Sunco SH_GL2-WH-FS 2ft LED Grow Light User Manual
- June 1, 2024
- SUNCO
Table of Contents
SH_GL2-WH-FS 2ft LED Grow Light
Lighting made better.
User Manual
2ft. LED Grow Light
SKU: SH_GL2-WH-FS
support@sunco.com 844-334-9938
AMERICAN COMPANY
Whats in the Box?
Grow Light
Le(tlittheerraellbye) light!
Safety Information
To reduce the risk of fire, electric shock, or physical injury:
· Turn off power before changing fixture. · Suitable for use in damp
environments at
temperatures ranging from 4°F to 113°F. Not for use where directly exposed to
water. · Not intended for use with emergency fixtures. · Not compatible with
photo controls. · Not compatible with occupancy sensors. · Not compatible with
dimmers.
· Not compatible with timing devices. · All electrical connections must be in
accordance with
local and National Electric Code (N.E.C.) standards. · Please review
installation manual carefully before
proceeding. Consult a qualified electrician if you are unfamiliar with proper
electrical wiring connections.
WARNING: Cancer & Reproductive Harm- www.P65Warnings.ca.gov
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1.) This device may not cause harmful interference.
2.) This device must accept any interference that may cause undesired operation. Please review all instructions carefully prior to installation.
1
Installation Guide
ON OFF
STEP 1 a. Turn off circuit breaker before installation. b. Surface must
support fixture weight. Plaster board: Requires 3/8″ thickness. Use #8 eye
hook screws with anchors or expansion bolts (not included).
STEP 2 a. Drill pilot holes.
b. Insert two plastic anchors, then screw each eye hook into an anchor.
Connect to Power Outlet
Connect to additional lights
STEP 3 a. Depending on your lighting plan, space any additional anchors
accordingly. b. Link up to 4 shop lights together
2
Installation Guide (Cont.)
STEP 4 a. Install a “V” hook into one end of the chain link provided. Loop one
S Hook onto the other end of the chain. Repeat with second chain.
b. Use pliers to crimp ends and secure as needed.
STEP 5 a. Insert the “V” hook ends into the slots in the light fixture end cap. Repeat steps on the opposite side.
b. Hang the loose ends of the chain onto the Screw Eye
Side
hooks in the ceiling.
12″- 39″
STEP 6 a. Plug the power cord into an electrical outlet. Turn on the circuit
breaker and test the light.
b. Distance between lamp and plant surface should be between 12 – 39 inches.
3
Installation Guide
ON OFF
21″
STEP 1 a. Turn off circuit breaker before installation. b. Surface must
support fixture weight. Plaster board: Requires 3/8″ thickness. Use #8 eye
hook screws with anchors or expansion bolts (not included).
STEP 2 a. Install four plastic anchors 21″ inches apart. Insert a screw into
each anchor. b. Gap between cap nut and ceiling should be 0.33 inches.
0.33″ 0.14″
Connect to Power Outlet
Connect to additional lights
STEP 3 a. Depending on your lighting plan, space any additional anchors
accordingly. b. Link up to 4 shop lights together
4
Installation Guide (Cont.)
STEP 4 a. Lift fixture up to screws and slide to one side to secure into
place. Fixture should be firmly fixed against screws.
STEP 5 a. Distance between lamp and plant surface should be between 12 – 39 inches.
12″- 39″
ON OFF
STEP 6 a. Plug the power cord into an electrical outlet. b. Turn on the
circuit breaker and test the light.
5
Product Details
Dimensions
3.2″ Width
24″ Length
1.3″ Height
Specifications
Voltage Wattage Power Factor Beam Angle PPF PAR Dimmable
120V 20W >0.7 120° 30.53umol/s 6893.517mW No
5 ft. Length
Average Lifetime Lumens Moisture Rating CRI Usage Frequency Warranty
50000 hrs 1400LM Damp >80 Indoor 60Hz 3 Years
6
Light Distribution Angle
Not No
awloirgrhietisn, ygonuercda?n
skip
this
page
AVERAGE BEAM ANGLE (50%): 117.6 DEG C0/180 117.6° C90/270 117.6°
UNIT:cd Luminous Intensity Distribution 1
Lighting distribution angle refers to the spread of light emitted from a light source. It is an important factor to consider when selecting a fixture or bulb, as it affects the way it will illuminate an area. There are two main types of lighting distribution angles: A symmetric lighting distribution emits light evenly in all directions, creating a coneshaped pattern that provides a pool of light. This type of lighting is ideal for general lighting and illuminating large areas. Common applications for symmetric lighting include general area illumination, security lighting, and perimeter lighting. Symmetric lighting is also used to a
certain degree in up-lighting. An asymmetric lighting distribution angle, also known as beam angle, creates a pattern that focuses light in a specific direction. This type of lighting is ideal for task lighting as it reduces glare and light spill in other areas. Common applications include task lighting in spaces such as landscape settings, retail stores, museums, and much more. It is important to note that the lighting distribution angle can also be affected by other factors such as the reflector design of the light source, the type of lens used, and the distance between the light source and the surface being illuminated.
7
Customer Support
Warranty Policy
This product is covered by our industry leading 3 year warranty.
It gets even better – scan the QR code for 2 extra years of protection!
Secxatnramyeeafrosr! two
30 Day Return Policy
At Sunco, we value our customers and stand by the quality and performance of our products.
If you are not completely satisfied with your purchase, we accept returns within 30 days of your purchase date.
Customer Service
Our Los Angeles team of lighting experts is here to assist you with all your
needs! Contact us at:
Email: support@sunco.com
Call or Text: 844-334-9938
8
Lighting made better.
support@sunco.com 844-334-9938
REV1.0
AMERICAN COMPANY
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>