Insta360 CINSAAVG GPS Preview Remote User Guide
- June 1, 2024
- Insta360
Table of Contents
Insta360 CINSAAVG GPS Preview Remote
Product Specifications
- Brand: GPS Preview Remote
- Model: XYZ123
- Color: Black
- Material: Plastic
- Compatibility: Compatible with cameras supporting remote control
- Power Source: Rechargeable battery
Product Usage Instructions
1. Overview
The GPS Preview Remote includes the following components:
- A. Shutter Button
- B. Power Button
- C. Led Screen
- D. Speaker
- E. Heart rate sensor
- F. Magnetic charging points
2. Charging
To charge the remote:
- Connect the charging port with the magnetic charging points on the remote.
- Ensure proper alignment for effective charging.
3. Assembly
To assemble the remote:
- Install the remote onto the hand strap and wear it on your hand.
- For selfie stick usage, attach the remote to the hand strap and then connect it to the selfie stick securely.
- For bike or motorbike installation, follow the provided instructions.
Frequently Asked Questions
- Q: How do I connect the remote to the camera?
- A: To connect the remote to a camera, tap the connected device card in the remote control application center to enter pairing mode.
- Q: How do I power on/off the remote?
- A: When powered off, long press the power button to turn on. To power off, long-press the power button for 3 seconds.
Overview
- A.Shutter Button
- B. Power Button
- C.Led Screen
- D.Speaker E.Heart rate sensor F.Magnetic charging points
Charging
The charging port has a magnetic suction function. Pay attention to the magnetic direction and align the charging port with the Magnetic charging points
Assembly
-
Install the Remote onto the hand strap, then wear it on your hand.
-
Install the Remote to a selfie stick
Install the Remote onto the hand strap. Position the strap to the selfie stick, stretch the strap properly and fasten it on the selfie stick. -
Install the Remote to a bicycle or motorbike.
How to use
Power on/off
- When powered off, long press the power button to power on.
- When powered on and the Remote does not connect with a camera, long press the power button for 3 seconds to power off.
- When powered on and the Remote connects with a camera, long press the power button for 3 seconds to prompt a popup and choose from Power off the remote, Power off the camera or Power off both.
Connection and Wake up
Connecting a camera
Tap the connected device card in the remote control application center to make the remote control enter the pairing mode. Then enter the camera’s “Shortcut Center – Settings – remote control” and start to search and connect the remote control. If the connected successfully, the watch will prompt the connection success page.
Control the camera
After connecting, users can remote the camera by operating the Remote.
Preview page
After connected, the remote will synchronize the camera’s information and the corresponding information will be displayed on the preview page:
- Camera’s capacity information
- GPS signal intensity
- Camera’s battery level
- Camera preview page
- Camera’s shooting mode icon
- Camera’s current shooting specification
- Current speed
- Current direction
- Current heart rate
Switch shooting modes
- Screen operation: Swipe from left to right or reverse on the preview page to switch shooting modes.
- Button operation: Press the power button once to display the shooting mode, press the power button repeatedly to choose a desired mode.
shooting specification
Swipe from bottom to top or reverse on the preview page to enter shooting specification setting page.
3A parameters
Swipe from left to right or reverse on the preview page to enter 3A parameter page.
Shooting
In the preview state, short press the shutter button to control the camera to start recording/shooting; When the camera is in recording, short press the shutter button to control the camera to stop recording.
App center
- Heart rate, dashboard and compass
In the App center tap Heart rate, dashboard or compass to enter the corresponding App.
Remote settings
Tap “Settings” in the App Center to enter Settings. Users can view or operate the following contents: Display and brightness, display direction, Sound and vibration, time, location service, heart rate service, geomagnetic service, language, About Camera, and Restore factory Settings.
Firmware updating
Access Insta360 App- Settings – Remote Upgrade, search for and connect the remote. After connected successfully, the App will pop up an update prompt if there is a new version of the firmware. Please complete upgrading according to the App prompts
Safety at a Glance
- The battery is suggested to be used in temperatures ranging from -4°F to 104°F. Use of the battery in high or low temperature environments can affect battery life and shorten its running time.
- Never disassemble or pierce the product in any way or the battery may leak, catch fire, or explode.
- Do not drop or strike the product. Do not place heavy objects on the product.
- Do not leave the battery near heat sources such as a furnace or heater. Do not leave the batteries inside of a vehicle on hot days.
- Always use an Insta360 approved adapter or the special Fast Charge Hub served by Insta360.
- Do not store the battery fully discharged for long periods of time, otherwise it will over discharge and lead to permanent damage
Specifications
Compliance Information
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residentialinstallation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment
FCC SAR:
- The radiated output power of this device is below the FCC radio frequency exposure limits. Nevertheless, the device should be used in such a manner that the potential for human contact is minimized during normal operation. The exposure standard for wireless devices employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6 W/Kg. Tests for SAR are conducted using standard operating positions accepted by the FCC with the device transmitting at its highest certified power level in all tested frequency bands. Although the SAR is determined at the highest certified power level, the actual SAR level of the device while operating can be well below the maximum value. This is because the device is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output. To avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna should be minimized. This device has been tested and meets the FCC RF exposure.Guidelines when used with an accessory designated for this product or when used with an accessory that Contains no metal and that positions the handset a minimum of 0mm from the limbs.
- The maximum SAR value is 0.325W/kg when the device used 0mm close to user
IC STATEMENT
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions:
- This device may not cause interference; and
- This device must accept any interference, including interference that may cause undesired operation of the device.
IC SAR
For body-worn operation, the device has been tested and meets the standards RSS-102,Issue 5 &IEC/IEEE 62209-1528:2020 of IC RF exposure, The maximum SAR value is 0.325W/kg when the device used 0mm close to user.
Declaration of Conformity
Arashi Vision Inc.hereby, declares that this product is in compliance with the essential requirement and other relevant provisions of the directive 2014/53/EU . A copy of the EU Declaration of Conformity is available online at http://www.insta360.com/cn/euro-compliance
GB Compliance Statement
Arashi Vision Inc.hereby, declares that this product is in compliance with the essential requirement and other relevant provisions of Radio Equipment Regulations 2017. A copy of the GB Declaration of Conformity is available online at http://www.insta360.com/cn/euro-compliance
WEEE Directive
Correctly dispose of this product. This marking indicates that this product should not be disposed with other household wastes throughout the EU/UK. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle responsibly to promote the sustainable reuse of material resources. To safely recycle your device, please use return and collection systems or contact the retailer where the device was originally purchased
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>