DO ALL OUTDOORS Flyway One HD Clay Pigeon Thrower Instruction Manual

DO ALL OUTDOORS Flyway One HD Clay Pigeon Thrower

Product Specifications

• Product Name: FLYWAY ONE
• Included Parts:
  • Trap Head
  • Main Spring and Spade Bolt
  • Angle Mount
  • Foot Pedal
  • Leg Cross Arm
  • Parallel Leg Frame Base Safety Ring Arms
  • Frame Angle Mount
  • Safety Ring
  • Bolts, Washers, one Nut and one Hand Knob for Angle Mounts
  • 3 Bolts, 6 Washers and 3 Nuts for Frame Assembly
  • Long Bolt, Washers and Nut
  • Allen Bolts for Safety Ring Arms
  • Safety Ring Studs
  • Large Bolt and Nut
  • Ground Stake
• Tools Not Included: 1

Product Usage Instructions

1. Step 1: Assembling the Frame
   Begin by placing the Frame Angle Mount below the Leg Cross Arm. Slide a washer on each bolt, then secure all parts with washers and nuts.

2. Step 2: Attaching Angle Mount
   Attach the Angle Mount to the Base Angle Mount using the provided bolts, washers, nut, and hand knob for easy height adjustment.

3. Step 3: Attaching
   Foot Pedal Attach the Foot Pedal to the Parallel Leg Frame Base using the Long Bolt, Washers, and Nut. Secure the bolt through the front hole in the frame and through the foot pedal.

4. Step 4: Attaching Trap Head
   Attach the Trap Head to the Angle Mount using the Large Bolt and Nut.

5. Step 5: Mounting Safety Ring Arms
   Mount the Safety Ring Arms onto the Trap Head using the provided Allen Bolts.

INCLUDED PARTS

TOOLS NOT INCLUDED

1. STEP 1
   Begin by placing the Frame Angle Mount below the Leg Cross Arm, and the open end of the Parallel Leg Frame Base below the Frame Angle Mount. Then, place one washer on each bolt, then slide through all 3 parts above, secure on the bottom with another washer, followed by a nut.

2. STEP 2
   Attach the Angle Mount to the Base Angle Mount using the 2 short bolts, with washers, one nut and one hand knob. The Hand Knob goes in the back for easy height adjustment.

3. STEP 3
   Attach the Foot Pedal to the Parallel Leg Frame Base by using the Long Bolt, Washers, and Nut. Attach one Washer to the Bolt, then push the Bolt through the front hole in the Frame, through the hole in the Front of the Foot Pedal, then through the other side of the Frame. Secure with the other Washer and the Nut on the outside of the opposite side of the Frame.

4. STEP 4
   Attach the Trap Head to the Angle Mount using the Large Bolt and Nut.

5. STEP 5
   Mount the Safety Ring Arms onto the threaded front tabs located on the Trap Head using the provided Allen Bolts

6. STEP 6
   Mount the Safety Ring Studs to the Parallel Leg Frame Base, threading from the outside in on each side of the Base.

7. STEP 7
   Slide the Safety Ring through the Safety Ring Arms and feed through them to loop around the Trap Head and secure by sliding each end of the Safety Ring onto the Safety Ring Studs.

8. STEP 8
   Hook the end of the Main Spring onto the Eyelet on the Trap Head indicated above.
   Then, remove the plastic grommet, washer and nut from the Spade Bolt. Slide the Spade Bolt through the hole in the Foot pedal as indicated above. Then, resecure the Grommet, Washer, and tighten nut until 3-4 threads are exposed. This can be adjusted later but is a starting point for spring tension.

9. STEP 9
   Set the Clip on the end of the Foot Pedal’s Chain to desired length. Then attach clip to the top of the Trigger on the Trap Head.

THANK YOU
ONCE THE MAIN SPRING IS INSTALLED, THE TRAP IS NOW LIVE AND CAN GO OFF IF LEFT IN THE COCKED POSITION. PLEASE USE EXTREME CAUTION AND ALWAYS REMOVE SPRING WHEN TRANSPORTING, ADJUSTING, OR STORING THE TRAP.

OPERATION

1. Position trap in desired location suitable for shooting trap.
   ALWAYS MAKE SURE YOU POINT THE TRAP IN A SAFE DIRECTION AWAY FROM BYSTANDERS, TREES, OR ANIMALS WITH AT LEAST A 400 METER OPEN FIELD/SHOT FALL ZONE.

2. Once trap has been inspected to ensure it’s in good working order, place ground stake through the hole in the rear of the trap. This will help hold the trap in place.

3. Elevation can be adjusted by using the plastic hand crank on the Angle Mount & direction can be adjusted by loosening the Large Nut below the Pivot mount.
   When desired elevation and direction is achieved, hand tighten both the nut and hand crank. NEVER ADJUST THE TRAP WHILE IT IS COCKED!

4. With the throwing arm in the 12 o’clock position, place a clay pigeon under the clay pigeon clamp and rotate clockwise until it reaches the 6 o’clock position and locks into the trigger. BE SURE TO TEST THROW PRIOR TO CONTINUOUS USE TO  ENSURE TRAP IS IN GOOD WORKING ORDER.

5. With the shooter positioned to the left of the trap, press the foot pedal to release the arm to throw the clay.

TROUBLESHOOTING

1. Clay pigeons only throwing a short distance  Make sure the Trap is firmly secured and won’t move or bounce. Tighten the nut on the spring which will increase arm swing speed.
2. Clay pigeons breaking during use Clay pigeon clamp is too close to the trigger. Un-cock the machine and loosen the wing nut and slide the clamp forward on the arm. Retighten wing nut.

Warranty & Customer Service Register your product online at www.doalloutdoors.com  Receipt is required for warranty registration.
ONE YEAR PARTS WARRANTY.

customerservice@doalloutdoors.com 1(866)SHOT-DOC
Monday – Friday 8:00 AM to 4:00 PM
DO-ALL OUTDOORS LLC – Nashville, Tennessee, USA Find tech tips, instructions, troubleshooting videos, and more online!

1 -B66-SH□T -DOC
( 1-866-7£16-8362)
DDALLDUTD□DRS.CM CUSTOMERSERVICE1@DOALLOUTDOORS.COM

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>