Wanderer 668137 Instant Nightfall Tent 6p Installation Guide
- June 1, 2024
- Wanderer
Table of Contents
Wanderer 668137 Instant Nightfall Tent 6p
PARTS LIST
AWNING POLES
SET UP INSTRUCTIONS
CAUTION! When setting up and packing up the tent the poles
may twist and become difficult to slide. If this occurs DO NOT USE FORCE BY
PULLING ON THE POLES. Twist the poles gently until the flat parts of the poles
align ensuring the poles slide smoothly.
ATTENTION! When sliding the leg pole, do not press the push button.
Otherwise, the pole may detach and cause damage to the tent.
- STEP 1 Ensure the ground is free from sharp objects, unfasten the inner tent and let it spread out on the ground freely, and unfold the leg poles.
- STEP 2 With the help from another person, set up the tent roof first. Slide out the top poles until you hear “click”, the push button will pop up and the poles are now in place.
- STEP 3 Slide the leg poles out until you hear “click”, the push button will pop up and the poles will now in place. Peg down all peg points on the inner tent before moving to the next step.
- STEP 4 Take a flysheet and drape it over the inner tent with the door facing the correct direction. Secure the flysheet to poles using hook and loop tapes. Then peg down the remainder of fly. Using guy ropes provided peg out away from the tent to maximize stability.
- STEP 5 To assemble the awning use the steel poles and guy ropes provided. Pass the pole spigots through the eyelets on each corner of the door. Peg down with guy ropes to secure the poles.
WARNING
- Before using the tent for the first time, it is recommended to check all components have been included and you become familiar with the assembly of the tent by reading through the instructions first.
- DO NOT set up near an open flame. The fabric will burn if left in continuous contact with any flame source.
- DO NOT use any form of flame or fuel-burning appliances, heaters, candles or matches inside or under the canopy of the tent.
- Ensure your site is free from any objects and obstructions by checking the area and clearing away any rocks, tree branches or any sharp objects before setting up your tent.
- Keep away from any overhead power lines and do not set up under trees where there is the potential for either falling branches or lightning strikes to occur.
- The tent must be securely pegged to the ground using all the peg points provided. All guy ropes attached to the tent must be used at all times to create added stability and avoid possible damage to either property or persons.
- It is crucial to do this anytime you have the tent up to minimize the impact of unexpected wind gusts.
- Be cautious when handling the frame. Avoid pinching hands or fingers in any moving parts.
- Utility hooks are designed for small hanging objects only. Do not hang any object heavier than 2kgs. Check the hook every time before use. Do not use it if it comes loose!
- The set up of this tent is recommended as a two-person set-up.
- Keep children away from the set-up area.
- When removing the pegs from the ground, never pull on the tent to remove them. This may cause damage to either property or persons. Always pull on the peg itself.
- This tent is not designed to be a permanent or semi-permanent structure. It is designed to be used as a portable and temporary structure.
Care and maintenance
- The following are some helpful tips on how to clean and properly store your tent.
- Wash the frame and canopy with a mild solution of soap and water, rinse thoroughly. Dry completely. Do not use bleach or solvents.
- DO NOT spray insecticides or bug repellants directly or near any fabric. This may damage the water-repellent treatment.
- Always return the tent to the carry bag after use. Be sure the tent is completely dry before storing it.
- Never store the tent wet. If the tent is wet, please take it out from the storage bag as soon as possible and leave spread out to dry completely before storing it away.
- Due to cold air outside and warm air inside the tent, may develop condensation on the inside of the tent. This is a natural event and adequate ventilation will help minimise this.
CONTACT
- Manufactured & packaged for SRGS PTY LTD
- ABN 23 113 230 050
- 6 Coulthards Avenue, Strathpine QLD 4500, Australia
- MADE IN CHINA
- PLU: 668137
Read User Manual Online (PDF format)
Loading......