Rilistenica A05271 5 Light Brass and Acrylic Resin Modern Contemporary Instruction Manual

June 1, 2024
Rilistenica

Rilistenica A05271 5 Light Brass and Acrylic Resin Modern Contemporary

Rilistenica-A05271-5-Light-Brass-and-Acrylic-Resin-Modern-Contemporary-
product

Introduction

Item Number: A05271

WARNING (To reduce the risk of fire, electric shock, or personal injury):

  1. We suggest installation by a licensed electrician.
  2. Please read the instruction carefully and save it as you may need it at a later time.
  3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
    • Go to the main fuse, or circuit breaker, box in your home.
    • Place the main power switch in the “OFF” position.
    • Place the wall switch in the “OFF” position.
  4. Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
  5. Make sure that the ceiling or wall can stand the weight of the lamp before installation.
  6. Make sure the voltage you are using is 120V. The maximum wattage is LED, 25W.
  7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
  8. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
  9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT

Rilistenica-A05271-5-Light-Brass-and-Acrylic-Resin-Modern-Contemporary-
fig-5

TOOLS REQUIRED (NOT INCLUDED):

Before starting assembly and installation please prepare the needed tools as below picture

PARTS AND ACCESSORIES

PARTS TYPE & QTY INCLUDED

Rilistenica-A05271-5-Light-Brass-and-Acrylic-Resin-Modern-Contemporary-
fig-2

  • (E) Mounting plate (1)
  • (F) Canopy screw (6)
  • (G) Canopy (1)
  • (H) Lock nut (5)
  • (I) Cable (5)
  • (J) Cover (5)
  • (K) Body (5)

ACCESSORIES & QTY ENCLOSED:

  • (A) Anchor (4)
  • (B) Mounting screw (2)
  • (C) Plastic Wire Connector (3)
  • (D) Anchor screw (4)

ASSEMBLY & INSTALLATION INSTRUCTIONS:

Rilistenica-A05271-5-Light-Brass-and-Acrylic-Resin-Modern-Contemporary-
fig-3

  1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.

  2. Turn off power
    Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.

    • Go to the main fuse, or circuit breaker, box in your home.
    • Place the main power switch in the “OFF” position.
    • Place the wall switch in the “OFF” position.
  3. Make installationRilistenica-A05271-5-Light-Brass-and-Acrylic-Resin-Modern-Contemporary-fig-3

    • Step A1
    • Unscrew canopy screws (F) from canopy (G).
    • Gently remove mounting plate (E) and then set them aside for later installation.
    • Step A2: Carefully pass the supply wires from the outlet box through mounting plate (E).
    1. NOTE: To drill the holes in the wall for anchors (A), attach mounting plate (E) to wall with screws ( B & D )
    2. Attach mounting plate (E) to outlet box and then mark the position of holes in the wall with a pen as shown in the illustration.
    3. Drill holes and gently knock anchors (A) into the marked holes until anchors (A) are level with the wall.
    4. Secure mounting plate (E) to the wall with screwing anchor screws (D) into anchors (A) and mounting screws (B) into holes of mounting plate (E).
    • Step A3: Make wire connections
    • Connect wires as shown in the charts below. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.Rilistenica-A05271-5-Light-Brass-and-Acrylic-Resin-Modern-Contemporary-fig-4..
    • Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.
    • Step A4
    1. Position canopy (G) in place.
    2. Carefully thread canopy screws (F) through the holes in canopy (G) and mounting plate (E) and then secure them by tightening canopy screws (F).
    • Step A5: Please adjust the hanging height of the fixture:
    • Press down and hold lock nuts (H) of canopy by hand.
    • Pull or push cables (I) in and out of canopies to increase or decrease the hanging height.
  4. Check that everything is installed properly, then you can turn on the light. We hope you enjoy your new lighting!

ORDERING PARTS AND CLEANING

ORDERING PARTS

  • Keep this sheet for future reference in case you need to order replacement parts.
  • All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.

CLEANING

  • To clean, wipe the fixture with a soft cloth. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals