DO ALL OUTDOORS CT101 Competitor Trap Instruction Manual

June 1, 2024
DO ALL OUTDOORS

DO-ALL-OUTDOORS-logo

DO ALL OUTDOORS CT101 Competitor Trap

Specifications

  • Model: CT101
  • Included Parts:
    • Throwing Arm and Trap head
    • Main Spring and Spade Bolt
    • Tire Mounting Bolt
    • Hardware Rear Leg Section
    • Frame Angle Mount
    • Front Leg Section

Product Usage Instructions

Step 1: Assembly

Follow these steps to assemble the target thrower:

  1. Attach the rear and front leg sections using the provided bolts, washers, lock washers, and nuts.
  2. If mounting on a tire, ensure the front leg is reversed and horizontal.
  3. If mounting on a solid foundation, use suitable material for cushioning effect.

Step 2: Mounting

Mount the Frame Angle Mount and Trap Head using the carriage bolt, washers, lock washers, and wing nut. Ensure all connections are tight.

Step 3: Trigger Setup

Thread trigger string through the eyebolt and tie it to the trigger securely.

Step 4: Spring Installation

Connect the main spring to the swivel spring hook under the Throwing Arm. Secure the spring bolt through the trap head using the washer and wing nut.

Operation

Positioning:

  1. Place the thrower in the desired location.
  2. Firmly implant the frame spikes into the ground for stability.
  3. The base should be flush with the ground surface.

Flight Angle & Elevation Adjustment:

  1. Adjust clay target elevation by moving the wing nut to another adjustment hole.
  2. Do not adjust elevation angle while the thrower is cocked.
  3. Retighten the elevation wing nut after adjustment.

FAQ

Danger:

Troubleshooting:

  1. If clay pigeons only throw a short distance, ensure the trap is firmly secured and tighten the spring nut for increased arm swing speed.
  2. If clay pigeons break during use, adjust the clay pigeon clamp position on the arm to prevent breakage.

Warranty & Customer Service:

Register your product online at www.doalloutdoors.com. Receipt is required for warranty claims.

INCLUDED PARTS

DO-ALL-OUTDOORS-CT101-Competitor-Trap-fig
\(1\)

Installation Instruction

DO-ALL-OUTDOORS-CT101-Competitor-Trap-fig
\(2\)

Place 5/16 x 3/4″ hex bolt upward through front hole in the rear leg section and place the matching left-hand hole in the front leg section over bolt.
*NOTE: If the target thrower is to be mounted on a tire, the front leg should be reversed and horizontal. Then place the corner hole of the support leg over bolt and apply 5/16″ flat washer, 5/16″ lock washer and 5/16″ hex nut. Place two 5/16 x 3/4″ bolts upward through the remaining two holes and apply 5/16″ flat washers, lock 5/16″ lock washers and 5/16″ hex nuts. Tighten with a wrench If the Trap is to be mounted on a tyre (not included), place M8x150 Hex Bolt down through lug hole in wheel, apply flat washer and M8 nut, then tighten. If the Trap is to be mounted on a solid foundation such as a shooting bench, it is advisable to put rubber or other suitable material between the Trap and the foundation in order to provide a cushioning effectDO-ALL-OUTDOORS-CT101-Competitor-Trap-fig \(3\)

Place 5/16 x 3/4” carriage bolt through square hole of Frame Angle Mount and square hole of Trap Head, then apply 5/16” flat washer, 5/16” lock washer and hand tighten wing nut. 2. Place 5/16 x 3/4” hex bolt through the round Angle Mount hole and round Trap Head hole, apply 516” lock washer, 5/16” lock washer and tighten 5/16” nut with wrench.DO-ALL-OUTDOORS-CT101-Competitor-Trap-fig
\(4\)

Thread trigger string through eyebolt and tie one end to trigger.DO-ALL-
OUTDOORS-CT101-Competitor-Trap-fig \(5\)

With the Throwing Arm pointed outward in the 12 o’clock position, connect main spring to the silver swivel spring hook under the arm. Pull long threaded spring bolt through the hole in the back of the trap head next to the trigger release. Connect by using the washer & wing nut.

DO-ALL-OUTDOORS-CT101-Competitor-Trap-fig \(6\)

THANK YOU

Ensure all hardware is tightened. Once the Main Spring is installed, the thrower is live. Please refer to operation and warnings

OPERATION

POSITIONING

  1. Position the thrower in desired location.
  2. Step firmly on each of the 3 corner frame spikes to firmly implant. For maximum stability, drive large nails or stakes (not provided) into the ground using the hole in each leg section.
  3. The top of the base should be imbedded flush with the ground.

FLIGHT ANGLE & ELEVATION ADJUSTMENT

  1. The elevation of the clay targets are adjustable by removing the wing nut and moving it to another adjustment hole. Never adjust the elevation angle while the thrower is cocked.
  2. The elevation wing nut must be retightened following the adjustment. Flight direction is determined by the location of the clay on the throwing arm.

DANGER

  • KEEP SPRING DISCONNECTED WHEN NOT IN USE OR ON DISPLAY
  • THROWING ARM CAN CAUSE SERIOUS INJURY
  • NEVER STAND TO RIGHT OF THE THROWER OR IN THE PATH OF THE THROWING ARM
  • NEVER STORE OR TRANSPORT WITHOUT FIRST REMOVING TENSION SPRING

TROUBLESHOOTING

  1. Clay pigeons only throwing a short distance – Make sure the Trap is firmly secured and won’t move or bounce. Tighten the nut on the spring which will increase arm swing speed.
  2. Clay pigeons breaking during use – Clay pigeon clamp is too close to the trigger. Un-cock the machine and loosen the wing nut and slide the clamp forward on the arm. Re-tighten wing nut.

Warranty & Customer Service

Register your product online at

warranty registration.

Find tech tips, instructions, troubleshooting videos, and more online!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals