Aileap SPK350X 4 Inch Full Range Waterproof Motorcycle Stereo Bluetooth Speakers Instruction Manual

June 1, 2024
Aileap

Aileap SPK350X 4 Inch Full Range Waterproof Motorcycle Stereo Bluetooth

Speakers

Aileap-SPK350X-4-Inch-Full-Range-Waterproof-Motorcycle-Stereo-Bluetooth-
Speakers-product

CONTENTS

  • 1 x Master Speaker
  • 1 x Slave Speaker
  • 2 x Mounting Clamps
  • 1 x Wired Control
  • 1 x AUX Cable
  • 1 x SAE Power Cord
  • 1 x User’s Manual

FEATURES

  • 4″ High-Performance Waterproof Speakers
  • Built-in 300W D-Class Power Amplifier
  • Built-in Bluetooth 5.0 for Audio Streaming
  • Support USB Input
  • 3.5mm AUX Input Jack
  • All-Function Wired Remote
  • SAE Quick Disconnect Power Cable
  • Advanced Plating Process – Fade and Scratches Resistant

READ BEFORE INSTALLATION

  1. The components and wiring should not be installed on or around any moving parts, keep away from ignition parts, fuel lines, engine or any hot exhaust.
  2. peakers should not be installed where they might inhibit safety features on the vehicle such as lights, horns, and brake levers.
  3. always test the speakers/amplifier before installation. Connect to the battery and play the music for at least 3 minutes to ensure the product is fully functional.
  4. Splash, water and dust resistance are not permanent conditions and resistance might decrease due to normal wear.
  5. To avoid battery draining, disconnect the speaker from the battery if the motorcycle/ATV is planned to be non-operation for more than 15 days.
  6. Engine, pipe and wind noise will overpower any speakers once they reach certain speeds, it is physics and unavoidable.
  7. Please connect to the correct power supply (DC 12V), and make sure the power cable is correctly connected to the battery.
  8. Cutting rubber inserts may be required for certain bar sizes.

INSTALLATION

Aileap-SPK350X-4-Inch-Full-Range-Waterproof-Motorcycle-Stereo-Bluetooth-
Speakers-fig- \(1\)

wiring

  1. Connect the RCA male plug * (slave speaker) to the RCA female plug 2 (master speaker).
  2. Connect the 8 (wired control) to 5).
  3. To connect with a mp3 audio source, connect the mp3 player to the 4 AUX input with the AUX cable
  4. To play MP3 files with a USB disk (FAT Format), connect the USB drive to
  5. USB Port.
  6. Plug in the 6 (power cord) to the I SAE power input and then connect to a 12V battery. (Positive: Red, Negative: Black)

Connections

  1. SAE Quick Disconnect Power Input
  2. Master Speaker Female RCA Port
  3. USB Input Port
  4. 3.5mm AUX Input
  5. Wired Remote Input
  6. SAE Power Cord
  7. Slave Speaker with RCA Male Plug
  8. Wired Remote ControlAileap-SPK350X-4-Inch-Full-Range-Waterproof-Motorcycle-Stereo-Bluetooth-Speakers-fig- \(2\)

Mounting the Speakers

  1. Attach the mounting clamp to the speaker’s bottom using (4) M3x8 mm screws.

  2. Fill the rubber inserted and place the M6 nut in the clamp.

  3. Secure the clamp on the handlebar with a M6x25mm screw.
    Note: We offer a variation of the mounting bracket.

  4. Contact us if the included mounting hardware does not fit your setup.Aileap-SPK350X-4-Inch-Full-Range-Waterproof-Motorcycle-Stereo-Bluetooth-Speakers-fig- \(3\)

WIRED CONTROL OPERATIONS

  1. Power On/off – Long Press
  2. Mode Change – Single Click
  3. Volume Down – Single Click
  4. Volume Up – Single Click
  5. Last Song – Single Click
  6. Next Song – Single Click
  7. Play/Pause – Single Click

Bluetooth

  1. Press the “Mode” button to switch the unit to BT mode (The unit will enter into BT mode by default upon turning on).
  2. Enable the Bluetooth function on your smartphone.
  3. Search for a Bluetooth device named “GOHAWK” and pair it.

USB

  1. Insert a USB drive and press the mode button to switch to the USB function.
    NOTE : The USB drive must be in FAT format. USB to Phone as a music playback is not supported.

TROUBLESHOOTING

The unit is not turning on:

  1. Make sure the wired control is plugged into the correct jack. (There are two 3.5mm jacks, one for Remote and one for AUX)
  2. Inspect the inline fuse of the power cord, and replace it if blown.
  3. Check if the battery is in good condition, the unit requires at least 12V 5A to operate.
  4. Wired control is defective if no light indication, contact us for replacement.

The volume is not loud enough

  1. Compare between speakers to identify if one of them is blown.
  2. Adjust the speaker’s direction toward the driver’s position.
  3. Turn on the volume on BOTH stereo units AND music devices (such as smartphones and MP3 players)
  4. Check if your battery has at least 12V after the startup of the engine.

USB is not playing the music

  1. USB input supports FAT format USB drive only.
  2. USB to Phone is not supported.

The mounting clamp does not fit

  1. We offer a variation of the mounting bracket.
  2. Contact us if the included mounting hardware does not fit your setup.

SPECIFICATIONS

Built-in Amplifier

  • Working Voltage: DC 10-16 V
  • Rated Power: 2*20W 40
  • Peak Power: 300W
  • Channel: 2.0
  • Channel Separation: >45dB
  • Frequency Range: 87.5-108Mhz
  • Sensitivity: 50mA
  • Fuse rating: 7.5A

Speaker

  • Outline Size: 4″ x 5″
  • Sound Core: 3″ Full Range
  • Rated Power: 20W
  • Peak Wattage: 100W
  • Impedance: 40
  • Resonc Frequency: 165hz
  • Effective Frequency: Fo-12Khz
  • Sensitivity: 85dB

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals