G3FERRARI G10188 Espresso Maker User Manual

G3FERRARI G10188 Espresso Maker

Specifications :

• Model: MD-2038BT
• Brand: G3 Ferrari
• Website: www.g3ferrari.it

Product Information

The MD-2038BT is a coffee machine with various features for brewing espresso and steam. It includes components such as a water tank, steam dispenser, heating element, filters for different cup sizes, and more.

Product Usage Instructions

Assembly:

1. Wash all removable parts.
2. Fill the water tank without exceeding the MAX level and place it securely.
3. Attach the drip tray to the front of the machine.
4. Place the cup tray on the drip tray. Ensure all parts are correctly assembled before turning on the machine.

First Use and Internal Circuit Cleaning:

1. Install the portafilter in its place.
2. Insert the portafilter aligning with the symbol and rotate clockwise until locked.

Operation:

1. Mount the water tank securely for proper operation.

FAQ:

• Q: Can I use hot or carbonated water in the water tank?
  A: No, only use fresh natural water in the water tank, not hot, carbonated, or other liquids.

• Q: How do I clean the machine?
  A: Follow the instructions in the user manual for cleaning and maintenance. Do not attempt to repair or modify the machine yourself.

USER MANUAL
Technical model: MD-2038BT Espresso maker ALCHIMIA
www.g3ferrari.it

PROTECTION CLASSES

WARNING
ELECTRIC SHOCK RISK
DO NOT EXPOSE TO RAIN OR MOISTURE

• This symbol warns the user that un-insulated dangerous voltage inside the system may cause an electrical shock. Do not open the case.
• Class I Appliance symbol. This means the appliance must have the chassis connected to electrical earth/ground by an earth conductor.
• Caution: this symbol reminds the user to read carefully the important operations and maintenance instructions in this owner’s guide.

SAFETY INSTRUCTIONS

• The following are important notes on the installation, use and maintenance; save this instruction manual for future reference; use the equipment only as specified in this guide; any other use is considered improper and dangerous; therefore, the manufacturer cannot be held responsible in the event of damages caused by improper, incorrect or unreasonable use.
• Before use, ensure the equipment is undamaged; if in doubt, do not attempt to use it and contact the authorized service center; do not leave packing materials (i.e. plastic bags, polystyrene foam, nails, staples, etc.) within the reach of children as they are potential sources of danger; always remember that they must be separately collected. Make sure that the rating information given on the technical label are compatible with those of the electricity grid; the installation must be performed according to the manufacturer’s instructions considering the maximum power of the appliance as shown on the label; an incorrect installation may cause damage to people, animals or things, for which the manufacturer cannot be considered responsible thereof.
• If it is necessary to use adapters, multiple sockets or electrical extensions, use only those that comply with current safety standards; in any case do not exceed the power consumption limits indicated on the electrical adapter and / or extensions, as well as the maximum power shown on multiple adaptor.
  • Do not leave the unit plugged; better to remove the plug from the mains when the device is not in use. Always disconnect from power supply if you leave it unattended. Cleaning operations should be carried out after unplugging the unit.
  • If the unit is out of order and you do not want to fix it, it must be made inoperable by cutting power cord.
  • Do not allow the power cord to get closer to sharp objects or in contact with hot surfaces; do not pull it to disconnect the plug.
  • Do not use the appliance in the event of damage to the power cord, plug, or in case of short circuits; to repair the product only address an authorized service center.
  • Do not handle or touch the appliance with wet hands or bare feet. Do not expose the appliance to harmful weather conditions such as rain, moisture, frost, etc.. Always store it in a dry place.
  • Children must not play with the appliance.
  • This appliance can be used by children of 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they received supervision or instruction concerning use of the appliance in a safe way and understand hazards involved; children shall not play with the appliance; cleaning and user maintenance shall not be made by children without supervision.
  • Keep the appliance and its cord out of reach of children less than 8 years.
• If the power cord is damaged, or in case of failure and / or malfunction do not tamper with the unit. The reparation must be done by manufacturer or by service center authorized by the manufacturer in order to prevent any risk. Failure to comply with the above may compromise the unit safety and invalidate the warranty.
• WARNING: This appliance includes heating function. Surfaces, other than functional surfaces may develop high temperatures. Since temperatures are perceived differently by different people, this device should be used with CAUTION. Hold the appliance exclusively to grip surfaces intended to be touched.
  • This appliance is intended to be used in household and similar applications such as: staff kitchen areas in shops, offices and other working environments; by clients in hotels, motels and other residential type environments; farm houses, bed and breakfast type environments.
  • The appliance is not intended to be operated by means of an external timer or separate remote-control system.
  • Before every use, unroll the power cord.
  • Use original spare parts and accessories only.
  • Do not subject the product to strong impacts, serious damages may result.
• Do not use near or under flammable materials (like curtains), heat, cold spots and steam.

GENERAL INFORMATION

• Place on flat and stable surface. Do not place on hot surfaces, or near to flames or heat sources.
• Before using the unit for the first time, clean the parts that will be in touch with food (filter, filter holder, container). Never leave the appliance unattended while it is running.
• Always pour the water before operating.
• Fill the tank with cold water, ensure to stay within the maximum capacity indicated on tank itself (MAX – 1.2L). During use do not go below MIN level.
• Use fresh and natural water, do not use hot or sparkling water, or liquids that may damage the machine.
• Do not switch on the product without water in the tank, as the pump may be damaged.
• Do not use outdoors, do not store in ambients with temperature lower than 0oC, as water residues may freeze and damage inner parts. NEVER insert in the filters for 1 or 2 cups anything else than powder coffee. Different substances may damage the product.
• Danger of burning: during erogation of hot water or of steam, do not direct the jet against yourself or other persons. Grab the steam erogation tube only from the rubber handle, grab the filter holder only  from the plastic handle: do not touch metal parts.
• If coffee doesn’t come out from the filter holder, the filter may be blocked. Remove the filter holder slowly to avoid splashes, and clean the parts as described afterwards.
• To move the machine, grab the fixed part of housing.
• Do not dismount the appliance.
• After use, it is suggested to switch off the product using the general switch button (on the side).
• Do not immerse in water or other liquids. In any case, avoid any splashing of water.

G10188 DESCRIPTION

1 Decorative bar| 2 Water container| 3 Erogation knob  4 Handle of erogation tube
---|---|---
5 Steam erogation tube| 6 Housing| 7 General switch    8 Cup warmer
9 1 cup button| 10 2 cups button| 11 Steam button     12 Termometer
13 Filter holder link| 14 Floater| 15 Grid                   16 Drip container
17 Measuring cup| 18 1 cup filter| 19 2 cups filer         20 POD filter
21 Filter holder| 22 Coffee spout|

ASSEMBLY

• Clean all the removable parts.

• Fill the container (2) with water without exceeding the MAX level, and Mount in its seat. To ensure the correct function, press down well the container.
  WARNING: Use fresh and natural water, do not use hot or sparkling water, or other liquids.

• Mount the drip container (16) on the front part of housing (6).

• Mount the grid (15) on the drip container (16).
  WARNING: Before switch on, verify that all the parts are properly mounted.

FIRST USE and INTERNAL CIRCUIT CLEANING

At the first use it is needed to perform the cleaning of internal water circuits.

Clean coffee circuit

• Insert the plug in the power socket and press button (7) to switch on. The lights of buttons twinkle to indicate that the appliance is heating, and then they stay on when the appliance is ready.
• Mount the filter holder (21) in its seat (13). Insert the filter holder in correspondence of symbol and  rotate clockwise to the symbol .
• Put a 250ml container on the grid (15) and press the 2 cups button (10 -).
• Empty the contianer and repeat operation.

Clean steam erogation circuit

• Put a 250ml container under the steam erogator.
• Rotate the knob (3) anti-clockwise, press button (9 – ) and let hot water come out for 30 seconds.
• The appliance is now ready to prepare the first coffee.
  WARNING: pay attention to not finish all water inside the container during these operations. WARNING: repeat these operations in case the unit is not used for several days.

OPERATION

• Mount the tank (2) in its seat. To ensure correct function, press down well the tank.
• Fill the tank (2) with water without exceeding level MAX, then close with the lid(1). WARNING: Use fresh natural water, do not use hot or sparkling water, or other liquids. MOUNT

FILTER IN THE FILTER HOLDER

The filters are equipped with a safety system that avoids accidental falling of the filter. To mount and dismount a filter, you have to align the parts identified with A (filter) and B (filter holder) in the picture on the side.

To mount a filter in the filter holder

• Take the filter grabbing in correspondence of the part A.
• Insert in the filter holder (21) the part of filter opposite to the part A.
• Lower the filter into the filter holder by aligning the parts A and B.
• To dismount the filter, align the parts A and B and pull the filter upwards.

THERMOMETER READING
The thermometer measures the temperature of the water inside the boiler. The colors on the dial are:

• White: heating phase
• ****: optimum temperature for espresso and hot water erogation
• Last 2 sectors: optimum temperature for steam erogation

MAKE COFFEE WITH POWDER

• Insert the plug in the power socket and press button (7) to switch on. The lights of buttons twinkle to indicate that the appliance is heating, and then they stay on when the appliance is ready.

• Select the desired filter, one or two cups (18 or 19), and insert in the filter holder (21).

• Pour 1 cup (17) not filled in case of 1 cup filter and press slightly with presser.

• Pour 2 cups (17) not filled in case of 2 cups filter and press slightly with presser.

• Mount the filter holder (21) in its seat (13). Insert the filter holder in correspondence of symbol and  rotate clockwise to the symbol . Place one or 2 coffee cups under the spout (22).

• Press button (9 – ****) for one cup of espresso or the button (10 – ) for two cups.

• The button twinkles. There is a short phase of water loading, then the coffee comes out from spouts (22).

• Once the desired quantity has been reached, press the flashing button again to stop dispensing.
  WARNING: do not remove the filter holder during function. At the end of erogation, wait 10 seconds before removing the filter holder. Remove slowly the filter holder to avoid splashing.

• At the end of dispensing, the lights remain on and you can make another coffee.

• If use is finished, turn off the machine with the button (7).
  WARNING: after use, do not leave the filter holder (21) inserted in its seat (13) in order to not damage the gasket present in the filter holder seat.

MAKE COFFEE WITH PODS

• Insert the plug in the power socket and press button (7) to switch on. The lights of buttons twinkle to indicate that the appliance is heating, and then they stay on when the appliance is ready.

• Select the POD pod filter (20), and insert in the filter holder (21).

• Insert a pod in the filter, and press it inside with your fingers. The pod must be well centered and pushed down well. If the external paper parts protrude from the filter, fold them inwards.
  WARNING: If the pod is not inserted correctly, or if the external paper parts are not folded well, the filter holder may not tighten, and drops may come out of the filter holder.

• Mount the filter holder (21) in its seat (13). Insert the filter holder in correspondence of symbol and  rotate clockwise to the symbol .

• Place one coffee cup under the spout (22). Press the button (9 – ****).

• The button twinkles. There is a short phase of water loading, then the coffee comes out from spouts (22).

• Once the desired quantity has been reached, press the flashing button again to stop dispensing.
  WARNING: do not remove the filter holder during function. At the end of erogation, wait 10 seconds before removing the filter holder. Remove slowly the filter holder to avoid splashing.

• At the end of dispensing, the lights remain on and you can make another coffee.

• When removing the filter holder, the pod may remain attached to the seat of the filter holder (13). To remove it, tilt the filter holder down, or remove it gently with a knife.

• If use is finished, turn off the machine with the button (7).

MAKE MILK FOAM FOR COFFEE

• Prepare coffee as described before, using an espresso cup if you want to prepare a macchiato, or a bigger cup if you want a cappuccino.

• Put whole milk in a stainless steel jug, filling one third of the capacity.

• Press steam button (11 – ). The light of steam twinkles to indicate that the appliance is heating, and then they stay on when the appliance is ready.
  CAUTION, Risk of burning: during steam erogation, do not direct the jet towards yourself or towards other people. Only handle the tube by the rubber part: do not touch metal parts.

• Direct the steam erogation tube (5) in an empty container, then rotate knob (3) anti-clockwise: some water will be released first and then steam. Stop steam jet rotating back the knob “0”.

• Direct the steam erogation tube (5) in the jug, immersing well the tube in the milk.

• Rotate knob (3) anti-clockwise: tube will start dispensing steam.

• During steam erogation, move and rotate the jug in order to let the jet arrive to all the milk.

• When you see foam in the jug, milk is frothed. Stop steam jet rotating back the knob “0”.

• Pour the foam of milk in the cup of coffee prepared before.
  WARNING: after every use of the tube (5), erogate steam for some seconds, in order to keep the steam tube clean of milk residues, and clean the tube (5) with a damp cloth.

LOWER THE TEMPERATURE AFTER USE OF THE STEAM JET
Steam requires a higher temperature respect to coffee. To prepare a coffee (or dispense hot water) after dispensing steam, the temperature has to be lowered.

• Press one of the coffee preparation buttons (9 – ****) or (10 – ). The lights of buttons twinkle to indicate  that the appliance is cooling, and then they stay on when the appliance is ready.
• To make the temperature go down more fastly, you have to release some steam.
• Direct the steam erogation tube (5) in an empty container, then rotate knob (3) anti-clockwise: water mixed with steam will be released.
• When the lights of buttons stop flashing and remain steady, the temperature has dropped sufficiently and the machine is ready to make coffee. Stop the steam by turning the knob to “0”.

DISPENSE HOT WATER

• Switch on the machine in coffee dispensing mode (with thermometer on ****).
• CAUTION, Risk of burning: during hot water erogation, do not direct the jet towards yourself or towards other people. Only handle the tube by the rubber part: do not touch metal parts.
• Direct the steam erogation tube (5) in a cup, then rotate knob (3) anti-clockwise and press the button (9 – ): hot water is released. When the desired amount of water has been obtained, stop water jet pressing the button (9 – ) and rotating back the knob on “0”.

EMPTY CONTAINER AND EVENTUAL PUMP BLOCK
Please avoid to finish water in the container, but in case it happens:

• When the water runs out, the machine makes a loud and unusual noise. Turn off immediately and pour water in the tank. At the next restart, the pump may not load the water correctly. To help fill the water it is recommended to dispense hot water from the tube (5).
• Direct the steam erogation tube (5) in a cup, then rotate knob (3) anti-clockwise water or steam is released. Stop steam jet rotating back the knob “0”.

FUNCTIONS

REGULATION OF COFFEE EROGATION TIME

To change the coffee erogation time of one of the two buttons (9) or (10), follow this procedure:

• Place one or 2 coffee cups under the spout (22).
• Select the button (9 – ****) or (10 – ) for which you want to change the erogation time, and keep pressed  until the erogation starts.
• Stop pressing when erogation starts, and press again when you reach the desired quantity of coffee in the cup. At following operations, the machine will change the erogation time as for new setting.

STAND-BY, AUTO-OFF, OFF

• To limit energy consumption when not in use, this machine has 3 functions.
• Function Stand-by: for 30 minutes from the last use, the machine remains in stand-by and keeps the water at the right temperature, ready to make coffee.
• Function Auto-Off: 30 minutes after the last use, the machine turns off automatically. To make a coffee, press one of the coffee preparation buttons (9 – ****) or (10 – ). The lights of buttons twinkle to indicate that  the appliance is heating, and then they stay on when the appliance is ready.
• Function OFF : he machine can be turned off at any time by pressing the main switch (7).
• CLEANING – Unplug the power cord from the electrical outlet and allow the unit to cool down before cleaning. Do not wash parts of the appliance in the dishwasher.
  The machine must be cleaned regularly and daily, to keep it efficient and to extend the life of the appliance.

HOUSING and TANK
Clean the fixed parts of housing (6) with a soft damp cloth. Do not immerse the main body in water. In any case, avoid splashing water or other liquids from reaching those parts. Periodically clean the tank (2) and the lid (1) with a soft sponge and dish detergent. Rinse and dry well before reassembling them.

GRID AND DRIP COLLECTING CONTAINER
Remember to empty the container (16) at least once a week. There is also a floater (14): if the floater comes out of the grid (15), the tray is too full and must be emptied.
Periodically clean the grid (15) and the drip tray (16):

• Disassemble these parts and empty the container (16).
• Wash with a soft sponge and dish detergent. Rinse and dry well before reassembling them.

FILTERS (18 – 19 – 20)

• With use, the filter holes could become clogged. Visually check that they are free.
• If they are clogged, put the filter in the filter holder and assemble the machine without adding the coffee. Press the 2 cups button (10) to dissolve impurities and coffee residues.
• If you notice formation of limescale, immerse the filters in a solution of water and vinegar and leave to act for 6 hours. Afterwards, wash the filters with dish detergent, rinse and dry.

SEAT FOR LINKING THE FILTER HOLDER (13)

• WARNING: after use, do not leave the filter holder (21) inserted in its seat (13) in order to not damage the gasket present in the filter holder seat.
• With use, impurities and coffee residues may form even in the seat of the filter holder (13).
• Periodically check the condition of this part, and if you notice any impurities, proceed with cleaning. Use a soft sponge, unlock the holes gently with a needle and dispense hot water without mounting the filter holder (put a large cup underneath and press the 2 cups button, repeat 2 more times).

STEAM EROGATION TUBE (5)
CAUTION: clean the tube wand only when it is cold.
After each use of the tube (5), dispense steam for a few seconds to clean it of milk residues, and clean the tube with a damp cloth. At least once a month, clean the parts of the dispenser:

• Remove the tube (5) downwards. Remove the silicone handle (4) by pulling it downwards.
• Clean the internal steam tube with a damp cloth.
• Periodically clean the tube (5) and handle (4) with a soft sponge and dish detergent. Rinse and dry well before reassembling them

DECALCIFICATION

Cleaning the coffee machine is necessary to make it work efficiently. Despite this, depending on the water used and especially if you use hard and calcareous water, it is possible that limescale deposits and impurities may form, compromising the functionality of the appliance.
In this case it is necessary to descale the internal circuits. To do this, use a specific descaling product for coffee machines, easily available in specialized shops and service centers. CAUTION: the manufacturer assumes no responsibility for damage to the machine caused by the use of non-compliant products. The coffee maker needs decalcification every 3 months:

1. Put a filter in the filter holder and mount it to the docking place without adding the coffee.

2. Fill the container by mixing water and descaler, in the doses indicated in the descaler pack. Fill up to the MAX level.

3. Place a 250ml container on the grid (15) and press (10 – ).

4. Empty the container and place it under the steam erogator.

5. Turn the knob (3), press (9 – ****) and let the hot water flow out for 30 seconds. Wait 5 minutes.

6. Empty the container and repeat steps 3, 4 and 5 until the water in the tank runs out.
   At this point it is necessary to rinse the internal circuits to eliminate eventual residues of descaler:

7. Remove the tank (2) and wash it with a soft sponge and dish detergent.

8. Fill the tank with fresh water and put it back on the coffee machine.

9. Place a 250ml container on the grid (15) and press (10 – ).

10. Empty the container and place it under the steam erogator.

11. Turn the knob (3), press (9 – ****) and let the hot water flow out for 30 seconds. Empty the container.
    The machine is now ready to prepare coffee again.

TROUBLE SHOOTING

Problem| Cause| Solution|
---|---|---|---
No steam is generated| Temperature not correct| Wait steam indicator light stop flashing.|
Tank is empty / not well inserted| Fill the tank / Insert well the tank pressing down|
Steam nozzle clogged| Remove erogation tube (5).
With a needle, remove any encrustations in the steam outlet hole. If the problem persists, perform descaling.|
| Too much powder in the filter and| Turn off the machine and wait for it cool down,|
Coffee runs| | clean the seat of filter holder as described in|
| “Cleaning” section.|
out around the| There is powder in the seal ring of|
edge of the| the seat of filter holder| When using agin, pour less coffee in the filter.|
filter holder| Filter holes are blocked| Clean the filter|
| Filter holder not linked well| Make sure to fix well the filter holder.|
| Tank is empty / not well inserted| Fill the tank / Insert well the tank pressing down|
Coffee comes| Coffee powder is too pressed| Press the coffee powder less|
Coffee powder is too fine| Use thicker coffee powder|
out too slow|
Too much coffee in the filter| Insert less coffee|
or no coffee|
Filter holes are blocked| Clean the filter|
comes out|
The holes of the water exit in the| Switch on without filter holder and let water|
| seat of filter holder are blocked| come out. If problem persists, perform descaling.|
Water leakage| Drip tray is filled up| Please clean the drip tray|
on the bottom of machine| Water tank is not mounted well| Insert well the tank pressing it down
---|---|---
Strong and unusual noise| Water tank is empty and pump cannot take water| Pour water in water tank
The steam cannot froth.| Temperature not correct| Wait steam indicator light stop flashing.
Used skimmed milk| Use whole milk

TECHNICAL FEATURES

• Power supply: AC 220-240V ~50-60Hz. Power: 950W
• 15 Bar, pump ULKA
• 3 filters: pods, powder 1 or 2 cups
• Milk frother, Cup warmer, Thermometer

WASTE OF ELECTRIC AND ELECTRONIC EQUIPMENT
The product is made of non-biodegradable and potentially polluting substances if not properly disposed of; other parts can be recycled. It’s our duty to contribute to the ecological health of the environment following the correct procedures for disposal. The crossed out wheelie bin symbol indicates the product complies with the requirements of the new directives introduced to protect the environment (2002/96/EC, 2003/108/EC, 2002/95/EC, 2012/19/EC) and must be properly disposed at the end of its lifetime. If you need further information, ask for the dedicated waste disposal areas at your place of residence. Who does not dispose of the product as specified in this section shall be liable according to the law.

To find the nearest service center, please call the telephone number 0541 694246, fax number 0541 756430 or contact us at assistenzatecnica@trevidea.it asking for the service centers supervisor.

Appliance is conform to the pertinent European regulation and is therefore marked with the CE mark.

www.g3ferrari.it TREVIDEA S.r.l.
TREVIDEA S.R.L. – Strada Consolare Rimini – San Marino n. 62 – 47924 – RIMINI (RN) – ITALY
MADE IN CHINA

Documents / Resources

| G3FERRARI G10188 Espresso Maker [pdf] User Manual
G10188, G10188 Espresso Maker, Espresso Maker, Maker
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>