AUTOMATE DCFT15 Rechargeable Battery Pack Instruction Manual
- June 4, 2024
- AUTOMATE
Table of Contents
Rechargeable Battery Pack
INSTRUCTION MANUAL
DCFT15 Rechargeable Battery Pack
The rechargeable Lithium-Ion battery pack enables Automate DCFT motor to operate wirelessly and without the constraints of traditional battery wands with disposable batteries.
FEATURES:
- Provides up to 6-12 months on a single charge (depends on shade size, fabric weight& usage)
- Battery pack fully recharges in ~ 7 hours
- Battery health status reported in Automate Pulse App
SAFETY INSTRUCTIONS
WARNING: Important safety instructions to be read before installation.
Incorrect installation can lead to serious injury and will void manufacturer’s
liability and warranty.
WARNING: Important safety instructions to be read before installation and
use.
Incorrect installation or use can lead to serious injury and will void
manufacturer’s liability and warranty.
It is important for the safety of persons to follow the enclosed instructions.
Save these instructions for future reference.
- Do not expose to water, moisture, humid and damp environments or extreme temperatures.
- Persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge should not be allowed to use this product.
- Use or modification outside the scope of this instruction manual will void warranty.
- Installation and programming to be performed by a suitably qualified installer.
- Follow installation instructions.
- For use with motorized shading devices.
- Keep away from children.
- Frequently inspect for improper operation. Do not use if repair or adjustment is necessary.
- Keep clear when in operation.
- Replace battery with correctly specified type.
COMPLIANCE STATEMENT
This device complies with Part 15 of the FCC Rules / Industry Canada licence- exempt RSS standard(s). Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
Do not dispose of in general waste.
Please recycle batteries and damaged electrical products appropriately.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
To satisfy FCC / IC RF exposure requirements, a separation distance of 20 cm
or more should be maintained between the antenna of this device and persons
during device operation.
To ensure compliance, operations at closer than this distance is not
recommended.
INSTALLATION
1.1 Charging
IMPORTANT
Rechargeable Battery Pack must be fully charged prior to first use to prolong
battery lifespan.
Step 1. Connect the Rechargeable Battery Pack to the Automate charger.
MT03-0301-050017 + MT03-0305-050011
Step 2. Charge for 7 hours.
Step 3. Install as required.
See Section 1.2 Attachment Methods
Charging Cable
1.2 Attachment Methods
IMPORTANT
Recommended to install the battery in a horizontal orientation to minimize the
risk of water ingress. Ensure the battery is positioned away from direct
contact with water or exposure to adverse weather conditions during
installation.
1.3 Mounting Options
| |
---|---|---
Bottom Cassette
Front View| Side Rail
Side View| Top Cassette
Perspective View
1.4 Motor Connections
Charging uses a barrel type connector.
Motors
MT01-1245-069001 Motor Connection Cable
SPECIFICATIONS
| Input Voltage | 12.6 VDC |
|---|---|
| Typical Voltage | 12 VDC |
| Nominal Voltage | 10.8 V |
| Rated Energy | 5.1A Max |
| Input Current | 1A |
| Battery Size | 5100mAh |
| Battery Type | Li-ion Rechargeable |
| Temperature Working Range | 32°F to 140°F (0°C to 60°C) |
| Charging Time | ≈ 7 Hours |
ROLLEASE ACMEDA | USA
Level 7 / 750 East Main Street
Stamford, CT 06902, USA
T +1 800 552 5100
F +1 203 964 0513
ROLLEASE ACMEDA | AUSTRALIA
110 Northcorp Boulevard,
Broadmeadows VIC 3047, AUS
T +61 3 9355 0100
F +61 3 9355 0110
ROLLEASE ACMEDA | EUROPE
Via Conca Del Naviglio 18,
Milan (Lombardia) Italy
T +39 02 8982 7317
F +39 02 8982 7317
Automate™ Rechargeable Battery Instructions
MT03-0305-05011
ROLLEASE ACMEDA
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>