DO ALL OUTDOORS FW180x Auto Clay Pigeon Thrower Instruction Manual
- May 15, 2024
- DO ALL OUTDOORS
Table of Contents
- FW180x Auto Clay Pigeon Thrower
- Product Specifications:
- Product Usage Instructions:
- Step 1: Cart Handle Assembly
- Step 2: Attaching Wobbler Base
- Step 3: Attaching Wheels
- Step 4: Connecting Wobbler to Wobbler Base
- Step 5: Securing Trap Base to Wobbler
- Step 6: Attaching Trap Head
- Step 7: Safety Ring Installation
- Q: Are tools included for assembly?
- Q: How many stacker poles are included in the Clay Stack Turret
FW180x Auto Clay Pigeon Thrower
Product Specifications:
- Model: FLYWAY 180X
- Includes various parts for assembly
- Tools not included
- Comes with a corded foot pedal and wireless remote
Product Usage Instructions:
Step 1: Cart Handle Assembly
Prior to assembly, ensure all packaging materials are removed.
Use a 14mm socket for bolts and a 13mm for nuts to assemble the
cart handle.
Step 2: Attaching Wobbler Base
Attach the Wobbler base to the axle and cart handle using the
provided bolts and nuts.
Step 3: Attaching Wheels
Slide washers and wheels onto each side of the axle and secure
with C clips.
Step 4: Connecting Wobbler to Wobbler Base
Secure the Wobbler to the Wobbler base using the provided bolts,
washers, and nuts.
Step 5: Securing Trap Base to Wobbler
Secure the Trap Base to the top of the Wobbler using the
provided bolts, washers, and nuts.
Step 6: Attaching Trap Head
Secure the Trap Head to the Trap Base using the provided bolts
and plastic washers.
Step 7: Safety Ring Installation
Hook the Safety Ring onto the Safety Ring Arms and secure it to
the rear of the Trap Head. Thread in each of the Stacker Poles to
the top of the Trap Head.
Frequently Asked Questions (FAQ):
Q: Are tools included for assembly?
A: No, tools are not included. You will need a 14mm socket for
bolts and a 13mm socket for nuts.
Q: How many stacker poles are included in the Clay Stack Turret
Assembly?
A: The Clay Stack Turret Assembly includes 12 male/female
stacker poles and 12 female/female stacker poles.
FLYWAY
180X
INCLUDED PARTS
Cart Handle Assembly With (2) Long & (1) Medium 14mm Hex Bolts
with (6) Washers and (3) Nuts
Clay Stack Turret Assembly with (12) male/female stacker poles, (12)
female/female stacker poles, and (24) bolts (these come fastened to the
poles).
Main Spring and Spadebolt
(4) Short 14mm Hex Bolts, (8) washers and (4) nuts to connect Wobbler to
Wobbler Base
Wobbler Base with (2) Long 14mm Hex Bolts and (2) Short 14mm Hex Bolts with
(8) Washers and (4) Nuts to
connect Wobbler Base to Cart and Axle Assembly
(4) 17mm Hex Bolts & (4) Plastic Washers to connect Trap Head to Trap Head Base
Wobbler
Trap Head Base with (4) Short 14mm Hex Bolts with (8) Washers and (4) Nuts to
connect Base
to the top of Wobbler
Axle and (2) Wheels with (4) Washers and (2) “C” Clips
Safety Ring
Corded Foot Pedal
Wireless Remote
TOOLS NOT INCLUDED
Ground Stake
1
NOTES
2
Medium
3
2
1
Long
STEP 1
1 2 3
Prior to assembly, please be sure that all zip ties, cardboard, styrofoam, and
bubble wrap are removed from the unit.
Using a 14MM socket for the bolts and a 13MM for the nuts, assemble the cart
handle using the 2 long and 1 medium length bolts. (In order: Bolt, Washer,
Cart
Assembly, Washer, secure with Nut) 3
3
Bottom View
Long
5
Long
4
Short
STEP 2
4
3 (from Step 1)
5
Using a 14MM socket for the bolts and 13MM for the nuts, attach the Wobbler
base to the Axle and Cart Handle using the 2 long and 2 short length 14mm
bolts. (In order: Bolt, washer, Wobbler Base, axle/cart handle, washer, and
secure with nut.)
4
6
4
6
STEP 3
4
6
Slide a Washer, then a Wheel, then another Washer onto one side of the axle,
Secure with a “C” clip. Repeat this for the second side.
5
7 5
STEP 5
4
7
5
Using a 14MM Socket for the Bolts and a 13MM for the Nuts, secure the Wobbler
to the Wobbler base using the (4) provided bolts, 1 Bolt, 2 Washers, 1
Nut on each corner. (In order: Bolt, Washer, Wobbler, Wobbler Base, Washer,
secure with Nut)
6
Front side
Rear side
STEP 6
This side towards rear of trap
7
8
Using a 14MM Socket for the Bolts and a 13MM for the Nuts, secure the Trap
Base to the top of the Wobbler using the (4) provided bolts, 1 Bolt, 2
Washers,
1 Nut on each corner. (In order: Bolt, Washer, Trap Base, top of Wobbler,
Washer, secure with Nut
underneath)
7
Trap Head
Rear
Front
Trap Base
STEP 7
Bolts and Plastic Washers
9
(Circled in white, stacker poles
and safety ring not yet installed)
8
Using a 17MM Socket for the Bolts and a 13MM for the Nuts, secure the Trap
Head (9) to the Trap Base (8) using the (4) provided bolts and (4) plastic
Washers.
(In order: Bolt, Trap Base, Plastic Washer, then into the threads on the Trap
Head)
Note: This step may take 2 people as the Trap Head is fairly heavy. 8
Figure 1
Figure 2
STEP 8
10
11
Hook the Safety Ring onto the Safety Ring Arms (top of Figure 1), then secure to the rear of the Trap Head by loosening the two bolts (bottom of Figure 1) slightly, then push the ends of the ring under the clamps and resecure the 2 bolts.
Thread in each of the Stacker Poles to the top of the Trap Head (Figure 1),
then, using the (24) supplied bolts, secure the Top piece of the Turret
Assembly to the top of the Stacker Poles. (Figure 2)
9
Underneath Trap Head
Rear of Trap Head
Figure 1
Figure 2
STEP 9
12
Hook the Main Spring under the Trap Head Pivot. (Figure 1) Push the Spade Bolt
through the hole in the rear of the Trap, then secure with
the provided tension knob until you feel tension on the spring. (Figure 2)
10
THANK YOU
ONCE THE MAIN SPRING IS INSTALLED, THE TRAP IS NOW LIVE AND CAN GO OFF IF LEFT
IN THE COCKED
POSITION. PLEASE USE EXTREME CAUTION AND ALWAYS REMOVE SPRING WHEN
TRANSPORTING,
ADJUSTING, OR STORING THE TRAP.
Warranty & Customer Service
Register your product online at www.doalloutdoors.com. Receipt is required for
warranty registration. ONE YEAR PARTS WARRANTY.
DO-ALL OUTDOORS LLC 1(866)SHOT-DOC Monday – Friday
8:00 AM to 4:00 PM customerservice@doalloutdoors.com
Nashville, Tennessee, USA
Find tech tips, instructions, troubleshooting videos, and more online at
doalloutdoors.com
11
Operation
1. Make sure deep cycle battery (not included) is fully charged. Before
clamping wobbler and trap alligator clips to battery, make sure the toggle
switch on the trap is set to off. NEVER CARRY TRAP BY THROWING ARM – THIS
CAN BEND AND AFFECT PERFORMANCE! 2. Connect foot pedal to the corded 3 prong
plug coming out of the trap. NEVER PLUG THIS INTO A WALL. 3. Connect red
alligator clips to the positive battery post and the black alligator clips to
the negative battery post. 4. Flip the toggle switch on the trap up to
“disarm.” Once arm moves to 12 o’clock position, turn the machine back off and
load STANDARD SIZE CLAYS ONLY into the stacker tube assembly. Once the trap is
loaded, you can flip the toggle switch down to “on.” The arm will rotate
counterclockwise and automatically load a clay onto the throwing arm. THE TRAP
IS NOW COCKED. PLEASE USE EXTREME CAUTION. 5. To turn the wobbler on, flip the
switch to on. The wobbler will begin moving the trap head side to side until
it is manually turned off. 6. ALWAYS set trap up pointing away from
bystanders, trees, and animals with a recommended 400 meter open field/shot
fall zone. Always look over the trap for damage and test throw a few clay
pigeons before use to make sure the trap is operating properly. NEVER ADJUST
TRAP WHEN COCKED AND IN FIRING POSITION!!! 7. With the shooter/bystanders
standing to the left or behind the trap, press the foot pedal to throw the
clay!
8. When you are done shooting, switch the toggle switch to disarm, hold the
foot pedal down until the throwing arm reaches 12 o’clock, and turn the toggle
switch to off. The trap is now safe to unload/move.
12
NOTES
13
Troubleshooting
ALWAYS REMOVE MAIN SPRING PRIOR TO TROUBLESHOOTING
MACHINE NOT TURNING ON
1. CHECK BATTERY CONNECTION. THE MACHINE DRAWS 16 AMPS TO WORK PROPERLY. WE
RECOMMEND A DEEP CYCLE BATTERY WITH A MINIMUM OF 675 COLD CRANKING AMPS.
2. CHECK THE 15A AUTOMOTIVE BLADE FUSE IN THE REAR OF THE TRAP HEAD. REMOVE
THE COVER AND PULL THE FUSE OUT TO INSPECT. REPLACE AS NEEDED.
3. CHECK RELAY. PLEASE EMAIL OR CALL CUSTOMER SERVICE IF ISSUES CONTINUE.
AUTO FIRING/NOT FIRING
1. IF THE TRAP CONTINUES TO FIRE, UNPLUG THE FOOT PEDAL. IF IT STOPS, THE
SCREWS ON THE FOOT PEDAL NEED TO BE LOOSENED TO DEPRESS THE PEDAL DURING
OPERATION.
2. IF FOOT PEDAL ISSUES CONTINUE, PLEASE SEE OUR TROUBLESHOOTING PAGE ON OUR
WEBSITE FOR TESTING YOUR FOOT PEDAL.
3. ONCE YOU HAVE ESTABLISHED YOUR FOOT PEDAL IS NOT THE ISSUE, MOVE ON TO THE
LIMIT SWITCH. IF YOUR TRAP CONTINUES TO AUTO FIRE, USE A 2.5MM ALLEN WRENCH TO
LOOSEN
THE ALLEN SCREW AND ADJUST THE LIMIT SWITCH UP SO THE ARM WILL TRIGGER THE
LIMIT SWITCH EARLIER TO STOP THE ARM
FROM CONTINUOUS FIRING
4. IF THE TRAP WILL NOT FIRE AND COINCIDES WITH THE LIMIT SWITCH, THIS MEANS
THE ARM IS STOPPING TOO SOON. THE LIMIT SWITCH NEEDS TO BE ADJUSTED DOWN AND
THEN
RECHECKED TO ENSURE PROPER FIRING
5. A GOOD RULE OF THUMB FOR ARM PLACEMENT WHEN LOADED IS TO MAKE SURE THE
CLAY LOADS BETWEEN 1/2 AND 1 INCH FROM THE RUBBER STRIP. IF IT’S FARTHER, THE
ARM IS STOPPING TOO SOON.
BREAKING CLAY PIGEONS
1. MAKE SURE THE TURRET ASSEMBLY IS INSTALLED CORRECTLY AND ALL BOLTS AND
POLES ARE SECURELY TIGHTENED.
2. IF TRAP IS “JUMPING” AROUND WHEN THE ARM SWINGS, THIS COULD BREAK CLAYS IN
THE STACK OR WHILE LOADING ONTO ARM. THE TRAP SHOULD BE SECURED USING STAKES
(NOT
INCLUDED) OR BY MOUNTING TO A BOARD OR PIECE OF PLYWOOD FOR STABILITY.
3. SOMETIMES WHEN THE STACK IS DOWN TO A FEW CLAYS, THE MOTION OF THE TRAP
CAN THROW THE CLAY PIGEONS AROUND AND THEY BREAK. ONCE YOU GET DOWN TO 2-3
CLAYS LEFT, ADD MORE TO WEIGH DOWN THE STACK AND CONTINUE SHOOTING!
4. CHECK TO SEE WHERE THE BASE OF FEEDER BRUSHES ARE TO THE TOP OF THE CLAY
ARM. THE MOUNTING HARDWARE SHOULD NEVER TOUCH THE TOP OF THE BIRD. IF THIS IS
HAPPENING, THE ARM OR CHASSIS IS BENT
14
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>