tp-link HS200-2 Smart Wi-Fi Light Switch User Guide

: June 1, 2024
: tp-link

Table of Contents

Wire Your Switch
Set Up Your Switch
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Quick Start Guide
Smart Wi-Fi Light Switch, Two-Gang

©2023 TP-Link 7106510701 REV6.0.0
*Images may differ from your actual product.

Wire Your Switch

Turn off the circuit breaker for all switches in the wallbox. Check whether your power is off by turning your switches on and off a few times. Make sure your old switches are turned off before continuing wiring. CAUTION!
1. Risk of Electric Shock – The product should be installed by a qualified electrician.
2. High Voltage – Disconnect power supply at the circuit breaker before servicing.
3. Use copper conductors only
Remove the old wallplate. Use a voltage detector to test terminals and other metal parts to confirm that all power is off.
Unscrew one of the two old switches and pull it out. Use a voltage detector to test all wires connected to the old switch and in the wallbox to confirm that all power is off for the wallbox.
Take a picture of the wires. Then label the wires of the pulled-out switch. • Neutral: Usually a bundle of white wires not connected to the old switch. They may be folded up in the very back of your wallbox. If the old switch is smart, then the neutral wire may be connected to the switch.
• Ground: Usually a green or bare copper wire.
• Line/Load: Usually black, connected to the old switch.
Disconnect the wires from the pulled-out switch. Then connect the wires to one of your smart switches as shown below. No need to distinguish between the Line and Load wires.
Follow the same steps to replace the other old switch with your smart switch.
Screw the switches to the mounting holes without fully tightening them. You may need to adjust their positions for the wallplate.
Use the provided mounting template to help line up the two switches with the mounting holes. Then tighten the screws. Set the mounting template aside and attach the wallplate.
You can turn on the circuit breaker and turn on the lights to check your work.

Appearance

Button Explanations

Reset| Press and hold for about 5s until the LED blinks amber and green to reset Wi-Fi while keeping other settings.
Press and hold for about 10s until the LED blinks amber to restore factory default settings.
---|---
Restart| Press to restart your switch.

LED Status

Solid amber	Starting up.
Blinking amber & green	Ready for setup;

Set Up Your Switch

DOWNLOAD APP
Get the Kasa Smart app from the App Store or Google Play.

tp link HS200 2 Smart Wi Fi Light Switch - qr code http://www.tp-link.com/common/promos/app_kasa.html?ref=QRCode

ADD TO KASA

Set up the first switch:
Tap the button in the app and select Smart Switches > Smart Switch (Wi-Fi). Then follow the app instructions to complete setup.
Set up the second switch following the same steps.

THIRD-PARTY SERVICES
Kasa works with Alexa, Google Assistant, and other third-party services to control your switch by voice.
Go to Me > Third-Party Services in the Kasa Smart app to integrate the third- party services.
For step-by-step setup instructions, please visit:

Google Home Assistant: https://www.tp-link.com/support/faq/1534/
Amazon Alexa: https://www.tp-link.com/support/faq/944/

Specifications
Rating: 100-120V~ 50/60Hz
Max Load (Each Gang): 15 A General Use 600 W Incandescent/Halogen, 1/6HP Motor
In-Wall Depth: 0.98 in (25 mm)
Operation temperature: 0~40℃
Method of mounting included: Independently mounted (Vertically position only);
Operating control, Type 1.C action
Pollution Degree 2, Rated Impulse Voltage 2500V
Software Class A, NEMA Type 1

Recommended Load Types:

LED: ≤ 100W	Ceiling Fan: ≤ 120 W

CAUTION
High Voltage-Disconnect power supply at the circuit breaker before servicing

Safety Notice
Before installing, servicing or removing the switch, read and follow all safety precautions including the following:

CAUTION – Risk of Electric Shock – More than one disconnect switch may be required to de-energize the equipment before servicing. A circuit breaker which disconnects the Line and Neutral conductor simultaneously is suitable. Ensure power is off at the circuit breaker before removing or installing any switch. Use a non-contact voltage tester to ensure the power is off.
The Smart Switch must be installed and used in accordance with the National Electric Code (NEC) or your local electrical code. If you are unfamiliar with these codes and requirements, or are uncomfortable performing the installation, consult a qualified electrician.
Do not install the Smart Switch with wet hands or when standing on wet or damp surfaces.
Install only in a suitable UL Listed outlet box (suitable dimensions: H > 2.95 in./75 mm, W > 3.68 in./93.5 mm, D > 1.65 in./42 mm).

Support
For technical support, the user guide and other information, visit https://www.tp-link.com/support/.