tp-link EAP225 Wall Plate Wi-Fi 6 GPON Access Point Instructions
- June 1, 2024
- tp-link
Table of Contents
tp-link EAP225 Wall Plate Wi-Fi 6 GPON Access Point
For Class B EAP with no adapter:
Product Name: Omada EAP
Model Number: EAP225-Wall / EAP235-Wall / EAP615-Wall / EAP615GP-Wall
Responsible party: TP-Link USA Corporation
Address: 10 Mauchly, Irvine, CA 92618
Website: https://www.tp-link.com/us/
Tel: +1 626 333 0234
Fax: +1 909 527 6804
E-mail: sales.usa@tp-link.com
FCC Compliance Information Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
- Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note
The manufacturer is not responsible for any radio or TV interference caused
by unauthorized modifications to this equipment. Such modifications could void
the user’s authority to operate the equipment.
FCC RF Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This device and its antenna must not be co-located
or operating in conjunction with any other antenna or transmitter. “To comply
with FCC RF exposure compliance requirements, this grant applies to only
Mobile Configurations. The antennas used for this transmitter must be
installed to provide a separation distance of at least 20cm from all persons
and must not be co-located or operating in conjunction with any other antenna
or transmitter.” We, TP-Link USA Corporation, have determined that the
equipment shown above has been shown to comply with the applicable technical
standards, FCC part 15. There is no unauthorized change is made to the
equipment and the equipment is properly maintained and operated.
CE Mark Warning
This is a class B product. In a domestic environment, this product may cause
radio interference, in which case the user may be required to take adequate
measures.
OPERATING FREQUENCY (the maximum transmitted power)
For EAP115-Wall
- 2412MHz—2472MHz(20dBm)
For EAP225-Wall / EAP230-Wall / EAP235-Wall / EAP615-Wall:
- 2412MHz—2472MHz(20dBm)
- 5150MHz—5250MHz(23dBm)
For EAP650-Wall / EAP655-Wall / EAP615GP-Wall:
- 2412MHz—2472MHz(20dBm)
- 5150MHz—5250MHz(23dBm)
- 5250 MHz -5350 MHz (23dBm)
- 5470 MHz -5725 MHz (30dBm)
EU Declaration of Conformity
TP-Link hereby declares that the device complies with the essential
requirements and other relevant provisions of directives 2014/53/EU,
2009/125/EC, 2011/65/EU, and (EU)2015/863. The original EU Declaration of
Conformity may be found at https://www.tp-link.com/en/ce.
RF Exposure Information
This device meets the EU requirements (2014/53/EU Article 3.1a) on the
limitation of exposure of the general public to electromagnetic fields by way
of health protection. The device complies with RF specifications when the
device is used at 20 cm from your body.
National Restrictions
For EAP225-Wall / EAP230-Wall / EAP235-Wall / EAP615-Wall / EAP650-Wall /
EAP655-Wall
EAP615GP-Wall:
Attention: This device may only be used indoors in all EU member states,
EFTA countries, and Northern Ireland.
Frequency band: 5150 – 5250 MHz: Indoor use: Inside buildings only.
Installations and use inside road vehicles and train carriages are not
permitted. Limited outdoor use: If used outdoors, equipment shall not be
attached to a fixed installation or the external body of road vehicles, a
fixed infrastructure, or a fixed outdoor antenna. Use by unmanned aircraft
systems (UAS) is limited to within the 5170 – 5250 MHz band.
Frequency band: 5250 – 5350 MHz
Indoor use: Inside buildings only. Installations and use in road vehicles,
trains, and aircraft are not permitted. Outdoor use is not permitted.
Frequency band: 5470 – 5725 MHz
Installations and use in road vehicles, trains, and aircraft and use for
unmanned aircraft systems (UAS) are not permitted.
UK Declaration of Conformity
TP-Link hereby declares that the device complies with the essential
requirements and other relevant provisions of the Radio Equipment Regulations
2017.
The original UK Declaration of Conformity may be found at
https://www.tp-link.com/support/ukca
National Restrictions
Attention: This device may only be used indoors in Great Britain.
Canadian Compliance Statement
This device contains license-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s license-exempt
RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may
cause undesired operation of the device.
For EAP615GP-Wall
The device meets the exemption from the routine evaluation limits in section
2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain
Canadian information on RF exposure and compliance. This transmitter must not
be co-located or operating in conjunction with any other antenna or
transmitter. This equipment should be installed and operated with a minimum
distance of 20 centimeters between the radiator and your body.
Caution
For EAP225-Wall / EAP235-Wall / EAP615-Wall / EAP615GP-Wall: The device for
operation in the band 5150–5250 MHz is only for indoor use to reduce the
potential for harmful interference to co-channel mobile satellite systems;
5150 MHz to 5350 MHz is restricted to indoor operations in Hong Kong.
Safety Information
- Keep the device away from water, fire, humidity, or hot environments.
- Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.
- Do not use the device where wireless devices are not allowed.
- Operating Temperature: 0℃ ~ 40℃ (32 ℉ ~ 104 ℉ )
- For EAP615GP-Wall:
Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or damage will occur due to improper use of the device. Please use this product with care and operate at your own risk.
Explanation of the symbols on the product label
Note: The Equipment marking is at the bottom of the device. Symbols may
vary from product.
Mounting Requirements
For safety, we recommend you use the original screws in the package when
mounting. The following are alternatives to mount the device on the wall:
- (For EAP115-Wall / EAP230-Wall) Use an 86 mm/standard EU wall junction box and 2 screwswhich comply with ANSI B1.1 4# or 6# standard and are longer than 15 mm.
- (For EAP225-Wall / EAP235-Wall) Use an 86 mm/standard EU/standard US wall junction box and 2–4 screws that comply with ANSI B1.1 4#, 6#, or 8# standard and are longer than 8.5 mm.
- (For EAP615-Wall / EAP650-Wall / EAP655-Wall / EAP615GP-Wall) Use an 86 mm/Standard EU/standard US wall junction box and 2–4 screws that comply with ANSI B1.1 4#, 6#, or 8# standard and are longer than 10 mm.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>