Anker PowerConf A3301 User Manual

USER MANUAL

Anker PowerConf A3301

Anker Innovations Limited. All rights reserved. Anker and the Anker logo are trademarks of Anker Innovations Limited, registered in the United States and other countries.
Model: A3301

At a Glance

1. Multi-function button
2. Volume down button
3. Mute button
4. Phone call button
5. Volume up button
6. LED light bar
7. Power LED
8. Power button
9. Bluetooth button
10. Bluetooth LED
11. USB port (Type-A) for charge out
12. Audio output port
13. USB power port (Type-C) for charge in

Connecting

• Connect to your computer by using a USB cable.

• Connect to your computer or mobile device via Bluetooth pairing.
• Power on the product for the first time, it will automatically enter Bluetooth pairing mode.

Bluetooth LED behavior

• Each time you power on the product, it will automatically connect with the last successfully connected device if available.
• To disconnect Bluetooth, press the Bluetooth button again.

Powering On / Off

Press and hold the power button for 2 seconds to power on. The LED light bar will light on clockwise and then fade out. To power off, press and hold the power button for 2 seconds.

Power LED behavior

• Once connected to your computer, it will automatically power on.
• Once connected to power by using a power adaptor (not provided), it will automatically power on.
• It will automatically power off after 30 minutes of inactivity or no source.

Button Controls

Light Bar Behaviors

Charging

• Charging this product

Power LED behavior

Charging an external device

• When powered off or being charged, it won’t charge out.
• When the remaining battery is less than 30%, the charge out current will be 5V …0.5A; if less than 10%, it won’t charge out.

Audio Output

Connect an external speaker to the AUX jack of this product by using an AUX cable (not provided). The audio will be played through the speaker.

Specifications

Specifications are subject to change without notice.

Important Safety Information

• Avoid dropping.
• Do not disassemble.
• Do not install near any heat sources.
• Do not place any sources of danger on this device (e.g. liquid filled objects, lit candles).
• Use original or certified cables.
• Clean with a dry, soft lint-free cloth. Do not use any corrosive  cleaner or oil.
• Do not expose batteries to high heat as direct sun light, fire and or the like.

Notice

This product complies with the radio interference requirements of the European Community.

Declaration of Conformity

Hereby, Anker Innovations Limited declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU.For the declaration of conformity, visit the Web site: www.anker.com.

Due to the used enclosure material, the product shall only be connected to a USB Interface of version 2.0 or higher.
Do not use the Device in the environment at too high or too low temperature, never expose the Device under strong sunshine or too wet environment.

The suitable temperature for the product and accessories is -10~40℃.
When charging, please place the device in an environment that has a normal room temperature and good ventilation.

It is recommended to charge the device in an environment with a temperature that ranges from 5℃ ~25℃ .

RF exposure information: The Maximum Permissible Exposure (MPE) level has been calculated based on a distance of d=20 cm between the device and the human body. To maintain compliance with RF exposure requirement, use product that maintain a 20cm distance between the device and human body.

CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.

Bluetooth Operating Frequency Range ：2402~2480MHz; Bluetooth Max Output Power:8dBm(EIRP)

The following importer is the responsible party (contact for EU matters only)
Importer: Anker Technology (UK) Ltd
Importer Address: Suite B, Fairgate House, 205 Kings Road, Tyseley, Birmingham, B11 2AA, United Kingdom.

This product is designed and manufactured with high quality materials and components, which can be recycled and reused.

This symbol means the product must not be discarded as household waste, and should be delivered to an appropriate collection facility for recycling. Proper disposal and recycling helps protect natural resources, human health and the environment. For more information on disposal and recycling of this product, contact your local municipality, disposal service, or the shop where you bought this product.

FCC Statement

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

(1) Reorient or relocate the receiving antenna. (2) Increase the separation between the equipment and receiver. (3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. (4) Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

The following importer is the responsible party
Company Name: Fantasia Trading LLC
Address: 9155 Archibald Avenue, Suite 202, Rancho Cucamonga, CA, 91730, US
Telephone: +1 (800) 988 7973

Radiation Exposure Statement

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Trademark

Bluetooth

The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by Anker Innovations Limited. is under license.

Other trademarks and trade names are those of their respective owners.

* Additional Legal Rights for Consumers

For consumers, who are covered by consumer protection laws or regulations in their country of purchase or, if different, their country of residence, the benefits conferred by Soundcore’s Limited Warranty are in addition to all rights and remedies conveyed by such consumer protection laws and regulations, including but not limited to these additional rights. For FAQs and more information, please visit https://www.soundcore.com/

CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.

IC NOTICE TO CANADIAN USERS

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

This Class B digital apparatus complies with Canadian ICES-003.

IC RF Statement:

When using the product, maintain a distance of 20cm from the body to ensure compliance with RF exposure requirements.

Anker-PowerConf-A3301-Manual-Optimized.pdf

Anker-PowerConf-A3301-Manual-Orginal.pdf

Questions about your Manual? Post in the comments!

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>