Jovial 5000.1 One Channel Car Audio Mono Amplifier User Manual

Jovial 5000.1 One-Channel Car Audio Mono Amplifier

DESCRIPTION

A high-powered amplifier, the Jovial 5000.1 One-Channel Car Audio Mono Amplifier is designed to improve the quality of the audio experience that passengers have when traveling in vehicles. It is optimized for powering a single subwoofer or bass speaker when configured with a single channel, sometimes known as a mono setup. This amplifier has a rating of 5000 watts, which allows it to send a substantial amount of power to the connected speaker. This results in a bass performance that is both deep and dramatic. It is designed to improve the reproduction of low-frequency sounds, which results in a sound that is fuller and more enveloping when played through automotive audio systems. The Jovial 5000.1 amplifier is a potent addition for audiophiles who are looking to improve their in-car audio setup, particularly with regard to the quantity and quality of bass that is produced.

SPECIFICATIONS

• Item Dimensions LxWxH: 12.3 x 10.6 x 2.4 inches
• Brand: Jovial
• Number of Channels: 1
• Item model number:  5000.1
• Total Audio Power Output: 14.4
  • 1 Ohm: 6200 Watts RMS
  • Total Audio Power Output: 14.4
  • 2 Ohms: 4300 Watts RMS
  • Total Audio Power Output: 12.6
  • 1 Ohm: 5500 Watts RMS
  • Total Audio Power Output: 12.6
  • 2 Ohms: 3600 Watts RMS, Efficiency
  • 2 Ohms: 77%, Efficiency
  • 1 Ohm: 67%, Input Voltage: 9 to 15 Volts
• Input Impedance: 100K Ohms
• THD+Noise: Less than 1%
• Input Sensitivity: 40mV to 2 Volts
• SNR: 90dB
• Frequency Response (Key OFF): 5 to 5KHz (-3dBs)
• Frequency Response: 20 to 5KHz (-3dBs)
• Bass Boost @ 45Hz: Variable 0 to +18dBs
• HPF (Subsonic): 20 to 80Hz  12dB/octave Linkwitz-Riley
• LPF (Crossover): 80 to 5kHz @ 12dB/octave Linkwitz-Riley
• Recommended Fuse: 250 Amps
• Current at Rest: 3.5 Amps
• Average Current Draw (Sinusoidal): 600 Amps
• Average Current Draw (Music): 270 Amps
• Power Wire Gauge (Minimum Recommended): 50mm / 0 AWG
• Weight: 12.25 lbs.

WHAT’S IN THE BOX

• Car Audio Mono Amplifier
• User Manual

DIMENSIONS

FEATURES

• MAXIMUM POWER OUTPUT OF 6200 WATTS:
  The bass boost, high pass filter, and low pass filter are all included with the 6200-watt one-channel high-power mono amplifier for automobile audio. It also has 270 amps for the current demand while it is operating at maximum power, which is sufficient for the majority of music programs.

• PERFECT FOR THE AUDIO ENTERTAINMENT IN THE CAR:
  This car amplifier provides you with the ultimate entertainment system, making it suitable for vehicle rides and lengthy rides with friends and families. It features our car audio mono amplifier, which strives for excellence and produces music that is both crisp and loud.

• MOUNTING HARDWARE TO MAKE THE INSTALLATION QUICK AND EASY:
  The ease of installation for the car audio mono amp’s users is ensured by the inclusion of all of the necessary mounting hardware that is included in the package. Indicators for power on (green), low battery (red), and clip short (blue) are also included on the amplifier.

• PROTECTION AGAINST SHORTCIRCUITS:
  This one-channel car amplifier has a fuse with a recommended rating of 250 amps installed in it so that it can protect itself as well as the electrical system in your vehicle from overheating, overloading, and short-circuiting. Maintains the security of both your automobile and its amplifier

• SLIM FIT CONSTRUCTION:
  This box amp’s modest size makes installation a breeze; you won’t have any trouble finding a location for this small yet powerful device because its dimensions are 12.3 inches long, 10.6 inches wide, and 2.4 inches high in inches. In addition, cooling fans are included to protect the device from overheating.

System Diagram

CONNECTIONS

• Connection to the Power Source:
  Make the connection between the positive (+) terminal of the amplifier’s power input and the positive terminal of the battery in your car. Establish a connection between the amplifier’s negative (-) power input terminal and a stable ground point located within the vehicle. To meet the power requirements of the amplifier, make sure the power and ground cables you use have the suitable gauge. For added protection, think about adding an inline fuse next to the battery.

• Connection for Remote Turn-On of Appliances:
  Join the wire for the remote turn-on function that is located on your head unit or other audio source to the terminal that is located on the amplifier. Activating and deactivating the amplifier in tandem with your audio system is communicated through this cable.

• Connection for the Audio Input:
  Make the connection between the audio input on the amplifier and the matching RCA outputs on your head unit or other audio source by using RCA cables. This input is where the audio signal that will be amplified by the amplifier is received.

• Speaker Connection to the Output:
  Connect the speaker wires coming from the amplifier’s speaker output terminals to the terminals on your subwoofer(s) or speakers that are corresponding to those on the amplifier. Be sure that the positive and negative terminals are connected in the correct order.

• Line Output Converter (LOC):
  In the event that your head unit does not come equipped with RCA outputs, you may be required to make use of a line output converter in order to change the speaker-level outputs from the head unit into RCA outputs for the amplifier.

• Adjustment of the Subwoofer:
  You will need to adjust the gain, crossover frequency, and any other settings on the amplifier so that they correspond to the requirements of the subwoofer you are using and the audio arrangement you want to achieve.

• Connection to the Ground:
  Connecting the ground terminal of the amplifier to a metal spot on the chassis of the car will provide a reliable ground connection that is also free of contaminants. This connection is necessary for the amplifier to function in the correct manner.

• Positioning of the Amplifier:
  Install the amplifier in a dry, well-ventilated space where it won’t be subjected to conditions that could damage it, such as high temperatures or prolonged exposure to the sun. Make sure the amplifier is secured securely so that it doesn’t slide about while you’re driving.

• Warnings and Precautions:
  Before beginning any wiring on your vehicle, you must first disconnect the negative connection of the battery to reduce the risk of electrical risks and short circuits.

PRECAUTIONS

• Learn from the Guide:
  Before attempting to install or make use of the amplifier, it is imperative that the user handbook and installation guide provided by the manufacturer be well studied and comprehended.

• Installation Done by Professionals:
  If you do not have experience installing car audio, you should think about getting assistance from a professional installer in order to ensure that the installation is done correctly and safely.

• Management of Power:
  Maintain compliance with the power handling specifications and advice provided by the amplifier in order to avoid overloading both the amplifier and the electrical system of your vehicle.

• Gauge of the Wiring:
  In order to match the power output of the amplifier, you will need to use the appropriate gauge of wiring for the power, ground, and speaker connections. Wiring that is not up to par can result in decreased performance, increased temperature, or even a fire.

• Protection for the Fuse:
  Installing the correct fuse on the power wire that is located close to the battery will protect the amplifier as well as the electrical system of the car from any potential overloads or short circuits.

• Getting a Grip:
  Make sure that the ground connection on the amplifier is stable and firmly attached to a spotless metal surface that is located on the chassis of the car. A substandard ground may result in unwanted noise as well as performance problems.

• A ventilation system:
  Install the amplifier in a location that has adequate ventilation to prevent it from overheating. It is important to refrain from covering the amplifier with anything that could impede airflow.

• Installation of the Amplifier:
  Mounting the amplifier securely will prevent it from moving around or vibrating while you are driving, both of which can cause unwanted noise and cause harm to the amplifier.

• Avoid Any Contact With Water:
  In order to prevent any damage or electrical risks, you should keep the amplifier away from water, dampness, and any other liquids.

• Stay Away From Hot Temperatures:
  Take care not to subject the amplifier to temperatures that are too high, since this could compromise its functionality and shorten its lifespan.

• Having the Right Connections:
  To avoid having connections that are either loose or incorrect, it is important to verify each one twice to ensure that it is accurate and securely attached.

• Speaker Compatibility:
  To avoid any damage and get the best possible performance from the amplifier, check that the impedance of its output matches the impedance of the subwoofer or speaker that is connected to it.

• Make the Necessary Settings Adjustments:
  Adjust the parameters on the amplifier, such as the gain, crossover frequencies, and bass boost, so that they correspond to the rest of your audio equipment and prevent distortion and damage.

• Examine the Wiring:
  Wiring, connections, and components should all be subjected to routine inspections to confirm that they are in sound shape and are unharmed.

• Responsible Driving:
  Make sure that the installation will not impede your ability to drive the vehicle safely and will not get in the way of your visibility.

FREQUENTLY ASKED QUESTIONS

What is the Jovial 5000.1 One-Channel Car Audio Mono Amplifier?

The Jovial 5000.1 is a mono car audio amplifier designed to power subwoofers and enhance the bass performance in your car's audio system.

What is the power output of the Jovial 5000.1 amplifier?

Is the Jovial 5000.1 amplifier a Class D amplifier?

The amplifier is likely a Class D amplifier, which is known for its efficiency in delivering high power to subwoofers.

What is the main purpose of the Jovial 5000.1 amplifier in a car audio setup?

The primary purpose of this amplifier is to provide a powerful and clean signal to drive subwoofers, enhancing the low-frequency response.

Does the Jovial 5000.1 amplifier support variable low-pass and subsonic filters?

Many mono amplifiers offer adjustable low-pass filters and subsonic filters to fine-tune the bass response.

Can the Jovial 5000.1 amplifier be bridged to power multiple subwoofers?

Mono amplifiers are typically not designed for bridging, as they are meant to power a single channel, usually for subwoofers.

What type of wiring and power connections are required for installation?

The installation typically requires proper power and ground wiring, as well as RCA cables for audio input.

Is the Jovial 5000.1 amplifier stable at lower impedance loads?

Does the Jovial 5000.1 amplifier include any protection features?

Many car amplifiers include protection mechanisms like thermal protection and short circuit protection to prevent damage.

Is the Jovial 5000.1 amplifier suitable for both casual listeners and car audio enthusiasts?

This amplifier is particularly appealing to car audio enthusiasts who want to achieve powerful and impactful bass.

Is professional installation recommended for the Jovial 5000.1 amplifier?

Professional installation is recommended to ensure proper wiring, setup, and optimal sound quality.

Does the Jovial 5000.1 amplifier support remote bass level control?

Some amplifiers offer remote bass level control to adjust the subwoofer output from the driver's seat.

Can the Jovial 5000.1 amplifier be used with factory car stereos?

Yes, the amplifier can be integrated with factory car stereos, but you might need appropriate adapters for proper connectivity.

Is the Jovial 5000.1 amplifier energy-efficient?

While Class D amplifiers are generally more energy-efficient than other classes, the amplifier's efficiency can vary.

Can the amplifier be used in addition to existing car audio components?

Yes, the Jovial 5000.1 amplifier can be integrated with existing car audio systems, enhancing the bass performance.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>