Handan Beiku Intelligent Technology Co LTD ZH20241001 Battery Operated Children Car Instruction Manual
- June 1, 2024
- Handan Beiku Intelligent Technology Co LTD
Table of Contents
- Beiku Intelligent Technology Co LTD ZH20241001 Battery Operated Children
- Specifications
- Charging points
- Trouble shooting
- Instructions for use
- Remote control functions and instructions
- Precautions for use
- Packing Instruction
- Instructions
- FCC Statement
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Beiku Intelligent Technology Co LTD ZH20241001 Battery Operated Children
Car
Thank you for choosing our electric baby carriage
Please read the manual before using this product, it will tell you the correct
operation method and installation steps. To avoid incorrect operation of the
product and damage or injury to your baby. This manual shall be properly kept
and kept in an accessible place.
Specifications
Storage battery | 12V 4.5Ah |
---|---|
Motor | 12V380*2 |
Applicable Age | For children aged 37-95 months |
Maximum load | 25kg |
Dimensions | 108x62x40CM |
Speed | 3km/h |
Charger | Input: 100V-240V Output: 12V800mA |
Usage time | Charge for 10-12 hours. Use for 1-2 hours |
Charging points
- When using an electric car for the first time, the battery must be fully charged for 16 hours! Otherwise the battery will be permanently damaged and beyond repair The charging timeshould not exceed 18 hours.
- When charging, first plug the charger DC into the charging socket, and then plug the charger into the power socket.
- Each continuous use of 1 hour, you must be timely charging, normal charging time for 10-12 hours.
- Charging process charger or battery heating phenomenon (below 600C) is normal.
- When the electric baby carriage is not in use for a long time, it must be recharged at least once a month.
Battery instruction for Remote Control
-
When installing the battery, first open the battery cover, then install the battery according to the polanty, lock the battery cover. In the same way, take out the battery.
-
The remote control uses 2 # 7 batteries.
-
The non-rechargeable battery can not be charged.
-
Rechargeable batteries can only be charged under adult supervision.
-
The rechargeable battery should be removed from the toy before recharging.
-
Different types of batteries or old and new batteries should not be mixed.
-
Batteries should be placed at the correct polarity.
-
The depleted battery should be removed from the toy.
-
The power terminal must not be short-circuited.
Trouble shooting
Fault type | Detection site | Method of elimination |
---|
The Motor won’t run
th| 1.Is the foot switch in good contact?
2.Is the welding wire on the motor terminal in good condition?
3.Is the connector of the motor lead plugged in well?
4.Will the motor plug-in disconnect, directly, connected to the battery
rotation?| No, fix the foot switch; yes, next. No, weld the terminals to the
wire; yes, next. No, plug the connector in; yes, next. Do not turn, change the
motor; turn, Drive Circuit Board failure, send professional repair point
repair.
To go only forward without going back, or fo go only backward without
goingforward| 1.Detect reverse switch, with a three meter
test good contact?
2.Drive line to reverse switch wiring, is it good?| No, change the reversing
switch; yes, next No, the line connected;
yes, Drive Circuit Board failure, send professional repair point repair.
Ifs slow| 1.Check if the BATTERY VOLTAGE IS ABOVE 12V?
2.Will the motor (with gearbox) directly
connected to the battery, speed up or not? a Unload the gear box, check the
gear
rotation, move well or not?| No, charge.-yes, next. No, next item; yes, Drive
Circuit Board failure, send professional repair point repair.
No, change the gear box;
yes, change the motor.
Its not charging| 1.Does the charger output terminal have 12V voltage?
2.Will charger input, output plug good, will the battery end two plug springs
pull out, test has 12V voltage?
3.Check that the charging seat fastener is loose and the solder joint is
free?| No, change the charger; yes, next. Yes, change the battery.
No, next
Yeah, plug in the charger.
Instructions for use
Remote control functions and instructions
- Do not switch the forward and backward buttons during vehicle movement to avoid damaging the gearbox and motor.
- The remote control needs a battery to work properly.
- The remote control requires the use of a guardian.
- Remote control is preferred.
Cade alignment method:
Press and hold the code key, the indicator flashes, turn on the power of the
stroller, and the code is successfully matched
Precautions for use
- Not in the streets, roads, slopes and other hazardous areas.
- Please be on a well-Jevel ground, please do not use on the smooth surface (such as marble, floor tiles} and other surfaces.
- This product limited by one person, can nol be overloaded, the maximum load 25KG.
- Children must ride under adult guidance and caretakers must not leave during cycling.
- Do not modify ihe vehicle wiring or additional charging device.
- Do not use in water, do not pour water and other liquids in the car.
- The car should not be blocked in the process of moving the car, so as to avoid damage to the device, such as blocked phenomenon, please immediately release Foot switch, remove the obstacles before riding,
- The car should be timely charging slow cycling speed, cycling for too long will cause shortened battery life.
- Do not use, please tum off the power switch, unplug the battery connector when not in use for a long time.
- Do not drive in rainy weather,
- The main use of PP car material, non-toxic, non-radiation, safe lo use for a period of three years.
Packing Instruction
- Product specification 1
- Car body 1
- The saddle 1
- Theremote control 1
- The charger 1
- Accessories package 1
- The front wheel 2
- The rear wheel 2
- Thesteeringwheel 1
- Wheel cover 4
Schematic
Instructions
-
Install the tires
Start with the front and rear wheels.Fix the gasket, front wheel, gasket in turn, and then fix it with nuts. Fix the rear wheel, gasket in turn, and then fix with nuts. And install the front and rear wheels on the other side in the same way. -
Install the steering wheel Connect the steering wheel to the body wire, turn the steering wheel to the steering lever, Use a screw nut to fix
-
Install the front guard plate The corresponding bayonet is stuck and fixed with a screw.
-
Connect power The positive and negative wires can be connected
-
Install rear backrest Clamp the backrest into the corresponding position and fix it with two screws.
-
Install the rear tail
Put the tail in position
Clamp in and fix with two screws.
Instructions for use
-
RF warning for Portable device:
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction
WARNING: Any changes or modifica tions not expressly approved by the party responsible for compli ance could void the user’s autho rity to operate this equipment.
Remote control functions and instructions- Do not switch the forward and backward butions during vehicle movement to avoid damaging the gearbox and motor.
- The remote control needs a battery to work property.
- The remote control requires the use of a guardian.
- Remote corirot is preferred.
Code alignment method: Press and hold the code key, the indicator flashes, tum on the power of the stroller, and the code is successfully matched
FCC Statement
WARNING: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this
equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
The device must not be co-located or operating in conjunction with any other
antenna or transmitter.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>