MAGICFX SMOKEJET Smoke Machine with Built In Power LED User Manual
- June 4, 2024
- MAGICFX
Table of Contents
MAGICFX SMOKEJET Smoke Machine with Built In Power LED
DISCLAIMER
WARNING Read this manual carefully before installing and/or using this product. Failure to read the manual and to follow the printed instructions may lead to personal injury and/or damage to the product.
2019 MAGICFX
All rights reserved.
Nothing from this publication may be copied, reproduced and/or published by
means of printing, photocopying or by any other means, without the prior
written approval Of MAGIC FX.
MAGIC FX reserves the right to modify the specifications stated in this
manual.
TRADEMARKS
Any brand names mentioned in this manual are registered trademarks of their
respective owners.
LIABILITY
MAGIC FX accepts no liability for claims from third parties arising from
unauthorized use, use other than that stated in this manual, and use other
than in accordance with the General Conditions registered at the Chamber Of
Commerce. We further refer to the General Conditions. These are available on
request, free of charge.
Although considerable care has been taken to ensure a correct and
comprehensive description of all relevant components, the manual may
nonetheless contain errors and inaccuracies.
Should you detect any errors or inaccuracies in the manual, we would be
grateful if you would inform us. This helps us to further improve our
documentation.
FOREWORD
Congratulations! You have bought a great new product from MAGIC FX.
This manual contains all information required for the intended use of the
equipment. Deviation from the described intended use can result in a hazardous
situation and/or property damage.
This manual includes notes and warnings on safe operation of the equipment.
These notes and warnings are accompanied by the following icons. Read them
attentively
DANGER: Indicates a hazardous situation that, if not avoided, will result
in death or serious injury. This signal word is to be limited to the most
extreme situations.
WARNING: Indicates a hazardous situation that, if not avoided, could
result in death or serious injury
CAUTION: Indicates a hazardous situation that, if not avoided, could
result in minor or moderate injury
NOTICE: Indicates information considered important, but not hazard-
related (e.g. messages relating to property damage).
LANGUAGE
This document contains the original instructions in English. In case you
require other languages please contact MAGIC FX.
REVISION TABLE
Doc nr| Revision| Date| Description| Author|
Approved
---|---|---|---|---|---
PART01085| 01-00| 20-08-2018| Initial release| TVA| WH
PART01085| 01-02| 04-01-2021| New design| NE| LL
SAFETY INFORMATION
WARNING
Please read the following safety information carefully before operating the machine. Information includes important safety information about installation, usage, and maintenance. Pay attention to all warning labels and instructions in this manual and printed on the machine.
If you have questions about how to operate the machine safely, please contact your local MAGIC FX dealer for help.
- Keep this device dry.
- Always connect to a grounded circuit to avoid risk of electrocution.
- Before connecting machine to power, always check voltage indicate on machine match to your local AC voltage. Do not use the machine if AC power voltage does not match.
- Disconnect the machine from AC power before servicing and when not in use.
- This product is for indoor use only! Do not expose to rain or moisture. If fluid is spilled, disconnect AC power and clean with a damp cloth. If fluid is spilled onto electronic parts, immediately unplug the machine and contact your local MAGIC FX dealer for advice.
- No user-serviceable and modifiable parts inside. Never try to repair this product, unauthorized technician may lead machine to damage or malfunction.
- For adult use only. Never leave the machine running unattended.
- Installed in well-ventilated area. Provide at least 50 cm space around the machine.
- Never add flammable liquid of any kind to the machine.
- Make sure there are no flammable materials close to the machine while operating.
- Only use MAGIC FX fluid. Other fluid may lead to heater clog and malfunction.
- If the machine fails to work, unplug the machine and stop operation immediately. Contact your local MAGIC FX dealer for advise.
- Before transporting the machine, make sure the fluid tank is completely drained.
- Smoke fluid may present health risks if swallowed. Do not drink smoke fluid. Store it securely. In case of eye contact or if fluid is swallowed immediately look for medical advice.
MAIN PARTS
TECHNICAL DATA
Product | Product Name | MAGICFX® SMOKEJET |
---|---|---|
Product Code | MFX0901 | |
Product Type | SMOKE FX | |
Main Dimensions | Length | 345 mm |
13.6 in
Width| 193 mm 7.6 in
Height| 386 mm 15.2 in
Weight Weight| 11.1 kg (dry) 13.6 kg (full) 24.5 lb / 30 lb
Electrical| Voltage Input| 230 – 250 Vac
Voltage Frequency| 50 – 60 Hz
Power Consumption| 1420 W
Power Connector| Neutrik® powerCON TRUE1 (in & out)
Usage| Consumable(s)| MAGICFX® SMOKEJET fluid
Consumable Consumption| ****
MAGICFX® SMOKEJET fluid 2.5 ml/s
PRODUCT IDENTIFICATION
ACCESSORIES
Code | Product | Included |
---|---|---|
PART01157 | REMOTE | X |
MFX0313 | SCHUKO TO NEUTRIK® POWERCON TRUE1 – CABLE 1.5 m | |
MFX0911 | MAGICFX® SMOKEJET FLIGHTCASE (FOR 4 PCS) | |
MFX3106 | MFX3106 HALF COUPLER (100kg) M10 | |
SPR00119 | SAFETY STEEL 60 cm – 25 kg | |
Accessories |
Please contact MAGIC FX for additional possibilities.
FX FLUIDS
The MAGICFX® SMOKEJET uses MAGICFX® SMOKEJET FLUID to create the smoke effect. The fluid is delivered in a can. Do not use other fluids than those that are approved and supplied by MAGIC FX, see following table.
Code | Type of fluid | Volume |
---|---|---|
MFX3070 | MAGICFX® SMOKEJET FLUID | 5 litre |
Approved FX Fluids |
OPERATE SAFELY!
WARNING
Please read the following safety information carefully before operating the machine. Information includes important safety information about installation, usage, and maintenance. Pay attention to all warning labels and instructions in this manual and printed on the machine
If you have questions about how to operate the machine safely, please contact your local MAGIC FX dealer for help.
GENERAL SAFETY RULES
- Keep this device dry.
- Always connect to a grounded circuit to avoid risk of electrocution.
- Before connecting machine to power, always check voltage indicate on machine match to your local AC voltage. Do not use the machine if AC power voltage does not match.
- Disconnect the machine from AC power before servicing and when not in use.
- This product is for indoor use only! Do not expose to rain or moisture. If fluid is spilled, disconnect AC power and clean with a damp cloth. If fluid is spilled onto electronic parts, immediately unplug the machine and contact your local MAGIC FX dealer for advice.
- No user-serviceable and modifiable parts inside. Never try to repair this product, unauthorized technician may lead machine to damage or malfunction.
- For adult use only. Never leave the machine running unattended.
- Installed in well-ventilated area. Provide at least 50 cm space around the machine.
- Never add flammable liquid of any kind to the machine.
- Make sure there are no flammable materials close to the machine while operating.
- Only use MAGIC FX fluid. Other fluid may lead to heater clog and malfunction.
- If the machine fails to work, unplug the machine and stop operation immediately. Contact your local MAGIC FX dealer for advise.
- Before transporting the machine, make sure the fluid tank is completely drained.
- Smoke fluid may present health risks if swallowed. Do not drink smoke fluid. Store it securely. In case of eye contact or if fluid is swallowed immediately look for medical advice.
RIGGING
Please follow the European and national guidelines for safe rigging and
trussing
SAFETY SYMBOLS
Symbol | Meaning |
---|---|
**** | **** Read the manual carefully before use! |
PRECAUTIONS FOR OPERATION
WARNING: Using a damaged or an improper installed machine can lead to
death, serious injury or property damage. Always inspect the machine
thoroughly before operation
WARNING: Unauthorized operation of the machine can lead to death, serious
injury or property damage. Never leave the machine unattended when the machine
is ready for use.
WARNING: Do not use the MAGICFX® SMOKEJET if alterations have been made
other than by or on behalf of MAGICFX®.
WARNING: Make sure there are no objects near the input grill that can
block the air to be sucked in.
CAUTION: Always follow the instructions as noted on the cans.
CAUTION Missing or obscured safety symbols on the machine can lead to
death, serious injury or property damage. Make sure all safety symbols are
correctly in place and visible, see section 2.3.
NOTICE Do not use other fluids than those that are approved and supplied
by MAGIC FX, see Section 1.5.
SETTING UP
INSTALL THE MACHINE.
-
Place the machine on a flat surface and in a suitable large area with at least 50 cm open space around the machine.
-
Fill the fluid tank with MAGICFX® approved fluid.
-
Connect the machine to suitable rated power supply. To determine the power requirement for the machine refer to the label on the back of the machine.
WARNING: Always connect the machine to a protected circuit and ensure it is properly grounded to avoid risk of electrocution -
Turn on the machine and allow it to heat up. Heat up takes approximately 5 mintues. Once the machine has reached operating temperature, the LCD display will show “Ready To Fog”. Now the machine is ready for operation.
-
To start making fog, locate the OUTPUT button on the control panel, and press the button to start making fog.
-
To turn off the machine, press STOP button and turn POWER CON TRUE1 to the OFF position.
OPERATION
CONTROL PANEL OPERATION.
The machine can be operated with the onboard digital control interface
Button | Function |
---|---|
(MENU) | Scroll through setting menu |
[UP]/[TIMER] | Up/Activate Timer function |
[DOWN]/[OUTPUT] | Down/Activate Output function |
[STOP] | Deactivate Timer/Volume function |
CONTROL MENU.
WIRELESS OPERATION.
Wireless remote control system consists of a transmitter equipped with four buttons to activate four user-configurable LED settings and fog; with an onboard receiver attached to the rear panel of SmokeJet.
Wireless settings are configurable through the onboard control panel, refer to
the control menu section to set up each button.
In free open space the effective distance is 50 meters, actual usage depending
on obstacle level the effective distance is 10-25 meters.
REGISTERING TRANSMITTER.
The transmitter can be paired or deleted from the receiver. Each receiver can pair up to 10 transmitters. Follow the steps below to pair or delete the transmitter from the receiver
- Power off SMOKEJET
- Press and hold [DOWN] button
- Turn power on and release [DOWN] button when LCD display blinks
- Follow the menu instruction to pair or delete transmitter
TRANSMITTER BATTERY REPLACEMENT.
If the effective distance seems to be decreased, it is possible that the
battery level is low and requires a replacement. In order to replace the
battery, undo the three screws on the back of transmitter to release the
cover. Replace with same battery- type and specification of battery which is
27A-12V.
DMX CONNECTOR PIN ASSIGNMENT
The machine provides 5 pin XLR connector for DMX connection. Diagram below
indicate pin assignment information.
Pin | Function |
---|---|
1 | Ground |
2 | Data- |
3 | Data+ |
DMX CHANNEL FUNCTION.
Channel 1 | DMX Value Range | Function |
---|---|---|
Fog | 0 – 4 | Fog Off |
5 – 255 | Fog On | |
Channel 2 | ||
Red LED | 0-255 | 0-100% |
Channel 3 | ||
Green LED | 0-255 | 0-100% |
Channel 4 | ||
Blue LED | 0-255 | 0-100% |
Channel 5 | ||
Amber LED | 0-255 | 0-100% |
Channel 6 | ||
Chase | 1-15 | Chase 1 |
16-31 | Chase 2 | |
32-47 | Chase 3 | |
48-63 | Chase 4 | |
64-79 | Chase 5 | |
80-95 | Chase 6 | |
96-111 | Chase 7 | |
112-127 | Chase 8 | |
128-143 | Chase 9 | |
144-159 | Chase 10 | |
160-175 | Chase 11 | |
176-191 | Chase 12 | |
192-207 | Chase 13 | |
208-223 | Chase 14 | |
224-255 | Chase 15 | |
Channel 7 | ||
Chase Speed | 0-255 | 0-255 step per min |
Channel 8 | ||
Master Dimmer | 0-255 | 0-100% |
Channel 9 | ||
Strobe | 0-255 | 1-20 Hz |
CLEAN UP
- Do not allow the machine to become contaminated.
- Remove dust from air vents with air compressor, vacuum or a soft brush.
- Only use a damp cloth to clean the casing.
- Before storing run distilled water through the system to help avoid condensing the pump or heater.
- It is recommended to run the machine on a monthly basis in order to achieve best performance and output condition.
- Excessive dust, liquid and dirt built up will degrade performance and cause overheating.
MAINTENANCE
To achieve the maximum service life of the MAGICFX® SMOKEJET you must
regularly clean the MAGICFX® SMOKEJET and test if it is functioning correctly.
Contact MAGIC FX if the MAGICFX® SMOKEJET is not functioning correctly.
DANGER: Do not replace parts yourself; always consult MAGIC FX.
TROUBLESHOOTING
Always contact MAGIC FX if any malfunctions or errors occur that cannot be solved with the instructions as described in this manual.
BREAKER RESET
Breaker
230V = 9A 250V
WARNING: Disconnect AC power before reset breaker. Only replace fuse with same type and rating
- Disconnect AC power
- Flip breaker to ON position
- Turn on machine to test
FAQ
Why does the machine not respond on any wired DMX input?
Make sure the W-DMX512 is turned OFF.
CORRECT DISPOSAL
This symbol on the product and / or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper treatment, recovery and recycling, please take this product to designated collection points where it will be accepted free of charge. Alternatively, in some countries you may be able to return your products to your local retailer upon purchase of an equivalent new product.
Disposing of this product correctly will help save valuable resources and
prevent any potential negative eff ects on human health and the environment,
which could otherwise arise from inappropriate waste handling.
Please contact your local authority for further details of your nearest
designated collection point.
Penalties may be applicable for incorrect disposal of this waste, in
accordance with your national legislation.
EC DECLARATION OF CONFORMITY
According to Annex III A Machinery Directive 2006/42/EC
MAGIC FX B.V. declares as manufacturer and composer of the technical
construction file that the product with the following specifications:
- Name machine : SMOKEJET
- Type : MFX0901
- Voltage : 230–250 Vac 50-60Hz
- Serial number : on product
- Year of construction: on product
Is in conformity with the minimal safety regulations as stated in the following directive(s):
- LVD (2014/35/EU) Low Voltage Directive
- EMC (2014/30/EC) ElectroMagnetic Compatibility
- RoHS (2011/65/EU) Restriction of the use of certain Hazardous Substances
- WEEE (2012/19/EU) Waste Electrical & Electronic Equipment
The following harmonized standards were applied:
- NEN-EN-ISO 12100:2010 Safety of machinery -General principles for design – Risk assessment and risk reduction.
- NEN-EN-IEC 60204-1:2018, Safety of machinery -Electrical equipment of machines – Part 1: General requirements.
- NEN-EN-IEC 61000-6-3:2007/A1:2011, Electromagnetic compatibility (EMC) – Part 6-3: Generic standards – Emission standard for residential, commercial and light-industrial environments.
Original declaration of conformity
Translation of the original declaration of conformity
- Name manufacturer: MAGIC FX BV
- Address : Schouwrooij 27, 5281 RE BOXTEL
- Country : The Netherlands
- CEO : B. Veroude
- Date : 4-1-2021
Signature
Documents / Resources
|
MAGICFX SMOKEJET Smoke Machine with Built In Power
LED
[pdf] User Manual
PART01085, SMOKEJET, Smoke Machine with Built In Power LED, SMOKEJET Smoke
Machine with Built In Power LED, Smoke Machine
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>