OJF VS30F Vacuum Sealer Instruction Manual

VACUUM SEALER
OPERATING MANUAL
MODEL VS3OF

In order to make you better and safer to use this prod-uct. please Read the instructions carefully before you use it and keep it for the future use.

SAFETY GUIDANCE

In order to make you better and safer to use this product, please Read the instructions carefully before you use it and keep it for the future use.

1. Before turning on the power. please check whether the local power supply voltage is consistent with the voltage indicated on this appliance.

2. Do not use damaged power cords or plugs to operate this product after the product has broken down or has been damaged.
   If the power cord or this product is damaged, it must be returned to the authorized Aftermarket Service Centre.

3. To disconnect the power supply. unplug the power line plug from the power socket. Never pull the power cord when disconnecting the power supply.

4. If the power cord is damaged, in order to avoid danger, the power cord must be replaced by the manufacturer, or by a qualified agent, such as service agent

5. Never use an extended power cord on this product.

6. When you do not use this product or need cleaning, unplug the power cord from the power line socket first.

7. Do not use this product on wet or hot surfaces or on power supplies.

8. Do not place any spare parts. power cord or power plug of the product in water or other liquid.

9. Use only accessories or accessories recommended by the manufacturer.

10. This product can only be used for its specific purpose. only in indoor use.

11. When using this product, please closely supervise children. do not use this product as a toy.

12. For keep unit safety. the time interval between two sealings should not be less than 40 seconds.

INTRODUCTION SPARE PARTS OF VACUUM SEALER

1. Mode setting button : this button has two set modes (normal mode gentle mode) The default mode is the standard mode the corresponding standard indicator light is on and then press this button switch to gentle mode and the corresponding soft indicator light is on The normal mode is used for general food, soft mode is adopted for sealing the fragile food (Note: if the power is interrupted this setting will return to the default standard mode)
2. Food setting button: this button has two settings (dry mode, moist mode). The default mode is dry mode, the corresponding indicator light is on, and then press this button switch to wet mode and the corresponding indicator light is on The dry mode is used for dry food and wet mode is used for sealing the wet food.
3. Seal button: press this button to seal the plastic bag separately (the time interval between two sealing should not be less than 40 seconds).
4. Vacuum sealing button: press this button to vacuum the fresh-keeping bag then seal automatically If you need to manually control the vacuum you can press the sealing button at any time to seal the food (the time interval between two sealing should not be less than 40 seconds)
5. Stop button: Press this button during the working process and stop working immediately
6. Lock catch: with both hands under pressure and lock on the cover hear the clicking and make sure it is locked with each other then can start sealing or vacuum sealing
7. High temperature adhesive tape: make the heating wire distribute more evenly.
8. Sealing tape: With the High-temp adhesive, to make sealing more smooth
9. Sealed area: when vacuuming, the plastic bag opening side must be put into this area. After the upper cover and the base are buckled, two airtight sponge rings are pressed together to form a sealed space.
10. Release button: after the vacuum sealing is finished, press the release button on both sides to deflate the machine and open the top cover. Remove the sealed food.
11. Vacuum hole: when the external vacuum box or other parts are pumped, the outer joint is inserted into the air hole. When the vacuum seal is used, do not block the hole.
12. External vacuum button: press this button, the machine begin to vacuum containers or other parts of the vacuum treatment, until complete.
13. Sealed ring: both one up and down, airtight strong, blocking the flow of sealed spaces with the outside air, to ensure vacuum pumping, sealing chamber to

OPERATION PROCESS OF VACUUM SEALER

1. open the outer packing and place the vacuum sealer on a dry flat place to ensure adequate operating space around the machine

2. vacuum package selection tips:
   (1) the width ≤ 11.8 in with vacuum bag lines are applicable to this product
   (2) the vacuum sealer matches the original full width microporous vacuum bag, and the original bag is the best. Customers can also choose another vacuum bag.
   

3. vacuum sealing steps
   (1) Put the food into a plastic bag which one side sealed already Note: the vacuum bag opening side should not be less than 1.97 in space
   

OPERATION PROCESS OF VACUUM SEALER

(2) open the top cover, put the bag in the middle of the sealing area.
Note: The opening side of bag must touch the two vertical parts

(3) Close the top cover, press the two sides of the cover respectively until hearing ‘clicking” sound,to make the cover locked with the base.
(4) Press the vacuum sealing button to start working, and when the vacuum reaches the requirement, then start the sealing automatically.

OPERATION PROCESS OF VACUUM SEALER

(5) when the sealing has finished the lamp off, press the release button on both sides to open the cover.
(6) check the sealing place, sealing line must be uniform width, continuous smooth, no wrinkles: check whether the vacuum baa is damaged and leak.
Note: small, fragile objects (such as biscuits, bread, etc.) not recommended to use this machine

VACUUM SEALER SPECIFICATIONS

Voltage AC 120V -60Hz Working model Full automatic /manual Vacuum degree -60kpa Max Sealing width 11.8 in Sealing thickness 0.12 in Product size 13.2 x 7.48 x 3.94 in Net weight 2.65 lbs

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>