CONDTROL Vector 60 Laser Distance Meter User Manual
- June 4, 2024
- CONDTROL
Table of Contents
CONDTROL Vector 60 Laser Distance Meter
INTRODUCTION
Congratulations on your purchase of laser distance meter Vector 60/80 CONDTROL. Safety instructions can be found in the end of this user manual and should be carefully read before you use the product for the first time.
SAFETY REGULATIONS
- The user manual should be read carefully before you use the product for the first time. Unintended use of the product can be dangerous for human’s health and cause serious injury.
- Keep this user manual. If the product is given to somebody for temporary use, be sure to enclose user manual to it.
- Do not misuse the product
- Do not remove warning signs and protect them from abrasion, because they contain information about safe operation of the product.
- The device belongs to laser product class 2 in accordance with
- Do not look into the laser beam or its reflection, with unprotected eye or through an optical instrument. Do not point the laser beam at people or animals without the need. You can dazzle them.
- To protect your eyes close them or look aside.
- It is prohibited to disassemble or repair the product yourself. Entrust product repair to qualified personnel and use original spare parts only.
- Do not use the product in explosive environment, close to flammable materials.
- Avoid heating the batteries to avoid the risk of explosion and electrolyte leakage. In case of liquid contact with skin, wash it immediately with soap and water. In case of contact with eyes, flush with clean water during 10 minutes and consult the doctor.
INTENDED USE
Laser distance meters Vector 60 and Vector 80 are intended to measure
distance, to calculate area and volume of measured objects, perform
calculations by tilt sensor and Pythagoras’ Theorem, point to point
measurements, store results of measurement/calculation in memory and also
transmit via Bluetooth. The product is suitable for use at both indoor and
outdoor building areas. -Vector 80 only.
DELIVERY PACKAGE
The delivery package includes:
- Laser distance meter – 1pc.
- Carry pouch with a strap – 1 pc.
- User manual – 1 pc.
- USB charger – 1 pc.
TECHNICAL SPECIFICATIONS
Use a reflective plate to increase the measurement range during daylight or if the target has poor reflection properties. Accuracy can decrease in unfavorable conditions, such as intense sunshine or when measurements are made against glossy or transparent surfaces, moving objects, objects with rough surface. In unfavourable conditions or when measured distance is over 100 m themaximum permissible accuracy is calculated in the following way:
- ± (Y + 0,25хDх10-3) mm, where
- D (mm) – measured distance
- Y (mm) – permissible accuracy according to technical data.
PRODUCT DESCRIPTION
- Display
- Keyboard
- A hole for the strap
- End-piece
- Tripod thread 1/4’’
- Mini-USB connector for charging
Functions of buttons
Display
- Main line for displaying measuring results
- Additional lines for displaying measuring results
- Indication of tilt angle
- Indication of the mode
- Indication of point to point function
- Indication of Bluetooth
- Indication of battery charge level
- Indication of max/min values
- Indication of reference point
- Indication of measuring unit
- Indication of memory
OPERATION
Battery charging
Charge level is shown on display. Charge the battery when symbol appears on
the display. Use USB charger delivered in the set only. It is not recommended
to use the product while charging. It takes approximately 3 hours to fully
charge the batteries.
Switch on/off the device
- To switch on the device short press .
- To switch off the device press and hold during 1 second.
Measuring unit
Short press and simultaneously to enter service settings. Short press the button to select required measuring unit – m/ft/in (meters/feet/inches).Short press to confirm and return to single distance measurement mode.
Reference point
Press and hold button for 1 second to select the reference point. Appropriate
indicator will appear on the display
Measurements
Single distance measurement
Continuous distance measurement (Tracking)
Addition/subtraction
CALCULATIONS
Area
Wall surface (Vector 80 only)
Volume
Calculation of horizontal distance with the help of tilt sensor (Vector 80 only)
Calculation of distance by 2 additional measurements (Pythagoras 1)
Calculation of distance by 3 additional measurements – sum of cathetuses (Pythagoras 2)
Calculation of distance by 3 additional measurements – subtraction of 2 cathetuses (Pythagoras 3)
Point to point measurement (Vector 80 only)
Memory
Bluetooth
Bluetooth function is always on by default. Symbol is permanently shown on the display. Activate Bluetooth in the smartphone, tablet PC or laptop. For further operation use application Smart Measure .
MESSAGE CODES
While operation, the following codes/symbols may appear on the display:
CARE AND MAINTENANCE
Attention! The instrument is a precise device and requires careful handling. The following recommendations will extend the life of the product:
- Do not point the product at the sun.
- Protect the product from bumps, falls, and excessive vibration; do not let liquids, construction dust and foreign objects get inside the product.
- Do not expose the product to extreme temperatures.
- If liquids get inside the product first remove the batteries, then contact the service center.
- Do not store or use the product under high humidity conditions for a long time.
- Clean the product with soft wet cloth.
- Keep device optics clean and protect it from mechanical damage.
- Сarry out control measurements occasionally, especially if the product is subject to excessive mechanical or other impact, before and after taking important measurements.
UTILIZATION
Expired tools, accessories and package should be passed for waste recycle. Please send the product to the following address for proper recycle:
CONDTROL GmbH Wasserburger Strasse 9 84427 Sankt Wolfgang
Germany
Do not throw the product in municipal waste! According to European directive 2002/96/ЕC expired measuring tools and their components must be collected separately and submitted to environmentally friendly recycle of wastes.
WARRANTY
All CONDTROL GmbH products go through post-production control and are governed by the following warranty terms. The buyer’s right to claim about defects and general provisions of the current legislation do not expire.
- CONDTROL GmbH agrees to eliminate all defects in the product, discovered during the warranty period, that represent the defect in material or workmanship in full volume and at its own expense.
- The warranty period is 36 months and starts from the date of purchase by the end customer (see the original supporting document).
- The warranty dösn’t cover defects resulting from wear and tear or improper use, malfunction of the product caused by failure to observe the instructions of this user manual, untimely maintenance and service and insufficient care, the use of non-original accessories and spare parts. Modifications in design of the product relieve the seller from responsibility for warranty works. The warranty dös not cover cosmetic damage, that dösn’t hinder normal operation of the product.
- CONDTROL GmbH reserves the right to decide on replacement or repair of the device.
- Other claims not mentioned above, are not covered by the warranty.
- After holding warranty works by CONDTROL GmbH warranty period is not renewed or extended.
- CONDTROL GmbH is not liable for loss of profit or inconvenience associated with a defect of the device, the rental cost of alternative equipment for the period of repair.
This warranty applies to German law except provision of the United Nations Convention on contracts for the international sale of goods (CISG). In warranty case please return the product to retail seller or send it with defect description to the following address:
CONDTROL GmbH Wasserburger Strasse 9 84427 Sankt Wolfgang Germany
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>