SRAM 95-3018-042-000 Karoo Hammerhead Instruction Manual

: June 1, 2024
: SRAM

Table of Contents

SRAM 95-3018-042-000 Karoo Hammerhead
Product Usage Instructions
FAQ
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

SRAM 95-3018-042-000 Karoo Hammerhead

SRAM 95-3018-042-000-Karoo-Hammerhead-product

Product Specifications:

Model : PMN
FCC ID : HIDF16000136
IC : D A107248
TRA Dealer No: DA51171/16

Product Usage Instructions

Installation:

Identify the specific component based on the model number.
Follow the manufacturer’s guidelines for installation.
Ensure proper connection and alignment of the product.

Operation:

Ensure the device is powered on.
Refer to the user manual for specific operation instructions based on the component type.
Follow safety precautions while using the product.

Maintenance:

Regularly check for any signs of wear or damage.
Clean the product as per the manufacturer’s recommendations.
Keep the product away from extreme temperatures and moisture.

Electronic Regulatory Compliance

SRAM LLC certifies that this product and its packaging are in compliance with:
RE Directive, the Radio Equipment Directive 2014/53/EC
WEEE Directive, the Waste Electrical and Electronic Equipment Directive 2012/19/EU
RoHS Directive, the restriction of the use of certain hazardous substances in electrical and electronic equipment 2002/95/EC
REACh Directive, the Regulation on Registration, Evaluation, Authorization and Restriction of Chemical Directive 1907/2006/EC
Batteries and Accumulators and Waste Batteries and Accumulators Directive 2006/66/EC

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

this device may not cause harmful interference, and
this device must accept any interference received, including interference that may cause undesired operation.

For Model 12300: Operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems.

Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

This device complies with Industry Canada’s license-exempt RSS standard(s).

Operation is subject to the following two conditions:

this device may not cause interference, and
this device must accept any interference, including interference that may cause undesired operation of the device.

The term “IC”: before the radio certification number only signifies that Industry Canada’s technical specifications were met.

RF Radiation Exposure Statement:
Models 00010, 00110, 00210, 12810, 12910, 13200, 00220, 12920, 00030, 00130, 00020, 00120, 13000, 13100, 13110, 00500, 00601, 00610, 65501, 00230, 09601, 12930, 13400, 00021, 00121, 55502, 00022, 00122, 12911, 12300 and 55503 have been tested and complies with FCC PART 1 SUBPART I & PART 2 SUBPART J as well as IC RSS 102 RF radiation exposure limits set forth for an uncontrolled environment when used with SRAM accessories supplied or designated for this product. To satisfy FCC and IC exposure requirements, a separation distance of at least 1.5 cm (3.5cm for 12300) must be maintained between the antenna of this device and persons during device operation. The use of any other accessories may not ensure compliance with FCC PART 1 SUBPART I, PART 2 SUBPART J or IC RSS 102 RF exposure guidelines.
This device meets the FCC requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. The exposure standard employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6 W/kg. Tests for SAR are conducted using standard operating positions accepted by the FCC with the EUT transmitting at the specified power level in different channels. The FCC has granted Equipment Authorization for this device with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this device is on file with the FCC and can be found under the Display Grant section of www.fcc.gov after searching the FCC ID.

Warning : Any changes or modifications not expressively approved by SRAM could void the user’s authority to operate this equipment.

This product is ANT+ certified and complies with the bicycle power ANT+ Device Profile. For a complete listing of ANT+ Certified Products and their specific interoperability, please visit www.thisisant.com.

Electronic Regulatory Compliance Manual

PMN

| ****

Model #

| ****

FCC ID

| ****

IC

| ****

TRA Dealer No: DA51171/16

| ISRAEL

מספר אישור אלחוטי של משרד התקשורת אסור להחליף את האנטנה המקורית של המכשיר ולא לעשות בו כל שינוי טכני אחר

---|---|---|---|---|---
Left Shifter| 00010| C9O-LSBB1| 10161A-LSBB1| ER64861/18| 51-75254
Right Shifter| 00110| C9O-RSBB1| 10161A-RSBB1| ER64862/18| 51-75255
BlipBox| 00210| C9O-BOXB1| 10161A-BOXB1| ER64863/18| 51-75256
Front Derailleur| 12810| C9O-FDB1| 10161A-FDB1| ER64864/18| 51-75257
Rear Derailleur| 12910| C9O-RDB1| 10161A-RDB1| ER64865/18| 51-75258
Seatpost| 13200| C9O-SPMB1| 10161A-SPMB1| ER69128/19| 51-67177
Electronic Controller| 00220| C9O-SLMB1| 10161A-SLMB1| ER67897/18| 51-67174
Rear Derailleur| 12920| C9O-RDMB1| 10161A-RDMB1| ER67785/18| 51-67175
Left Extension| 00030| C9O-LSBB1| 10161A-LSBB1| ER95831/21| 51-79732
Right Extension| 00130| C9O-RSBB1| 10161A-RSBB1| ER95833/21| 51-79731
Left Shifter| 00020| C9O-LSBB2| 10161A-LSBB2| ER92521/20| 51-76414
Right Shifter| 00120| C9O-RSBB2| 10161A-RSBB2| ER92522/20| 51-76415
Front Suspension| 13000| C9O-FSMB2| 10161A-FSMB2| ER93178/21| 51-76736
Rear Shock| 13100| C9O-RSMB1| 10161A-RSMB1| ER93180/21| 51-76735
Pedal Sensor| 00500| C9O-PDMB2| 10161A-PDMB2| ER93176/21| 51-76734
Pressure Sensor| 00601,

00610

ASIAN HEADQUARTERS HIDF16000136 HIDF16000136 SRAM Taiwan No. 1598-8 Chung Shan Road Shen Kang Hsiang, Taichung CityTaiwan R.O.C.
WORLD HEADQUARTERS SRAM LLC 1000 W. Fulton Market, 4th Floor Chicago, Illinois 60607 USA
EUROPEAN HEADQUARTERS SRAM Europe Paasbosweg 14-16 3862ZS Nijkerk The Netherlands

FAQ

Q: What do the model numbers signify?
A: The model numbers correspond to different components of the product, enabling easy identification and replacement if needed.

Q: Is this product compatible with other ANT+ devices?
A: Yes, this product is ANT+ certified and complies with the bicycle power ANT+ Device Profile, ensuring interoperability with other ANT+ Certified Products.

Q: How can I troubleshoot interference issues?
A: Ensure proper positioning of the device and check for nearby sources of interference. Refer to the user manual for troubleshooting tips specific to interference.