HWM MAN-153-0003-D SonicSens 3 Water Ltd Monitor Networks Instruction Manual
- June 1, 2024
- HWM
Table of Contents
HWM MAN-153-0003-D SonicSens 3 Water Ltd Monitor Networks
Product Information
Specifications
- Manufacturer: HWM-Water Ltd
- Product Models: SonicSens 3 (SONIC3/06//IS), SonicSens 3(SONIC3/10//IS)
- Compliance: EU Directives, UK Statutory Instruments, FCC Regulations
Product Usage Instructions
Safety Information
When using the product, ensure to follow all safety guidelines provided in the user manual to prevent any accidents or injuries.
Handling and Disposal
Dispose of Waste Electrical and Electronic Equipment and batteries responsibly according to local regulations. Do not dispose of them as normal domestic waste. Take them to designated collection points for safe handling and recycling.
Returning Equipment
Customers are responsible for returning waste electrical and electronic equipment to HWM-Water Ltd. Follow the provided instructions for returning the equipment.
Regulatory Compliance
The equipment complies with applicable EU Directives and UK Statutory Instruments. For full declarations of conformity, visit www.hwmglobal.com /product-approvals/
FCC Compliance
The product models SonicSens 3 comply with FCC regulations. Operation is subject to specific conditions to avoid interference.
FAQ
- Q: How do I dispose of Waste Electrical and Electronic Equipment?
- A: Dispose of the equipment at designated collection points for safe handling and recycling according to local laws.
- Q: Who is responsible for returning waste electrical equipment?
- A: Customers are responsible for returning waste electrical and electronic equipment to HWM-Water Ltd.
Safety Warnings and Approvals Information
This document applies to the following family of devices:
- SonicSens 3 (SONIC3/06/*/IS)
- SonicSens 3 (SONIC3/10/*/IS)
SAFETY
- Carefully read the information in this document and on the packaging before using the product. Retain all documentation for future reference.
- WARNING: When this equipment is being used, installed, adjusted or serviced this must be undertaken by suitably qualified personnel familiar with the construction and operation of the equipment and the hazards of any utility network.
- When installing in an ATEX environment, ensure only ATEX approved logger, sensors and accessories are used (check each product label to confirm). Ensure accessories are compatible with the equipment. Refer to the user guide for more information.
- When used in an ATEX environment, this equipment must be installed by a fully ATEX trained installer.
- CHOKING HAZARD – Contains small parts. Keep out of the reach of small children.
- Designed for outdoor use in areas that may become flooded resulting in the equipment becoming soiled. Wear appropriate protective clothing when installing or removing the product from the installation site. Protective clothing is also required when cleaning the equipment.
- Do not disassemble or modify the equipment. Contains a seal to protect against water and moisture ingress. Water ingress may cause damage to equipment.
Use and Handling
- The equipment contains sensitive parts that can be damaged by incorrect handling. Do not throw or drop the equipment or subject it to mechanical shock. When transporting in a vehicle, ensure the devices are secured and adequately cushioned, so they cannot fall and so that no damage can occur.
- Install equipment securely, using the brackets, as described in the user-guide.
- No user-serviceable parts inside. The equipment must only be serviced or disassembled by the manufacturer or its authorised repair centre.
- Normal operating temperature: -20°C to +60°C. Do not expose to direct sunlight for prolonged periods. Do not mount on apparatus that can exceed this temperature range
- Hold the main body of the unit when carrying. DO NOT carry by the cable as this can cause permanent damage and is not covered by warranty.
- tore unused equipment in the original packaging. The equipment can become damaged by applying heavy loads or forces to it.
- The equipment may be cleaned by use of a soft cloth lightly moistened with a mild cleaning fluid (e.g. a diluted domestic dish-washing liquid). A disinfectant solution may be used to sanitise if required (e.g. a diluted domestic disinfectant). For heavy soiling, gently remove debris with a brush (e.g. a domestic dishwashing tool, or similar). Ensure all connection points have a water-tight cover attached during cleaning, to prevent water ingress. When the connectors are not in use, keep the inside of the connectors clean. Do not allow liquid, moisture, or small particles to enter the equipment or connector. Do not pressure-wash as it may damage the equipment.
Waste Electrical and Electronic Equipment and the Battery Directive
Disposal and recycling: When the equipment or its batteries reach the end of their useful life, they must be disposed of responsibly, according to any applicable country or municipal regulations. Do not dispose of Waste Electrical and Electronic Equipment or batteries as normal domestic waste; they must be taken by the user to a separate waste collection point designated for safe handling and recycling in accordance with local laws. Waste Electrical and Electronic Equipment and batteries contain materials that, when correctly processed, may be recovered and recycled. Recycling product reduces the need of new raw materials and also reduces the amount of material that is sent for disposal as landfill. Improper handling and disposal can be harmful to your health and the environment. For more information regarding where the equipment can be accepted for recycling, please contact your local authority, recycling center, distributor or visit the website http://www.hwmglobal.com /company-documents/ Waste Electrical and Electronic Equipment. HWM-Water Ltd is a registered producer of Electrical and Electronic Equipment in the United Kingdom (registration number WEE/AE0049TZ). Our products fall under category 9 (Monitoring and Control Instruments) of The Waste Electrical and Electronic Equipment Regulations. We take all environmental issues seriously and fully comply with the requirements for collection, recycling and reporting of waste products.
HWM-Water Ltd is responsible for Waste Electrical and Electronic Equipment from customers in the United Kingdom provided that:
The equipment was produced by HWM-Water Ltd (Palmer Environmental / Radcom Technologies / Radiotech / ASL Holdings Ltd) and supplied on or after 13th August 2005. or The equipment was supplied before 13th August 2005 and has been directly replaced by HWM-Water Ltd products manufactured since 13th August 2005.
HWM-Water products supplied after 13th August 2005 can be identified by the following symbol:
Under HWM-Water Ltd.’s Terms and Conditions of Sale, customers are responsible for the cost of returning waste electrical and electronic equipment to HWM- Water Ltd and we are responsible for the costs of recycling and reporting on that waste.
Instructions for returning Waste Electrical and Electronic Equipment:
- Ensure that the Waste Electrical and Electronic Equipment meets one of the two conditions above.
- Return the Waste Electrical and Electronic Equipment to HWM-Water Ltd.
In accordance with the regulations, customers outside the United Kingdom are responsible for Waste Electrical and Electronic Equipment.
A licensed waste carrier must be used for transporting all waste. For more information on Waste Electrical and Electronic Equipment compliance or the Battery Directive please e-mail [email protected] or phone +44 (0)1633 489 479
Regulatory Compliance Statement:
Hereby, HWM-Water Ltd declares that this equipment is in compliance with applicable EU Directives and the relevant UK Statutory Instruments requirements. A copy of the full text of the UK and EU declarations of conformity is available at the following URL: www.hwmglobal.com/product- approvals/
FCC Statement
FCC Compliance Information
Fluid Conservation Systems,
- 1960 Old Gatesburg Road, Suite 150,
- State College, PA 16803
- T: 1-800-531-5465
The following product models: SonicSens 3 (SONIC3/06//IS) SonicSens 3 (SONIC3/10//IS) Comply with the rules, as applicable.
FCC compliance statement:
- This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
Industry Canada – Compliance Statement:
This Class A digital apparatus complies with Canadian ICES-003. CAN ICES 003A / NMB 003A
Contact
- HWM-Water Ltd Ty Coch House Llantarnam Park Way Cwmbran NP44 3AW United Kingdom
- +44 (0)1633 489479
- www.hwmglobal.com
©HWM-Water Limited. This document is the property of HWM-Water Ltd. and must not be copied or disclosed to a third party without the permission of the company. Copyright reserved.
References
- Convenient Water Delivery Near You | Primo Water Delivery
- HWM | Energy Management, Pressure Control, Data Collection, Environmental Monitoring, Leak Detection,