e-BABETA RACCeWAY Electro Scooter User Manual

e-BABETA RACCeWAY Electro Scooter

The instructional video can be found at:www.youtube.com/embed/G7NulwAhp7w.

IMPORTANT NOTICE

Before you start assembly:

• Inspect the shipping container for significant damage. Then remove all packing material and components from the box.
• Before mounting, make sure that the main circuit breaker is off.

Estimated time required for installation:

• Allow at least 30 minutes for installation.
• 6-1 O hours should be enough to charge the battery (in no case should it recharge more than 14 hours).

Assembly tools (not included):

MAIN COMPONENTS OF THE ELECTRIC SCOOTER

INSTALLATION INSTRUCTIONS

Each electric scooter was carefully assembled and inspected before leaving the factory. You have to install the pedals and rearview mirrors. Follow the installation instructions. Tools Required: Key; hex key; screwdriver, etc. Each package includes a set of installation tools.

INSTALLING THE HANDLEBAR
Installation tools: Wrench No.12

1. Place the handlebar module on the steering column.
2. Connect the handlebar module to the steering column using a bolt with a front cover.
3. Insert the bolt so that the groove in the bolt is vertically aligned with the handlebar axis.
4. Place the front cover from the front of the steering column.
5. Screw the bolt into the cap and tighten properly.
6. Resulting state.

INSTALLING THE FRONT FENDER
Installation tools: Wrench No. 8, Phillips screwdriver

1. Insert the mudguard into the front fork and secure it with four nuts and bolts.
2. Place the mudguard between the forks.
3. Always insert the bolt from the outside and fasten it from the inside with the nut.
   Hold the nut with a wrench and tighten the bolt from the outside with a Phillips screwdriver.

INSTALLING THE FRONT WHEEL
Installation tools: Wrench No. 12 and 17.

1. The illustration shows the wheel with brake disc, wheel shaft, shorter and longer front wheel spacers, washer and nut.
2. Demonstration of correct positioning of front wheel shaft including correct positioning of two front wheel spacers of different lengths. When installing the spacers incorrectly, the wheel cannot be seated!
3. Insert the wheel with the brake disc on the left. Push the wheel shaft from the left side and make sure the spacers are correctly positioned (longer spacer on the left, shorter one on the right).
4. Install the washer and nut.
5. Tighten properly with a torque wrench. inflate the tyre to the tyre pressure specified by the tyre manufacturer.

INSTALLING THE BRAKE CALIPER

• Installation tools: Key No. 14
• When installing the calliper, the wheel must already be mounted.

1. Align the brake calliper to the left leg of the handlebar fork. (illustrative photo)
2. Attach the calliper to the fork with the bolts on which you first fit the fiat, then the spring and finally the fiat washer (illustrative photo)
3. The brake disc must be located between the brake pads.

INSTALLING THE FRONT STORAGE BOX
Installation tools: ratchet, extension, but no. 10, screwdriver.

1. Position the front storage box to the steering column.
2. Using the extension ratchet, secure the rear wall to the steering column with four screws.
3. Place the top cover on the steering column and tighten it with four screws using a Phillips screwdriver on the inside of the box.
4. Insert the tray into the box and tighten it to the box body with four screws.
5. The cable attached to the hinged part of the body box attaches to the body box by a screw.
6. Resulting state.

INSTALLING PEDALS
Installation tools: Wrench No. 15.

Warning:
Do not tighten by force, as the handles are made of aluminium alloy.

1. The right pedal (marked “R” on the pedal shaft) must be mounted on the crank on the right and tightened clockwise.
2. The left pedal (marked with the symbol “L”) is mounted on the crank on the left and tightened firmly counterclockwise.

MIRRORS INSTALLATION
Installation tools: Wrench No. 14

1. Screw the mirrors into the hole at the top of the handlebar.
2. After screwing in the mirrors, tighten the nut with the wrench.
3. Drag the free end of the rubber cap to cover the nut and align it with the handlebar.

Note:
Before driving, adjust the handlebars so that you have a

CHARGING THE BATTERY AND TURNING THE E-SCOOTER ON
There are two ways to charge the battery:

First charging method:

1. Lift the seat under which the battery is located.
2. Connect the power cord directly to the battery outlet.
3. Switch on the main circuit breaker.

Second charging method:
Remove the battery from the seat part, bring it to an electrical outlet and start charging.

Third charging method:

1. Into the charging socket, which is located from the outside under the seat above the rear fender. This external socket allows you to charge a locked motorcycle without unlocking or unfolding the seat. The condition is that the circuit breaker is on.

When standing for a long time, we recommend disconnecting the battery or turning off the circuit breaker. Our machine is equipped with an alarm with a remote start and it has a constant consumption. lt is therefore possible to discharge the batteries below the critical limit during long-term standing.

INSTRUMENT PANEL

HOLDER AND SUITCASE ASSEMBLY
The suitcase with the holder is not part of E-BABETA. They can be purchased as an additional assortment on the website www.motoe.eu.

1. Lift the seat and loosen the three self-tapping screws on the top of the plastic, above the silver Handle.
2. Remove the four screws from the silver handle and the two screws from the bottom of the seat above the turn signals and remove the original handle.
3. The housing contains a set of screws for mounting. ln the set you will find:
   • A) 4x 6 cm long screw with nut and large shaped washer (copper)
   • B) 4x 4 cm long screw (silver)
   • C) Fiat head screw 2x 2 cm (grey)
   • D) 2x profiled sheet metal
4. Attach screws “C” to the seat lock.
5. Attach the trunk holder and tighten the screws “B” from below and from above
6. Tighten the 3 self-tapping screws in the upper plastic and screw in the two screws from the lower part seats above the turn signal.
7. Remove the two rubber tabs on the lock side from the bottom of the seat.
8. Place the suitcase on the suitcase holder and screw it to the holder – from the inside, place the screw “A” using Use nuts on the washer and bottom. It is not necessary to use a washer for the profile sheets.

SAFETY WARNING

• Store batteries in a dry, warm environment.
• Keep the batteries charged at all times.
• If you park in an outdoor or cold environment, the battery must always be charged, otherwise it will be irreversibly damaged.
• If the scooter is not used for a long time, the battery will self-discharge, so it is recommended to check the battery condition continuously so that the voltage does not drop below the critical value when the battery can no longer be charged.
• Any claims concerning a battery damaged due to such improper treatment will not be accepted.

GENERAL INSTRUCTIONS

We would like to thank you for purchasing your electric scooter. You are now one step closer to a new mode of transport that is fast, fun and environmentally friendly. Your electric scooter is equipped with standard security features and a sound alarm system with remote control *. Please read this guide carefully before setting up on your first journey. each user of this product must be fully aware of the safety risks associated with the operation of this product on the road. We wish you a pleasant journey.

DESCRIPTION OF REMOTE CONTROL WITH ALARM

COMMENTS:

• In this manual, you will find basic information about your electric scooter, its safe operation and maintenance.
• This product is continually being improved and we would like to ask you to be lenient if you notice minor changes to this manual when you buy the product.
• We recommend that you do not modify any technical parameters of your electric scooter.
• WARNING: Read and follow the safety instructions in this manual. For your safety, never misuse, incorrectly in sta li or modify the main components and always remember the slogan “Safety first”! Warning: This product cannot be used for downhill races, stunts, ruthless driving or aggressive off-road driving.

WARRANTY

The warranty period of the machine is 24 months, and the warranty on the battery is 6 months.

CHARGING INSTRUCTIONS

• Use only the charger designed for this electric scooter (never use a charger from another model). Before charging, set the switch to the OFF position and remove the key. Use the charger in a dry and well-ventilated area.
• The charger is for indoor use only. Protect the charger from water to avoid short-circuiting. Do not use it in wet, flammable, or explosive environments. Do not remove the plug by pulling the cord, always grasp the charging port by the metal body.
• First, plug the charger’s output plug securely into the battery receptacle, and then insert the input plug into a power outlet. The charger indicator lights up to indicate that charging is in progress.
• When the light changes from red to green, it indicates that the battery is fully charged. Typically, it will take approximately 6-1 O hour for the battery to fully charge. lf you have time, it is recommended to charge it for 2 more hours after the indicator light turns green. (This will positively affect battery life).
• When the green light is on, the charger is in a maintenance charging state. lf you are away for a long time, you should remove the charger plug, especially in hot weather.
• The charger heats up during charging, so keep it away from heat. Always keep the charger dry and clean. The electronics inside are under high voltage, so never disassemble it yourself.
• After charging, first, unplug the power plug and then remove the output connector from the battery. Do not leave the charger plugged into a battery or wall outlet for an extended period as this may damage the charger and cause a fire.
• Keep the charger out of the reach of children while charging. Do not place anything on the charger or allow any liquid to come into contact with the charger.
• The first 10-15 charges are unstable, the charging time can be up to 12 hours, and the charge indicator on the scooter display can show a partially discharged battery. After formatting the battery, everything will be fine
• Furthermore, the battery is protected by its fuse 30A, which is stored from the side of the plastic battery pack and secured with a plastic screw cap.

CHARGER

Has three charging options:

1. Remove the battery from the under-seat part, bring it to the electrical outlet and start charging
2. Disconnect the battery in the under-seat part from the power connector, connect the charger and charge
3. The e-scooter has, above the rear wheel in the fixed part of the mudguard, a connector for connecting the charger.

The charger has 2 diodes. The first (red) lights up when the charger is plugged in, while the second signals charging. When the charger is connected, the first red light comes on immediately and the second one lights up green, then red when everything is OK. it will glow green again when fully charged.

SAFE DRIVING

• Follow the Road Traffic Regulations. Do not transport other persons on this electric scooter.
• Read this manual carefully and make sure you fully understand it and that you can drive the electric scooter before heading out on the road.
• Do not lend the electric scooter to anyone unfamiliar with how to operate it .
• Check regularly that the battery is properly charged.
• Check the condition of the brakes before each journey. lf necessary, adjust them carefully to make sure they work properly. Brake early and always reduce your travel speed when it rains or snows
• Always hold the handlebar with both hands.
• Drive in such a way that no limbs or other objects come into contact with the chain or wheels
• Do not touch the battery charging connector with a wet hand, wrench, or other metal object, as this will damage the battery pole and cause a short circuit .
• Wear bright colours when driving at night to be visible to drivers of other motor vehicles.
• Only one person can drive this electric scooter, 2 for a short time, but the maximum load of 125kg
• Do not drive under the influence of addictive substances, alcohol or medication that could affect your ability to operate a motor vehicle .
• Do not drive in poor conditions, such as uneven, wet or unpaved surfaces.
• If possible, do not drive in poor weather conditions, poor visibility or if you are very tired.
• This electric scooter can be operated in rainy weather, but its control unit, motor or other electrical devices must not be submerged in water. This could cause a short circuit and could result in an accident
• Never use spray water to wash your electric scooter to avoid its electrical components getting wet (battery connector, motor, control unit, cables, handlebar controls, etc.)
• This electric scooter must not be driven by persons under 15 years of age.

DRIVING DIRECTIONS

Check before driving for the first time:

• Before leaving the factory, a scooter exit check was performed – but check the following before driving for the first time:
• First, make sure the battery is fully charged and correctly positioned
• Check the front and rear brakes and make sure they work properly
• Check the tyres and make sure they are well-inflated
• Check that the front and rear wheels are properly secured
• Check the pedals to make sure they are properly secured and that all lock nuts and bolts are tightened properly

Driving:
First, turn the ignition key to the “ON” position. You will see the battery charge level on the battery status indicator.

Pointer location:

• [H]: The battery is sufficiently charged
• [L]: The battery is not charged enough

The position of the pointer in the red box indicates that the battery is low and needs to be recharged.

You can then easily start the electric scooter by turning the throttle handle (anti-clockwise). Accelerate gradually, do not attempt to reach maximum speed immediately, which would overload electrical components and battery. Gradual acceleration saves both the battery and the engine. The brake has the function of cutting off the power supply. lf one of the brakes is pressed, the power supply is automatically cut off and the motor is switched off. Using the parking brake or releasing the throttle automatically cuts off the power to the engine. However, you should avoid attempting to use the throttle at the same time as braking to avoid overloading the engine. The electric scooter control unit is equipped with overvoltage protection. lf the battery is running low and you are going uphill or against a strong wind, the surge protector will limit the speed. lf you can use the pedal I s in such a situation, this will help the electrical system function properly. This electric scooter is also equipped with low-voltage protection. lf the battery is running low and the accelerator pedal is still used, the battery may be seriously damaged. Therefore, in this case, the power supply is automatically cut off.

Attention:
If the ignition key is in the “ON” position and the driver moves the throttle handle, the e­scooter will move! Do not put the key in the ON position until you are ready to go. After starting, accelerate slowly and smoothly and do not attempt to reach maximum speed quickly, otherwise electrical components may be damaged. lf you push the e-scooter, turn off the power supply to avoid accidentally moving the throttle handle and causing the e-scooter to move unexpectedly, which could cause an accident. Use the brakes wisely and only when necessary.

Battery Level Meter:
If the battery level decreases and the indicator goes to [L]. you should turn off the battery and fully charge the battery as soon as possible.

Notes:
Do not expose the electric scooter to sunlight or rain for long periods, as this could negatively affect the operation of some electrical components.

Special note:
If you frequently use the brakes if you start and stop the engine frequently, if you are driving upwind or uphill, or if you exceed the permissible weight of the load, this will affect battery performance and range. lf you want to positively influence the range, follow the steps:

• Turn the throttle handle continuously to increase the speed gradually
• Do not brake too often -only when necessary.
• If possible, do not start or turn off the electric scooter too often.
• If you want to start, it is always best to do this only after moving the electric scooter a bit

MAINTENANCE

ATTENTION:
To carry out maintenance, first, switch off the electric scooter and remove the ignition key.

Regular check:
Regularly check the condition of your electric scooter and make regular checks for proper tyre inflation, check the sensitivity of the brakes, tighten all components, and make sure they do not make any unusual noise or abnormal noise when driving.

Brake adjustment:

• Proper adjustment of the brakes will promote the correct operation of the warning lights and increase driver safety:
• The brakes are adjusted similarly to each normal I wheel. It is important that the brakes work properly and that the electrical disconnect devices are in working order (cable to the brake levers). There is a micro-adjustable rear drum brake nut that allows you to very easily adjust the response of the brakes to the push.
• Once the brakes are set, turn the wheels to see if there is any chafing. Also make sure that if any of the brakes are pressed, the power cut function will be activated and the motor will stop.

Lubrication:

• To ensure the long life of your electric scooter, the following components should be regularly lubricated every 6 months:
• Front axle; cha in; rear axle; the idle, front fork and other moving parts must be lubricated only with grease and the brake must not be filled with grease at all.
• Electrical components do not need to be specially cleaned as they have been lubricated at the factory. lf any defect is found, contact an authorized service centre.

Cleaning:

• The electric scooter should be cleaned with a damp sponge, but care should be taken to avoid electrical parts coming into contact with water (battery connection, engine (rear axle), electrical cables, handlebar controls, etc.). Dry with a cloth.
• Do not use a strong stream of water when cleaning the electric scooter. Use a cloth to avoid short-circuiting electrical components. Your electric scooter is durable and does not require waxing. lf necessary, clean with a mild detergent and rinse aid to restore its original shine.

TROUBLESHOOTING

Sean the QR code for other language versions:

Technical support:

• Pavel Koželuh
• tel.: + 420 777 737 360 (Mo-Fri 7:00 – 15:30)
• e-mail: pavel.kozeluh@rulyt.cz

Service:

• tel.: + 420 777 736 214 (Mo-Fri 7:00 – 15:00)

• e-mail: reklamace@rulyt.cz
  Rulyt s.r.o., 5. května 435, 44001 Dobroměřice

• For more information:www.motoe.eu.

COMPLETE VEHICLE EU CERTIFICATE OF CONFORMITY

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>