RADDY WF-55C Weather Station User Manual
- June 3, 2024
- RADDY
Table of Contents
WF-55C
WEATHER STATION
USER MANUAL
WF-55C Weather Station
Please read the instruction before using the product and keep it for future
reference.
Any questions, please feel free to contact
support@iraddy.com or visit
www.iraddy.com
READ BEFORE USE
- Do not clean any part of the product with benzene, thinner, or other solvent chemicals. If necessary, clean it with a soft cloth.
- Do not dismantle or modify the product in any way.
- Never immerse the product in water, It will damage the product.
- Do not subject the product to extreme force, shock, or fluctuations in temperature or humidity.
- Do not tamper with the internal components.
- Do not use new and used batteries.
- Do not use different types of batteries alkaline, standard, or rechargeable batteries with this product.
- Remove the batteries if storing this product for a long period of time, otherwise, the battery might damage the product.
- Do not dispose of this product as unsorted municipal waste, it’s necessary to separately collect it for special treatment.
- Do not place the base station in rain or moisture.
- The transmit range depends on the type of obstacles located between the transmitter and the receiver (e.g. a concrete wall will interfere with the signal much more than a plasterboard wall).
- Be sure the sensor is mounted vertically, to allow moisture to drain out properly. Place out of direct sunlight & ensure the sensor is well-ventilated.
IMPORTANT PLACEMENT GUIDELINES
- The distance between the base station and sensors should be at least 5 ~ 6.5 feet (1.5~2 meters) away from any interfering sources such as computer monitors or TV sets.
- The base station stays away from the metal window frames.
- Please do not use other electrical products such as headphones or microphones operating on the same signal frequency. (433.92MHz), neighbors using electrical devices operating on the same signal frequency can also cause interference.
- Place the base station in a dry area, free of dirt and dust. To ensure accurate temperature measurement, place out of direct sunlight and away from heat sources or vents.
PACKAGE CONTENTS
1 x Weather Station
1 x Remote Sensor
1 x User Manual
1 x DC Adapter
*Alkaline batteries are not included
INSTALLATION
Sensor Set Up
Base station supports up to 3 sensors connection, the sensor switch is located
inside the battery compartment, and it can be switched 1,2,3, matching the
info of Channel 1, Channel 2, and Channel 3 that synchronizes on the OUTDOOR
Dashboard, install 2 alkaline AA batteries to activate the sensor.
Base Station Set Up
Remove the protective film that is applied to the LCD screen prior to using
the product.
Plugged in with power adapter and used, battery power is optional, since the
previous setting will be reset when plugged out, we recommend installing the
batteries for the base station. Base station can stand upright on the table or
mount on the wall.
Connect The Sensor & Base Station
- Install the batteries for the remote sensor, and slide the channel number.
- Plug the power adapter into the base station, then it will start to receive the sensor signal within 3 minutes.
- If the red indicator of the sensor flashes twice, and you see the detected data displayed located on the left of the screen, it means the sensor is connected with the base station.
- When the red indicator of the sensor flash once per minute, it indicates that it is updating the sensor data to the base station.
Example, when you slide to channel 1 for your sensor, you can see the data shown the data on the CH1 dashboard.
OVERVIEW
1 | Channel | 13 | Time |
---|---|---|---|
2 | 3 outdoor channels display in a loop | 14 | Outdoor humidity |
15 | Comfort dashboard for outdoor | ||
3 | Low battery indicator (Sensor) | ||
16 | Max/Min record for outdoor temperature and humidity in 24 hours | ||
4 | Weather forecast | ||
5 | FREEZE WARNING | ||
6 | Indoor temperature | 17 | Outdoor Temperature |
7 | Low battery Indicator (base station) | 18 | Touch button – ( Zf /ii:- ) |
SNOOZE/LIGHT
8| Trends for indoor temperature and humidity| 19| SET = function setting
button
♦/CH = up or channel switch,
♦/MEM = down or MAX/MIN records checking,
ALARM = Alarm clock setting)
9| Max/Min record for indoor temperature and humidity in 24 hours
10| Comfort dashboard for indoor| 20| Hang Holes for wall mounting
11| Indoor humidity| 21| Table stand
12| Calendar| 22| Battery compartment cover
Sensore Remoto
- LED indicator
- Battery compartment cover
- Hang hole for wall mounting
- Channel slide switch
- A hole for hanging strip
FEATURES
- Time and Calendar (Day/Month)
- 12/24 hours format switchable
- Alarm with snooze function
- Weather forecast with 5 variables: sunny, partly cloudy, cloudy, rainy, and snowy
- Indoor temperature and humidity
- Outdoor temperature and humidity
- Support up to 3 sensors (1 included)
- Automatically loop the temperature and humidity of 3 outdoor sensors
- Max/ Min memory records for all indoor/outdoor temperature and humidity
- Trend index
- C/F(Celsius/Fahrenheit) switchable
- Comfort dashboard
- Low battery indicator
- Key tone on/off
- Transmission range: up to 100 meters/330 feet in open area
- 3-mode brightness: Bright/Dim/Off
- Support desk standing or wall hanging
CHANNEL SETTING
Press【▲/CH】button to check the outdoor temperature and humidity of channel 1/2/3. When you switch to the mode, the display will automatically loop 3 sensors’ data. If you want to reset all the data of the sensors, press and hold the 【▲/CH】button 3 seconds, and it will reconnect with the sensors.
FUNTIONS SETTING MODE
Press and hold【SET】button, to enter the SETTING MODE, once in SETTING MODE the preference you are currently setting will blink in the middle of the display. During setting, only the setting figure will display, other parts will be invisible. To adjust the currently flashing item, press【▲/CH】or 【▼/MEM】buttons (press and hold to fast adjust). To save your adjustments, press and release the【SET】 button to adjust the next preference. (The setting will be automatically save and exit if there is no operation within 20 seconds.)
The preference set order is as follows:
KEY TONE ON/OFF
TIME FORMAT 12/24H
CLOCK HOUR
CLOCK MINUTE
CALENDAR YEAR
CALENDAR DATE FORMAT (MONTH-DAY or DAY-MONTH)
CALENDAR MONTH
CALENDAR DATE
C/F (CELSIUS/FAHRENHEIT)
TOUCH ADJUSTABLE BACKLIGHT
When the base station is powered with batteries only, touch 【SNOOZE/LIGHT 】for 1 second at the top, momentarily light up the screen for 20 seconds. When powered by the adapter, touch【SNOOZE/LIGHT】to adjust the brightness BRIGHT- DIM-OFF.
ALARM CLOCK SETTING
Press【ALARM】button to turn ON/OFF the alarm. If the alarm is on, the alarm
icon will be located between an hour and a minute; If the alarm is off, the
alarm icon will disappear. It will return to normal time display mode if no
operation in 5 seconds. Press and hold 【ALARM】 button to enter the ALARM CLOCK
MODE.
Once in ALARM CLOCK MODE the preference you are currently setting will blink
on the screen.
To adjust the currently flashing item, press【▲/CH】or 【▼/MEM】buttons (press and
hold to fast adjust). To save your adjustments, press and release the【ALARM】
button to adjust the next preference. (The setting will be automatically save
and exit if there is no operation within 20 seconds.)
SNOOZE SETTING
The alarm sound will last for 2 minutes then be canceled automatically. It
will make a sound as follow:
0-10 seconds: Beep per second
11-20 seconds: Beep x 2 per second
21-30 seconds: Beep x 4 per second
31-120 seconds: Keep BI sound
To snooze the alarm, press【SNOOZE/LIGHT】button to enter into SNOOZE MODE for 5
minutes, and the snooze icon will display.
To stop the alarm, press any other button, but sounds again if the alarm
condition reoccurs.
To deactivate the alarm, press【ALARM】button to turn it off.
LOW BATTERY ALERT
- When the battery-powered base station is lower than 3.6V, or when the power for the remote sensor is lower than 2.5V, the low battery indicator will display on the screen, indicating that it’s time to change the batteries.
- When it is powered by DC adapter, the batteries could a memory of the time and date, even though the base station is powered off, the memorized setting would not be reset.
- To avoid the power runs out, the batteries getting rotten, and damaging the units, please change batteries on time when low battery reminders show up.
- Please use alkaline dry batteries, do not use rechargeable batteries.
MAX/MIN RECORD
Press【▼/MEM】button to check the MAX/MIN temperature and humidity record for 3
channel sensor, the preference set order is as follows:
Maximum temperature & humidity
Minimum temperature & humidity
Current temperature & humidity
The records will be cleared automatically at 00:00 every day, or manually
cleared by press and holding the 【▼/MEM】button.
WEATHER FORECAST
WEATHER ICON| | | | |
---|---|---|---|---|---
Description| Sunny| Partly Cloudy| Cloudy| Rainy| Snowy
Weather forecast in 12+ Hour: Sunny, Partly Cloudy, Cloudy, Rainy, Snowy.
The weather forecast is based on collecting hourly temperature & humidity from
the outdoor sensor. The forecast station predicts weather conditions for the
next 12 hours with
70-75% accuracy.
The default weather icon is partly cloudy, the base station will calibrate the
weather report in 1-2 weeks with the outdoor temperature and humidity data.
The remote sensor should be placed outside to get accurate outdoor data or it
will affect the accuracy of the weather forecasts.
COMFORT INDEX
Comfort Index | Humidity Range |
---|---|
Dry | 1-40% |
Good | 41-75% |
Wet | ≧ 76% |
LOW-TEMPERATURE ALERT
When the remote sensor detects the temperature drop to 0-2.9 °C (32-37.2 °F),
the snow icon will flash; when the temperature value is lower than 0 ℃ , the
snow icon will keep displaying at the top of the weather forecast.
TRENDS
The trend icon will display when the temperature increase 1℃ compared to the
last data, or increase 1℃ in 1 hour;
The trend icon will display when the humidity value increase by 3% compared to
the last data, or increase 3% in 1 hour. Vice the verse for decreased trends.
When the increase/decrease is less then 1℃ or 3% in 1 hour, the trend icon
will not display.
TROUBLESHOOTING
Problem | Solution |
---|
–.-
(No data shown on outdoor
dashboard)| 1. Make sure the base station is powered on
2. Make sure the sensor installed on the batteries
3. If there is no sensor signal received in 3 minutes, the base station will
stop receiving the signal. Press and hold the 【▲/CH】button for 2 seconds to
re-synchronize the sensor.
4. Try to turn off/remove away from other existing wireless equipment.
5. Replace new batteries.
Uninstall the sensor or switch
the channel number on the
sensor, there is no change.| When you uninstall the sensor or switch to the
other channel, the signal of the previous sensor will become weaker but won’t
disappear immediately, it will clear the data and display “–.-” or re-
synchronize the new sensor data next hour until the signal gone
SPECIFICATION
UNIT | TEMPERATURE RANGE | HUMIDITY RANGE |
---|---|---|
BASE STATION | – 9,9 ℃ ~ 50 ℃ | 1%RH~99%RH |
REMOTE SENSORS | – 40 ℃ ~ 60 ℃ | 1%RH~99%RH |
OUT OF
RANGE| ● Show HH.H when base station >50
℃ (122 ℉ ), or remote sensors >60
℃ (140 ℉ )
● Show LL.L when base station <-9.9 ℃ (14 ℉ ) or remote sensors < -40
℃ / (-40 ℉ )| Show HH >99%RH
Show LL<1%RH
BASIC SPECS
Sensor Transmission
Frequency| 433.92MHz
---|---
Alimentazione della stazione base| 3 x 1.5V type AAA alkaline batteries
& 5V 1.2A DC Adapter (Included)
Signal Transmission Distance| 300ft (100m) in an open area
Waterproof Rating| IP54
Sensor Hanging Hole| Compatible with <0.3cm diameter screw
For better accuracy of product, please place the sensor lengthwise/standing up and at least 5~ 6.5 feet (1.5~2 meters) away from the ground. Avoid exposing the sensor to direct sunlight for a long time.
support@iraddy.com
www.iraddy.com
Made in China
Documents / Resources
|
RADDY WF-55C Weather
Station
[pdf] User Manual
WF-55C Weather Station, WF-55C, Weather Station, Weather, Station
---|---
|
RADDY WF-55C Weather
Station
[pdf] User Manual
WF-55C Weather Station, WF-55C, Weather Station, Station