Tilta TA-LSP8-B Left Side PD Handle With Run/Stop Type VIII Black Instruction Manual
- June 13, 2024
- TILTA
Table of Contents
- Tilta TA-LSP8-B Left Side PD Handle With Run/Stop Type VIII Black
- DISCLAIMER
- WARNINGS AND PRECAUTIONS
- OVERVIEW
- Specification
- Paking List
- BATTERY USAGE NOTES
- PRODUCT HIGHLIGHTS
- Description
- INDICATORS
- OPTIONAL ACCESSORY LIST
- INSTALLATION
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Tilta TA-LSP8-B Left Side PD Handle With Run/Stop Type VIII Black
DISCLAIMER
Thank you for choosing Tilta products.
-
Please read this user guide carefully before using the product to ensure the correct product settings have been applied. The final interpretation right of this article and the products belong to Tilta . We reserve the right to update without prior notice. Please visit www.tilta.com for the latest product information.
-
Once you use this product. it is deemed that you have carefully read thedisclaimer and warning, and understand, recognize and accept all terms and contents of this statement. You assume full responsibility for the use of this product and the possible consequences. You agree to use this product only for legitimate purposes and also agree to these terms and any relevant regulations, policies and guidelines formulated by Tilta.
Tilta is not responsible for damages, injuries and any legal liability arising directly or indirectly from the use of this product. Users should follow all safety guidelines including but not limited to those mentioned in this article. -
Even if the above provisions exist, consumer rights are still protected by local laws and regulations and are not affected by this disclaimer.
-
Tilta is a registered trademark that belongs to Tilta technology Co., Ltd and its subsidiary company. All product and brand names that are mentioned in this content belong to Tilta technology Co., Ltd and its subsidiary company.
WARNINGS AND PRECAUTIONS
Heat generation, spontaneous combustion, explosion, etc., may occur due to improper operation while using this product. Otherwise, performance degradation and failure may occur, so please observe the following prohibitions and precautions.
- This product charges digital cameras, notebooks, and mobile phones, and is suitable for various application scenarios. Consult our company if you need to use ii for other devices.
- Do not try to short-circuit the product.
- Do not transport or store it along with metallic objects.
- When carrying the battery onto a plane, do not place it near a conductive liquid. Do not throw the battery into water, fire, or heat.
- Do not place the battery in a high-temperature area, such as in a car or under the hot sun, and do not charge, discharge, or store it in an environment exceeding the operating temperature range (see •Battery Usage Instructions”).
- Do not disassemble or modify the battery.
- Do not drop the battery or hit it with a hammer to avoid any substantial impact. Also, stop using the battery if the damage is evident.
- Do not use the battery in a corrosive environment (salt, seawater, acid, alkali, corrosive gas, etc.).
- Do not use and store the battery in extremely high-humidity environments.
PRECAUTIONS
- If the battery cannot be fully charged within the specified charging time, please stop charging immediately.
- When charging or discharging, please stop charging immediately if the battery has an abnormal smell, heat, discoloration, deformation, and other symptoms that are different from the normal state.
- When the battery leaks or smells, please keep the battery away from fire.
- Before using it tor the first time after purchase, remember to fully charge it before using it.
- When not used for more than two days, the battery will automatically turn off the output. Before using ii again, you need to press the power button before it can be used or charged again.
- For long-term storage, please charge the battery regularly (about once every two months) to keep the battery’s power at the state where the green light is on.
This product has been strictly inspected before leaving the factory. If there is any problem, please get in touch with the company’s after-sales service. Refrain from disassembling by yourself.
OVERVIEW
Specification
- MATERIAL: Aluminum
- WEIGHT: 502.5g
- DIMENSIONS: 117X93X71mm
- COLOR: Black
Paking List
BATTERY USAGE NOTES
BATTERY CAPACITY
14.4V 50Wh 3500mAh
- Working temperature: 0°C ~ 45°Cfor charging; -20°C ~ 60°C for discharging
- Storage temperature: -20°C – 45°C
- Operating humidity: 90-95%(Max.)
- Relative storage humidity: ≤ 70%RH
- Warranty: 12months AND with less than 200 full usage cycles.
PRODUCT HIGHLIGHTS
PD Fust Chorging
(If USB-C the camera cable. The supports camera PD can also protocols, be the
powered camera through can be the powered dummy through batteries.) the USB-C
to USB-C cable. The camera can also be powered through the dummy batteries.)
Dummy Battery Cables: [Optional]
- Canon LP-E6 Dummy Battery to USB-C PD Power Cable DB-LPE6-USBC
- Sony NP-FZ100 Dummy Battery to USB-C PD Power Cable DB-SYFZ-USBC
- Panasonic DMW-BLF19 Dummy Battery to USB-C PD Power Cable DB-GH-USBC
Flexible Adjustmen
(Press the release to adjust the angle)
Ergonomic Design
(Comfortable operation)
Cold Shoe Mount
For mounting accessories with a cold shoe mount)
1/4″-20 Screw with Locating Points
(For mounting accessories with 1/4″-20 screw with locating pins)
Run/Stop
(Pair with the approriate R/S cable to control the camera’s run/stop)
Description
-
Power/Rec Button (0l’VOff: Hold for 2s) (Rec: Single dick white the camera is on.)
-
Safety Release (Press to adjust handle’s anije.)
-
NATO Mount Attachment
(Other attachments available) -
Tie Down
-
USB-C Port
-
USB-C PD Port
-
M3 Screw
(For adjusting the height of the USB-C cable clamp.) -
Cable Clamp for USB-C Cable
-
M3 Screw (For holding the USB-C cable.)
-
USB-C Signal Indicator
-
USB-C PD Battery Indicator
-
Wrist Strap Port
-
Cold Shoe Mount
-
Hex Key
(For adjusting the M3 screw. Can be attached to the bottom of the handle.) -
1/4″-20 Screw with Locating Points
-
Wrist Strap Port
USB-C Usage Notice [Do not short circuit through the USB-C Output.]
USB-C PD
Support PD 3.0 and PD 2.0 1/0 fast charging protocol.
USB-C
Tilta Series Product
USB-C OUTPUT VOLTAGE
12.0V~16.8V (Max 1.5A)
TheUSB·Cponiscompa1iblewithli1toR/Scables.
- Canon R5/R5C and BMPCC 4K /6K/6K PRO support Type-C input. No additional purchase needed.
- RS-TA3-AM3 Advanced Side Handle Run/Stop Cable for 3-Pin Fischer port
- RS-TA3-AM7 Advanced Side Handle Run/Stop Cable for Arri 7-Pin EXT port
- RS-TA3-SY Advanced Side Handle Run/Stop Cable for 4-Pin Hirose port
- RS-TA3-KF Advanced Side Handle Run/Stop Cable for Kinefinity Cameras
- RS-TA3-LANC Advanced Side Handle Run/Stop Cable for 2.5mm LANC Port
- RS-TA3-GHS Advanced Side Handle Run/Stop Cable for Panasonic GH/S Series
- RS-TA3-RD3 Advanced Side Handle Run/Stop Cable for Red Camera SYNC Port Туре Il
- RS-TA3-RD1 Advanced Side Handle Run/Stop Cable for Red Camera SYNC Port Type I
- RS-TA3-SYA Advanced Side Handle Run/Stop Cable for Sony ab/a7/a9 Series
- RS-TA3-RD2 Advanced Side Handle Run/Stop Cable for Red Camera CTRL Port
- RS-TA3-FJX Advanced Side Handle Run/Stop Cable for Fujifilm X Series
- RS-TA3-RD4 Advanced Side Handle Run/Stop Cable for Red Komodo Camera
- RS-TA3-CND Advanced Side Handle Run/Stop Cable for Canon DSLR
- RS-TA3-CNC Advanced Side Handle Run/Stop Cable for Canon C series
- RS-TA3-USBC Advanced Side Handle Run/Stop Cable for USB-C Port
INDICATORS
USB-C PD Bottery Indicotors
-
Discharging Signal
- Red light flashes:
- Red light stays on:
- Green light stays on:
- Blue light stays on:
-
Charging Signal
[It takes approximately 2 hours to fully charge with a 60W PD fast charger. ]- Blue light flashes: charging
- Blue light stays on: fully charged
-
Firmware Upgrade (When needed)
-
Firmware Upgrade (When needed)
Download and upgrade the firmware from the Tilta official website and complete the installation. If you have any installation questions, please consult the official customer service of Tilta. (Tilta official website: www.tilta.com)
INSTALLATION
- Power on, after the blue light is on (non-charging state), press the [on/off] button five times in a row;
- Wait for the battery indicator to show the flashing state of the three-color light , and enter the firmware upgrade mode;
- Connect the USB-C PD interface of the handle to the computer through the USB Type-A to USB-C data cable, and copy the upgraded firmware to the handle program;
- After the three-color light stops flashing, the upgrade is complete, and the blue light flashes.
USB·C Comm11nicotion Indicators (When aTilla cabte is detected, the indicator wilt tight up.)
- Green light stays on: Standby
- Red light stays on: Record
OPTIONAL ACCESSORY LIST
Please choose the side handle attachment according to your setup. To find the appropriate mount for your setup, please contact Tilta’s customer support.
NOTE:
Install the attachment according to its mounting port.
INSTALLATION
Take the Tilta full camera cage as an example.
- Slide (1) the NATO attachment for left side PO handle onto the NATO rail.
- Tighten (2) the tie down.
For further information Please visit www.tilta.com.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>