HOMCOM 824-076V90 Tower Fan Instruction Manual
- June 4, 2024
- HOMCOM
Table of Contents
HOMCOM 824-076V90 Tower Fan
IMPORTANT SAFETY INFORMATION
IMPORTANT , RETAIN FOR FUTURE REFERENCE: READ CAREFULLY.
READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE PRODUCT DESCRIBED. PROTECT YOURSELF AND OTHER BY OBSERVING ALL SAFETY INFORMATION. FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE !
-
Read all instructions carefully before using the FAN.
-
Use this FAN only as described in this manual. Any other use not recommended by th manufacturer may cause fire, electrical shock, or injury to persons.
-
Remove the package and ensure that the FAN is undamaged. In case of doubt do not use FAN and contact with your supplier.
-
Do not let children play parts of package.
-
Before use the FAN, check if the voltage marked on the rating label corresponds to the mains in your home.
-
Extreme caution is necessary when the FAN is used by or near children or Invalids and whenever the FAN is left operating unattended.
-
Avoid using extension cord as the extension cord may overheat and cause a risk of fire.
-
Do not pull the power cord to disconnect with power source. Always grasp the plug to pull out.
-
Do not insert any objects into the FAN as it may cause an electric shock or injure or damage to the FAN. Do not block or tamper with the FAN in any manner while it is in operation.
-
Do not leave the FAN unattended.
-
This FAN is not intended for use in wet or damp locations. Never locate a FAN where it may fall into a bathtub or other water container.
-
Do not use FAN outdoors.
-
Disconnect the fan from the mains power when not in use, and before servicing or performing any maintenance.
WARNING : The Main Power Switch and the On/Off switch should not be used as the sole means of disconnecting power. Always unplug the power cord before servicing or moving the unit. -
Keep the fan clean and maintain in good condition (use an authorized service agent).
-
Use recommended parts only (non genuine parts may be dangerous, and will invalidate your warranty).
-
When not in use store in a safe, dry, childproof location.
-
This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
-
The back housing shall not dismantle, removal will be dangerous .
-
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
-
Children should be supervised to ensure that they do not play with the appliance.
WARNING : To avoid danger of electric shock, unplug from outlet when not in use and before cleaning. If the supply cord is damaged, it must be replaced by the manufactory or it’s service agent or a similarity qualified person in order to avoid a hazard.
PARTS NAME
ASSEMBLY
-
Take out the two parts of the base from packing box. Then, align the centers of the two parts of the base and place them in a crossed form. Rotate one of the two bases to align its hole site and make it stuck correctly. (Fig 1)
-
Put the wire in the recess, then fix the base on the fan body with four screws (included), and turn the screws clockwise. (Fig 2)
REMOTE CONTROL
- Included a button cell battery (the type of battery CR2025). Storage the remote control at the back of fan.
- The Remote Control Power button is labeled as such(Fig 3). All the functions performed with the Remote Control work identically to the Manual Controls.
OPERATION
The FAN may be operated by the manual controls located on the FAN (Fig 4) or by your remote control. (Fig 3)
-
Place the FAN on a stable flat surface. Plug the cord set into a 220-240V~ electrical outlet.
-
POWER : Turn the FAN on by pressing the ‘POWER’ button; Turn the FAN off by pressing the ‘POWER’ button again.
-
SPEED
: You can adjust the fan speed to the desired level: low, medium, or high by pressing ‘SPEED’. The speed setting is displayed on the LED display. (Fig 5) -
MODE : Pressing the ‘MODE’ button will set the FAN into NORMAL, NATURAL, SLEEP and CHILD mode.
- NORMAL Mode : Fan will start work at any speed you set up.
- NATURAL Mode : Fan will start work at low speed(5s)→medium speed(5s)→high speed(5s)→medium speed(5s), it works as per this recycle.
- SLEEP Mode : 1）If you set the mode at high speed, fan will work at high speed at 30 mins, then transfer to medium speed at 30 mins and transfer to low speed until fan stop working. 2）If you set the mode at medium speed, fan will work at medium speed at 30 mins, then transfer to low speed until fan stop working. 3）If you set the mode at low speed, fan will work at low speed until fan stop working. The LED display will turn off if you don’t control the fan in 30 seconds, touch any button to turn on the display.
- CHILD Mode : Fan will auto. Set up timer at 3 hours, oscillation function will start. And it will work at high speed at 15 minutes, transfer to medium speed at 15 minutes, then transfer to low speed until it take off. You can take off oscillation function by manual. The LED display will turn off if you don’t control the fan in 30 seconds, touch any button to turn on the display.
- NORMAL Mode
-
TIMER : The fan is equipped with a timer that allows you to set its length of operation from 1 hour to 12 hours. The LED display will turn off if you don’t control the fan in 30 seconds, touch any button to turn on the display.
-
OSCILLATION : Pressing the ‘OSC’ button will start and stop the oscillation function. The symbol is displayed on the LED display.
-
DISPLAY : Can be switched off temporarily by press the LED button on the remote or by pressing and holding the SPEED button on the control panel for more than 3 seconds, the display will light up again once any control button is activated.
-
CABLE HOOK : The cable hook is packed in the user manual, take it out and install on the back side of the fan. The power cord can be hanged at the cable hook when the fan is not in used. (Fig 6)
MAINTENANCE
- This can only be done by an authorized service agent such as your local dealer or any agent qualified to undertake electrical repairs.
- If the unit requires external cleaning make sure it is switched off and unplugged from the mains supply. Use a soft tissue or cloth for general cleaning. To remove more persistent dirt or grime wipe down with a cloth that has been dampened with warm soapy water. Do not use any solvents ( such as thinners ) as these may damage the plastic casing.
Correct Disposal Of This Product
This marking indicates that this product should
not be disposed with other household wastes throughout the EU. To prevent
possible harm to the environment or human health from uncontrolled waste
disposal, recycle it responsibly to promote the sustainable reuse of material
resources. To return your used device, please use the return and collection
systems or contact the retailer where the product was purchased. They can take
this product for environmental safe recycling.
Customer Support
0039-0249471447
clienti@aosom.it
IMPORTATO DA:
AOSOM Italy srl
Centro Direzionale Milanofiori
Strada 1 Palazzo F1
20057 Assago (MI)
P.I.: 08567220960
FATTO IN CINA