstructing.


Calibration Mats are not within the Red Box

| Perform calibration camera check (press 02580258 on the remote). Check that the Mats are within the red box AND above the blue Mat Extension Index Line.
**** Poor lighting or Shadows on the calibration Mats| Check for poor lighting conditions or shadows that are being cast onto the calibration Mats. Correct the poor light condition.

Version 1.2
July 26, 2021

Documents / Resources

| Voyager VAVSMOD2 360 Camera System [pdf] User Manual
VAVSMOD2, 360 Camera System, VAVSMOD2 360 Camera System
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals