GADNIC PROJ0002 Wall Projector Screen Instruction Manual
- June 1, 2024
- GADNIC
Table of Contents
GADNIC PROJ0002 Wall Projector Screen
Specifications
| Brand | GADNIC |
|---|---|
| Technical Service | SERVITECH |
| Contact | 11 6260 1114 (text only), |
serviciotecnico@servitech.com.ar
Website| www.servitech.com.ar
Warranty| GADNIC Warranty
Introduction
Thank you for choosing our screens. All screens have passed a strict quality inspection before delivery. Please read this manual carefully to ensure proper use. You may also find solutions to problems here. It is important that electrical connections and the adjustment of the final race are made by qualified personnel.
Motorized Screen
1. Circuit Diagram
If the motorized screen works with a manual switch, consult the following figure for the electrical connection.2. End-of-Run Adjustments
Adjust the position of the end-of-run stops, consult the image below:3. Useful Instructions
- The screen must be connected to an appropriate power source.
- The screen can be used with or without a remote control.
- Normally, the synchronous motor is mounted in the housing.
- If not equipped with a remote control system, the screen can be directly managed through the control box buttons.
- The screen will automatically stop when raising or lowering if the screen reaches the end of the mesh or if the power cable is disconnected.
Installation
- Carefully disassemble the screen and ensure that it is in good condition, checking that all accessories are packaged within the box.
- Verify that the voltage and frequency indicated on the screen coincide with local power and recommended outlets.
- Refer to the following figure and attach the screen to the wall or ceiling.
Warnings
- Do not fold the screen. Avoid touching the screen surface with hard objects or fingers.
- If the power cable is damaged, it must be replaced by the manufacturer or an authorized technical service for safety reasons.
- After use, store the screen in a protective case to prevent it from wandering.
Remote Control System
The remote control can be of RF type or IR type. Instructions for pairing
and troubleshooting are included, such as what to do if the remote control LED
indicator does not flash after pressing the buttons.
Manual Wall Screen
- Structure
- Installation: Mobile parts of the actuation system should be installed at a height of more than 2.5 mm above the floor or any accessible height.
- Useful Instructions: Hold the traction ring firmly and pull the screen down slowly.
- Warnings: Do not fold the screen. Clean gently with a soft brush or dry cloth.
Tripod Screen
- Structure: Includes reinforced tripod for stability and durability.
- Installation: Choose a suitable location for installation and set up the tripod’s legs first.
- Useful Instructions: The tripod legs should be firmly closed.
- Warnings: Do not fold the screen. Clean the screen surface with a soft brush or dry cloth.
Technical Data
a. Matte White Screen
Gain: 1:1, Viewing Angle: 160°, High color reproduction, high resolution.b. Glass Fiber Screen
Gain: 2.5, Viewing Angle: 60°, High color reproduction, high resolution.c. Synchronous or Tubular Motor
High quality, fitted on the left end of the screen housing.d. Gain Measurement
Consult the following figure, standard: JB/T8389 issued by the Ministry of Industry of Machinery.e. Viewing Angle Measurement
Consult the following figure, standard: JB/T8389 issued by the Ministry of Industry of Machinery.FAQ
What should I do if my motorized screen is not responding?
Check the power source and ensure it matches with the local voltage and frequency. Refer to the circuit diagrams for troubleshooting.
How do I adjust the end-of-run stops on my screen?
Consult the adjustment diagram provided in the manual for instructions.
Can I use the screen without the remote control?
Yes, if the screen is not equipped with a remote control system, it can be directly managed through the control box buttons.
What maintenance is required after using the screen?
Store the screen in a protective case to prevent damage and clean the surface gently with a soft brush or dry cloth.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>