Ovation OP-24 Plus Preamp Acoustic Electric Guitar Owner’s Manual

June 4, 2024
Ovation

Ovation OP-24 Plus Preamp Acoustic Electric Guitar

Specifications

  • Model: OP-24 Plus preamp

  • Features: Studio quality contemporary acoustic/electric guitar
    sounds, three-and-a-half band graphic equalizer

  • Output: 1/4 Hi-Z unbalanced phone jack

  • Power: 9V Battery

Product Usage Instructions

  1. Preamp Features & Functions
    The OP-24 Plus preamp offers a wide range of studio-quality acoustic/electric guitar sounds with exceptional control and sonic flexibility. The circuitry is designed to be quiet with minimal coloration added to the sound.

  2. Connections
    Connect your guitar to audio equipment using the 1/4 Hi-Z unbalanced phone jack output located near the endpin of the guitar. This allows you to connect to amplifiers, mixers, and effects.

Hi-Z Connection
For high impedance (Hi-Z) acoustic guitar amps or mixers, use a standard shielded 1/4 guitar cable inserted into the 1/4 jack on the guitar. The preamp can drive most audio equipment with rated inputs down to about 1000 Ohms.

Operation
Ensure a fresh 9V battery is installed correctly in the battery compartment. Inserting a 1/4 shielded guitar cable into the jack activates the electronics. The tuner operates without plugging in.Connect to a PA or acoustic guitar amp for optimal performance.

  • OP-24 PLUS PREAMP
  • OP-24 PLUS PREAMP
  • OP-24 PLUS PREAMP
  • OP-24 PLUS PREAMP
  • OP-24 PLUS PREAMP
  • OP-24 PLUS PREAMP
  • OP-24 PLUS PREAMP
  • OP-24 PLUS PREAMP
  • OP-24 PLUS PREAMP
  • OP-24 PLUS PREAMP
  • OP-24 PLUS PREAMP

INTRODUCTION

Congratulations and thank you for selecting an Ovation Acoustic/Electric guitar equipped with the OP-24Plus preamp. Please read this brief manual thoroughly to insure you get the best performance from your new Ovation.
The Ovation OP-24 Plus preamp access a wide range of „studio quality“contemporary acoustic/electric guitar sounds offering a player tremendous control and sonic flexibility. The circuitry is exceptionally quiet and adds no unwanted coloration.
Referring to fig. 1, you ll see the layout and nomenclature associated with the control features if these unit.

PREAMP FEATURES & FUNCTIONS

The preamp audio circuitry is whisper with very low distorion. (see specifications table) Tone control is greatly enhanced with a „three- and-a-half“ (we‘ll talk about that later) band graphic equalizer. Moreover, you can connect your guitar to a wide range of audio amplifier and recording equipment with the preamp standard 1/4“ Hi-Z, unbalanced phone jack output.
CONNECTIONS
Near the endpin of a guitar featuring these preamps, you‘ll notice a 1/4“ phone jack. This jack provides the signal from the preamp to any of a number of audio devices. mixers, effects, amps.

THE HI-Z CONNECTION
To connect your guitar to any high impedance (Hi-Z) acoustic guitar amp or mixer, use a standard, shielded, 1/4“ guitar cable inserted into the 1/4“ jack on the guitar. The preamp will drive most audio equipment with rated inputs down to about 1000 Ohms (this mean you can connect to almost anything). If you have a battery installed in the guitar, you‘re ready to play.

OPERATION
Make sure a fresh 9V battery is installed into the battery compartment of your guitar. The battery will fit only one way to assure correct polarity. Plugging a 1/4“ shielded guitar cable into the jack on the guitar activates the electronics in your guitar. Please note that the tuner will operate without „plugging in.“ After connecting the guitar, plug into a PA or acoustic guitar amp for best results.

CONTROLS

Please refer again to figure .1 to help yourself associate control names with their functions.

  1. Ovation-OP-24-Plus-Preamp-Acoustic-Electric-Guitar-VOLUME
    This slide control allows you to set the output level of the preamp.
    Moving the slider toward the top increases the output level. The OP-24 Plus can output a very potent signal, so be careful not to „overdrive“ your amp or mixer. If you notice any unwanted signal coloration, just reduce the output level of the guitar with this control.

  2. BATTERY LOW
    The indicator performs two functions. First, when you plug in a cable to the output jack, it will flash briefly to indicate that a battery is present. If no flash is evident, your battery is either dead or not installed. Secondly, this indicator will illuminate (and stay on), if the voltage of battery installed in the guitar dips be low about 7 volts. Replace the battery as soon as possible. With average use, expect about 100 hours of operation per battery.

  3. EQ Controls
    The EQ section allows you to accent or attenuate certain frequency bands within the guitar‘s audio spectrum. When all of the controls are in the center (detent) position, signals pass through the circuit unaltered.

    • Raising an EQ knob above the center  position increases the energy contained within that spectrum. Likewise, moving the control below the center position decreases the signals within that band.
    • The OP-24Plus preamp offers ± 12dB control simultaneously over three discrete ranges of the guitar‘s sonic spectrum. In addition, with the Mid-Shift switch, you can change the center frequency of the Mid EQ control by roughly one octave.
    • The Low EQ control allows you to increase or reduce the sound in the bass region. Raise this control above the center position to add fullness or bottom to your sound. De-emphasizing this band results I a lighter, less ponderous sound quality.
    • The High EQ control performs similarly to the „Low“ control except that its effect sha-pes the high frequency, or treble band. Increase this control for bright or airy sounds, or decrease for darker or round tonalities.
    • Much like the High and Low controls, The Mid-band control adds coloration to one of two user-selectable midrange frequencies. With the Mid-shift switch in the 400Hz position(down), the mid EQ is effective controlling „nasal“ tone qualities while in the 1KHz position, the mid control can add punch in upper mids or help „round off“ the attack present in this frequency spectrum.
  4. EQ In/Out
    This push-button enables you to engage or defeat the EQ section. When the switch is in the depressed position, the EQ is active.

  5. Mid-Shift
    As discussed above, this switch allows you select the center of the frequency band in which you would like th Mid control to operate.

  6. Pre-Shape
    By engaging this control (switch in the „down“ opsition), you add a fixed EQ curve on the sound from the pickup. Technically speaking, when the pre-shape circuit is in operation, the bass and treble frequencies are enhanced while at the same time, mid range response is attenuated. This pre-emphasis can be used alone, or with any other EQ setting you „Dail in“ with the three EQ controls.

Specifications

Current Draw| 5mA @ 9VDC
Flat Ref. Level| -7.5dB
Freq. Response| 20Hz~20KHz (±0.5dB)
S/N Ratio| 91dB (EQ bypass)

89dB (EQ in w/flat setting) 84dB (EQ in w/max setting)

Low EQ| ± 13dB @ 80Hz
Mid EQ| ± 12dB @ 400Hz

± 6dB @ 1KHz

High EQ| ± 12dB @ 10kHz
Output| Max. Level @ 10k Ohm 4Vp-p (1.4Vrms)
T.H.D| < .28% @ 500mV input
Low Battery| 7.5V

6 GEWEN | OP-2A music GmbH | Oelsnitz4 Plus preamper Str. 58 | 08626 Adorf / Germany

ovationguitars
ovationguitarsofficial
ovationguitarsofficial
// ovationguitars.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals