KOSUMOSU B0BR156SYZ 3D LED Digital Wall Clock User Manual

KOSUMOSU B0BR156SYZ 3D LED Digital Wall Clock

Thanks for choosing our product, Please read the user manual carefully before using the led clock.

Brightness setting

Brightness setting (Brightness Dimming)

• Press the “BRIGHT” button to switch the brightness dimming in sequence for ” High – Medium- Low -Auto “.
• There are 8 levels of brightness dimming for “Auto” mode, which will be dimming automatically according to the ambient light via the built-in light sensor.
• Press the “Display on/off ” button @ to turn on or off the LED light. (* It is NOT equivalent to shutting down the clock!)

Temperature display

• Press the “TEMP” button to show the Temperature in °C for ° 5 secs., or press it again to show it in back-to-clock mode automatically.

Loop display
Press the button to turn on/off the Loop Display of the “lime”, ”Temperature” and “Date”.

Power Supply

• This LED clock needs a plug-in USB power supply (5V/1A).
•  AC adapter is NOT included, please use a compliant adapter.

Remote Control Buttons

Function

Time/Date/Year setting

1. Press the “CLOCK” button to enter the time setting, and the Hour numbers start to flash, then press the button to adjust the hour, after that press the button and skip to set the minutes.
2. Adjust the minutes via the button, finally, press the “CLOCK” button to confirm the time setting and skip to the Date setting.
3. Then adjust the month and day numbers via these 4 arrow buttons as above, and press the “CLOCK” button to confirm date setting and skip to Year setting.
4. Adjust the Year numbers via the button, finally press the “CLOCK” button to confirm the setting and back to time mode.

12/24 Hours System

• Press the button to switch the 12/24-hour time system.

Seconds flashing

• Press the button to turn on/off the two flashing second points between the hours and minutes.

Alarm setting

1. Press the “ALARM” button twice to enter the Alarm setting, press the button to switch the Hour or Minute setting, and then adjust data via the button.
2. Press the “ALARM” button to confirm the alarm time.
3. Press the button to set the alarm clock “ON” or “OFF”.
4. Finally, press the “ALARM” button to confirm and back to clock mode.

In clock mode, press the “ALARM” button, and it’ll show the preset alarm time, or if the alarm was turned off, it’ll show “OFF”.

Snooze

• This LED clock was a preset Snooze function, which means the bell will ring 3 times at 5 minutes intervals, and 1 minute per ring.
• When the bell rings, you can press the “ALARM” button to pause ringing and delay the alarm for 5 minutes.
• When the bell rings, you may press any buttons besides the “ALARM” button to stop ringing right away.
• If you want to close the alarm entirely, please set the alarm OFF as above Alarm Setting descriptions.

Brightness setting (Brightness Dimming)

• Press the “BRIGHT” button to switch the brightness dimming in sequence for ” High – Medium- Low -Auto “.
• There are 8 levels of brightness dimming for “Auto” mode, which will be dimming automatically according to the ambient light via the built-in light sensor.
• Press the “Display on/off ” button @ to turn on or off the LED light. (* It is NOT equivalent to shutting down the clock!)

Temperature display
Press the “TEMP” button to show the Temperature in °C for ° 5 secs., or press it again to show it in back-to-clock mode automatically.

Loop display
Press the button to turn on/off the Loop Display of the “lime”, ”Temperature” and “Date”.

Hang on the wall (desk clock/wall clock)

• This LED clock may be used as a desk clock with an attached base bracket and also can be hung up on the wall with an included installation kit.

Button Operations

1. Press the “SET” key to enter the time setting.
2. Press the “SET” key again to switch between hours, minutes, months, days and years, and adjust these dates via the “*” or “-” key, then press the “SET” key to confirm the setting.

Alarm setting

1. In clock mode, long press the “SET” key for 3 seconds. to enter into the alarm setting, the HOUR numbers will flash.
2. Adjust the Hour by the “+”/ “-” key, then press the “SET” key and skip to the minute numbers, to set via the “+”/ “-” key.
3. Press the “SET” key to confirm the alarm time, then press the “-” key to turn ON or OFF the alarm clock.
4. Finally, press the “SET” button to confirm the alarm setting and back to clock mode.

In clock mode, press the “+” key, and it will show the alarm time, or if the alarm was turned off, it will show “OFF”.

Other settings

• In clock mode, long press the “+” key for 3 seconds. to turn on/off the two flashing second points in the middle.
• Long press the “+” key for 6 seconds. on the back of the clock to turn on/off the Loop Display of “Time”, “Temperature” and “Date”.
• Press the “key to show the Temperature in C for 5 secs., or press it again to show it in F for 5 secs., then back to clock mode automatically.
• In clock mode, long press the “key for 3 secs. to set the brightness dimming in sequence for ” High – Medium – Low – Auto”.

Specifications

• Input: 5V/1A (*AC adapter is not included)

Warning

• This LED clock needs a plug-in USB power supply.
• ONLY use a safe and compliant power adapter(5V/1A), so that the power supply voltage is stable and the clock works normally.

Package Content

• Digital Led clock x 1
• Base bracket x 1
• Plug in USB cable x 1 (* AC adapter is not included)
• Remote control x 1
• Installation kit x 1

CONTACT

Any problem, please

• support@sz-krs.com.cn. with the order number and detailed problem

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>