SUNCO LIGHTING 50W-40W-30W LED Ceiling Panel Light Instruction Manual

SUNCO LIGHTING 50W-40W-30W LED Ceiling Panel Light

INSTALL INSTRUCTIONS

PLEASE FIND A QUALIFIED ELECTRICIAN FOR INSTALLATION. Please read the instructions before you install and use the luminaire. WARNING, CAUTIONS AND OPERATING INSTRUCTIONS

• Make all electrical and grounded connections by the National Electrical Code and any applicable local code requirements.
• To reduce the risk of death, personal injury, or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards read all warnings and instructions included with and on the fixture box and all fixture labels.
• Before installing, servicing, or performing routine maintenance on this equipment, follow these general precautions.
• Commercial installation, service, and maintenance of luminaires should be performed by a qualified licensed electrician.
• For the installation: If you are unsure about the installation or maintenance of the luminaires, consult a qualified licensed electrician and check your local electrical code.
• To prevent wiring damage or abrasion, do not expose wiring to the edges of sheet metal or other sharp objects.
• Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.

WARNING: RISK OF FIRE OR ELECTRICAL SHOCK

• Turn off electrical power at the fuse or circuit breaker box before wiring the fixture to the power supply.
• Turn off the power when you perform any maintenance.
• Verify that the supply voltage is correct by comparing it with the luminaire label information.
• All wiring connections should be capped with UL-approved wire connectors.

CAUTION: RISK OF INJURY

• Avoid direct eye exposure to the un-louvered light source while it is on.
• Account for small parts and destroy packing material, as these may be hazardous to children.
• Risk of burn. Discounts ect power and allow the fixture to cool before changing the bulb or handling the fixture.
• Do not relocate the Green ground screw provided, it is in the proper location.
• Minimum 194°F supply connectors.
• Suitable for Dry or Damp locations, Type IC

WARNING – TURN OFF THE POWER SUPPLY FROM THE MAIN CIRCUIT BREAKER BEFORE INSTALLING OR SERVICING.

RECESSED MOUNTING

1. Carefully unpack the unit and properly inspect for defects before installing. Wear work gloves to prevent dirt and oil from being transferred to the luminaire. If cleaning is needed, use gloves and a dry cloth. It is not recommended to use hazardous chemicals. (Fig. 1)

2. Lift the four mounting clips on the sides of the luminaire. If done by hand, use gloves, or use pliers (Fig. 2).

3. Insert luminaire into a T-bar ceiling grid. Secure safety cable to connection hole as needed to meet local seismic requirements. Safety cable and method of attachment to the building provided by the contractor according to local building codes. (Fig. 3)
   WARNING – TURN OFF THE POWER SUPPLY FROM THE MAIN CIRCUIT BREAKER BEFORE INSTALLING OR SERVICING.
   RECESSED MOUNTING (Cont’d)

4. Remove electrical enclosure cover. Carefully remove the knockout for AC line input wires (and 0-10V control line if needed). Install UL-listed electrical fittings in the knockout holes for wire protection if needed. (Fig. 4)

5. Plug in the AC line (L, N, and GND) to the LED Driver using 18-14AWG Wire. When connecting the 0-10V dimming controller, wires must run through a separate knockout hole equipped with an appropriate electrical fitting. (Fig. 5)

6. Follow wire connection instructions (Fig. 6). When using the 0-10V dimming controller, run wires from the controller through a different knockout than the AC input wire. Do not forget to return the electrical enclosure cover and tighten the screws.

SPEC-SELECT™ FIXTURES – FIELD ADJUSTABLE WATTAGE & CCT (If applicable)
The end users may adjust the color temperature and lumen output, respectively, by the two slide switches integrated into the driver. Each switch has 3 options (left, middle, and right), and each position corresponds to 3 color temperatures (3500K, 4100K, and 5000K) and 3 wattages, which can be adjusted to the desired combination.

1. Switches are located on the driver. (Fig. 7)
2. Select a wattage and color temperature by sliding the switch left or right respectively to the desired value.

WARNING – TURN OFF THE POWER SUPPLY FROM THE MAIN CIRCUIT BREAKER BEFORE INSTALLING

CABLE SUSPENDED MOUNTING (Kit Sold Separately)

1.  Secure the round ceiling plate into the ceiling by using the expansion anchor and self-tapping screws. Confirm Cable A is fully pulled through and secure in the round ceiling plate. (Fig. 8)
2. Insert the end of Cable A into the cable gripper that is pre-attached to Cable B. Then adjust Cable A to the desired height and adjust Cable B to the desired angle. (Fig. 8)
3. Bend out earthquake brackets. Using the carabineers, connect Cable B to the large hole in the earthquake bracket and make final adjustments. (Fig. 9)
4. Connect the LED driver to the AC main power. (Fig. 6)

SURFACE MOUNTING (Kit Sold Separately)

1. Assemble the mounting frame with the screws and the connection plate (Fig. 10).
2. Mount the frame on the ceiling with screws. Make sure that the wire is long enough for Step 4 below. (Fig. 11).
3. After mounting the frame on the ceiling, remove one side of the mounting frame (Fig. 12).
4. Connect the wires from the main to the LED driver, then slide the LED panel into the frame (Fig. 13).
5. Replace the side of the frame (Fig. 14).

Specifications are subject to change without notice. Photos and line drawings may not be to scale and are for general reference only.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>