ifi audio 246GOBAR GO Bar Portable USB DAC Headphone Amplifier Owner’s Manual
- June 4, 2024
- iFi Audio
Table of Contents
ifi audio 246GOBAR GO Bar Portable USB DAC Headphone Amplifier
Thank you for purchasing the barfrom the GO series. The bar is a balanced USB audio DAC amplifier.
Audio format, frequency and sound effects LED
The LED Ccolour scheme indicates the current sampling frequency and audio format received by the GO bar from the music source. Sound effect modes ara also indicated.
LED Mode
- White 44.1/48kHz
- White 88.2/96kHz
- White 176.4/192kHz
- White 352.8/384kHz
- White DSD 64/128
- White DSD 256
Sound effects
LED Status
- Blue XSpace
- Orange XBass
Tip: Sonically-hindering DSP is NOT used for XBass+ nor XSpace systems. They use the highest-quality discrete components and operate purely in the analogue domain. Hence all the clarity and resolution of the original music is retained.
MQA and Digital filter LED
- MQA: Green
- MQA Blue
- MQA Studio Magenta
Original Sample Rate
- LED Mode
- Cyan BP
- White GTO
- Red STD
- Yellow MIN
- Off DSD playback
iEMatch switch
iEMatch reduces the output level, so that even the most sensitive In-Ear-
Monitors (IEMs) can be matched to the GO bar.5mm headphones
Tip:
The G0 bar and/or the headphone will not be damaged if the iEMatch switch is
adjusted incorrectly, but the attenuation level will not be correct.
Volume control and gain
To increase volume, press the + button, and to decrease it, press the button.
Volume level is briefly displayed on the GO bar while pressing one of the
volume buttons, shown by the number of white LEDs on at a time -from none to
6. The increase or decrease of volume can be synchronised with the volume of
the mobile phone/computer. The connected device will indicate a change of
volume on its display if synchronisation is on, and the device’s volume
controls can additionally be used to adjust volume. The GO bar’s volume
buttons are still operational. By default, the synchronisation feature is off.
To switch this on or off, press the settings button (5) for > 8s. On is
indicated by the 6 white LEDS switching on in sequence from LED 1 and 6 to the
centre. Off is indicated by the 6 white LEDs switching off in the opposite
direction. Turbo Mode increases the gain by 6dB. To switch this on or off,
press the +and – volume buttons together for 2 25. Turbo Mode on is indicated
by 2 white LEDs increasing to 6 lighting up at the same time for 2s. Normal
gain is indicated by 6 white LEDs diminishing to 2 lighting up for 2s.
Tip:
For sensitive headphones and earphones, leave Turbo Mode off. For less
sensitive headphones, it may be appropriate to switch Turbo Mode on.
Settings and Digital filter mode
This button cycles between: Off> XSpace > XBass+> XSpace and XBass+ (short
click). Please refer to item 1 for sound effects LED indications. Digital
filter setting mode (long press 22s). Please see below.
Digital filter
To enter digital filter setting mode, press and hold the button for 23s.The
MQA LED will flash with the currently set digital filter colour (as shown in
item 2). Press the + or – buttons (4) to change the filter selection. A short
press on the settings button (5) will select and exit the filter setting mode.
The following 4 digital filters are available:
- BP (Cyan) Bit-Perfect: no digital filtering, no pre or post ringing
- Standard, modest filtering, modest pre and post ringing ‘STD’ (Red)
- MIN’ (Yellow) Minimum phase, slow roll-off, minimum pre and post ringing
- GTO’ (White) Gibbs Transient-Optimised: upsampled to 352/384kHz, minimum filtering, no pre ringing, minimum post ringing
- Note:If the GTO filter is selected, the only sample rate indicator showing will be 352.8/384kHz, indicating the upsampling operation of this filter.
Balanced 3.5mm headphone output
For connecting 3.5mm headphones. This is a single-ended output.
Balanced 4.4mm headphone output
For connecting balanced 4.4mm headphones. This is a fully balanced output.
USB-C input
The USB-C socket plays up to 32-bit 384kHz, has full MQA decoding, and native
DSD up to DSD256.
Tip:
When the phone battery is low (<30%), the Go bar on olderiPhones (65or before)
may not be able to operate.
Warning:
Ifthe GO bar’s volume synchronisation function is on, and the music source is
Tidal via Windows, please ensure that the Tidal setting of Forced Volume is
off. With this function on, there is no volume controlpossible, and the volume
will be at maximum. This has the potential to damage the connected headphone
and/or your hearing.
Specifications
- input:USB-C
- Formats: PCM
- 44.1/48/88.2/96/176.4/192/352.8/384kHz
- DSD2.8/3.1/5.6/6.1/11.3/12.3MHz
- DXD 352.8/384kHz
- MOA Full Decoder
- DAC: Bit-Perfect DSD & DXD DAC by Cirrus Logic
- Headphone Outputs: <0.00296 (6.5SmW/2.0V @ 6000)
- Balanced: 4.4mm
- UnBAL: 3.5mm
- Power Output: 475mW@320;7.2V@6000
- Balanced:
- UnBAL: 300mW@320;3.8V@6000
- Output Impedance
- Balanced:<10
OVERVIEW
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>