Cobra CPJS1000A Jump Starter User Guide
- June 12, 2024
- Cobra
Table of Contents
Jump Starter 1000A
Lithium-lon Jump Starter & Power Bank
With Fast Charge USB
FULLY CHARGE FIRST!
For optimal performance, charge
your Cobra Jump Starter prior to first use and every 12 months.
QUICK START GUIDE
Thank you for purchasing the Cobra Jump Starter 1000A
Jump start your vehicle’s dead battery and keep your portable devices powered
and charged with this heavy-duty Lithium-lon jump starter and power bank.
Fast charge USB ports allow you to charge multiple portable devices at once,
while two starting options allow you to start your vehicle either from direct-
to-bat- tery connection or through the in-car connection using the 12V outlet
inside your vehicle. Keep this in your
vehicle for when you or others will need it!
Count on Cobra for Power When You Need It.
Download the full Cobra Jump Starter 1000A manual at: cobra.com/manuals
Cobra® and the snake design are registered trademarks of Cobra Electronics
Corporation, USA.
Cobra Electronics Corporation™ is a trademark of Cobra Electronics
Corporation, USA.
Other trademarks and trade names are those of their respective owners.
©2021 Cobra Hlectronics Corporation
Jump Starter 1000A Features
A. LED Display
B. Power/Flashlight Button
C. Jump Start Connector
D. LED Flashlight
E. USB-C Fast Charge Input/Output| F.(2) USB-A Fast Charge Outputs
G. 12V Jump Start Connector
H. Jump Start Cable
I.USB-C to USB-A Cable
J.12V Jump Start Cable
---|---
Jump Starting Your Vehicle: Direct-to-Battery
- Connect the jumper cable clamps to the battery terminals (First, Red to Positive, then Black to Negative)
- Connect the jumper cables to the Jump Starter 1000A
- Walt for the Green LED light to appear on the Jump Start cable and then start your vehicle
- Disconnect the jumper cable from the Jump Starter 1000A and then from the battery
Jump Starting Your Vehicle: In-Car
-
Turn off all vehicle accessories.
Gonnect the jumper cable to the Jump Starter 1000A -
Depending on your vehicie, push the START button to Accessory mode or tum the ignition switch to the Accessory position
-
Gonnect the jumper cable plug into the vehicle’s 12V accessory port
NOTE : The 12V plug is used for in-car jump starting only. For instructions on recharging the Jump Starter 10004, please see
*Re-Charging Your Jump Starter 1000A” -
Wait for Output Ready and 5 solid charging bars on your Jump Starter’s LED screen and then start your vehicle.
-
Disconnect the Jump Start cable from the 12V accessory port and from the Jump Starter 1000A.
Leave the engine running for at least twenty mintes to allow the vehicle’s batery to recharge.
NOTE: The in-car battery charging from the Jump Starter 1000A will take up to 15 minutes.
If your vehicle does not start with the in-car method, ry the direct-to- battery method
Charging Your Devices
Re-Charging Your Jump Starter 1000A
In-Car Jump Starting FAQ
How do | know if my battery is charging?
When the 12V jumper cables are plugged into the Jump Starter 1000A and vehicle's 12V accessory port, the LCD screen will show a flashing 5-bar graph and the word ‘Output’. AS your battery charges the flashing bars will begin to tum solid until the vehicle is ready to star, at which point a ‘Ready’ message will appear on the screen and you are ready to start your vehicle
How long wil it take to charge?
In-Gar jump starting wil take longer than jump starting with a direct-to- battery connection, up to 5 minutes total. If your vehicle does not start with the in-car method, try to jump start with the direct-to-battery method,
What if| don't see the charging bars?
Ifthe Jump Starter 1000A does not have enough charge to jump start from vithin the car, the curtent battery percentage wil flash and a caution image will appear.In hat case you wil need tojump start your vehicie by using the direct- to-battery method
Tri-Color Status LEI
‘The Status LED williluminate and the color will change if the following conditions are present
| LED | CONDITION |
|---|---|
| No LED | Connection not detected or the Jump Starter 1000A battery is depleted. |
Check the battery charge level and verity the connection of the jumper cable
to the Jump Starter 1000A.
Solid Red| Reverse polarity connection. Reverse the damps.
Flashing Red| Over-current protection. Wait for 30 seconds and then retry
cOnnection.
Solid Yellow| Solid contact established and charging for jump start.
Flashing Yellow| Either the cables are not properly connected or the Jump
Starter 1000A is too hot. Remove cable and retry connection.
Red and Green Flashing Alternatingly| Safety feature to prevent the battery
from overheating from too many jump start attempts in a short period of time.
Remove cable and wait a few minutes.
Solid Green| Ready to jump start your vehicle.
NOTE : Whnen connected to your vehice’s battery and charging, the Jump Starter 1000A wil make a cicking sound every 5 seconds. This is part of normal operation.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>