PROMETHEUS BTC-PSMHD Strike Force Wireless User Guide
- June 1, 2024
- PROMETHEUS
Table of Contents
PROMETHEUS BTC-PSMHD Strike Force Wireless
Initial Setup
Open the front door of your trail camera, and press the battery eject button.
Install 8 AA alkaline batteries, and re-insert the battery tray.
Next, Install your SD card into the SD card slot on the bottom of the camera.
Use only good quality SanDisk or Browning SD cards.
CELLULAR SETUP
Download the Strike Force Wireless app from the App Store or Google Play on
your mobile device. Set up an account on the new App. From the App, select
“Setup New Camera”. This will bring up a QR code reader.
Power on the trail camera and press the Mode button. Highlight either ATT or
Verizon as your preferred carrier. Confirm your selection. Scan the QR Code
that appears on the camera’s screen with the QR code reader on your mobile
app. This will register the camera information on your Strike Force Wireless
account. Follow the App instructions for picking your camera’s data. After 5
minutes, your camera will be set up on the cellular network.
You can do a manual test by navigating to the LTE TEST camera menu. This will
make test communication to your account at Strike Force Wireless.
CAMERA SETTINGS
After powering on the trail camera, press the mode button to access the
avaliable setting options. The setting options are as follows:
Set Date
Set Time
Camera Mode : Trail / Video
Capture Delay :1, 5, 10, 30 seconds, 1, 2, 5, 10, 30, 60 minutes
Picture Size : 2, 4, 8 or 20MP
MultiShot: 1-8 shots per trigger
Temperature Units : Fahrenheit or Celcius
Picture Info Strop : on / off
SD Card Management : on / off
Motion Test : Activate to test the PIR range and check setup in the
field.
Camera Name : Add a custom name for your camera in tis field.
Set Default : Resets your camera to factory defaults.
Delete All: This erases and reformats your SD card. Software Update: You
can update your camera software here.
LTE Test: You can run a manual cellular test here by pressing the OK
button.
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digi tal device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement: This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled environment. In order to avoid
the possibility of exceeding the FCC radio frequency exposure limits, Human
proximity to the antenna shall not be less than 20cm (8 inches) during normal
operation.
Shielded cables with ferrite must be used with this unit to ensure compliance
with the Class B FCC limits.
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void th e u ser’ s authority to operate the equipment.
This user manual covers Defender Pro Scout Max High Definition Cameras
Model Number: BTC-PSMHD
FCC ID: 2ALGTBTC-PSMHD
Customer Support
Browning Trail Cameras
Customer Service: 888-618-4496
M-F 9am – 5pm CST
www.browningtrailcameras.com