F-NIRSi DSO153 Mini Oscilloscope and Signal Generator Instruction Manual

June 1, 2024
F-NIRSi

DSO153
Digital Oscilloscope Instruction Manual

DSO153 Mini Oscilloscope and Signal Generator

Notice to users

  • This manual provides detailed introductions to the product. Please read this manual carefully ensure obtain the best state of the product.
  • Please keep this manual properly .
  • Do not use the instrument in flammable and explosive environments.
  • Waste batteries and instruments cannot be disposed of together with household waste. Please dispose of them in accordance with relevant national or local laws and regulations.
  • If there are any quality issues with the device or if you have any questions about using the device, please contact “FNIRSI” online customer service and we will solve it for you in the first time.

Product Introduction

DSO-153 is a highly practical and cost-effective handheld oscilloscope launched by our company, targeting the maintenance industry and development education industry. This oscilloscope has a real-time sampling rate of 5MS/s, 1MHz bandwidth, and complete triggering function (single, normal, auto). It can be used freely for both periodic analog signals and non periodic digital signals, and can measure up to ± 400V voltage with an efficient one click AUTO, which can display the measured waveform without complicated adjustments. In addition, it also comes with multiple functions signal generator (10KHz). Equipped with a 2.8-inch 320 * 240 resolution HD LCD screen and a built-in 1000mAh high- quality lithium battery, it can be used for about 4 hours when fully charged.

Panel Introduction

FNIRSi DSO 153 Mini Oscilloscope and Signal Generator - Panel
Introduction

Buttons Functions

Button| Operation| Main menu| Oscilloscope| Signal generator| Setting
---|---|---|---|---|---
| Short press| Select Up| Control the function
adjusting of various
parameters| Not enter value settings: waveform select| Setting select
Enter value settings:
value bit select
| press Short| Enter menu| 50%| enter/exit values| enter/exit values settings inthe sound  and light values. In restoring factory settings, restore.
Long press| Return to main menu
| Short press| Select down| Control the function
adjusting of various
parameters| Not enter value
Settings:
waveform select| Setting select

Enter value settings:
value bit select
Button| Operation| Man menu| Oscilloscope| Signal generator| Setting
---|---|---|---|---|---

AUTO

| Short press| /| Auto measurement| /| /
Long press| /

MODE

| Short press| /| Auto/Single /Normal switch| /| /
Long press| /| Rising and falling edges switch| /| /
| Short press| /| parameter adjustment
| Short press| /

RUN

| Short press| /| Run/Pause waveform Display/disable| Turn on/off output| /
Long press| measurement parameters| /
| Short press| Power off
Long press| Power on

Product Parameters

Sampling rate 5MS/s
Bandwidth 1M
Vertical sensitivity 10mV/Div-10V/Div
Time Base Range 500ns-20S
Voltage range X1:±40V(Vpp:80V)

X10:±400V(Vpp:800V)
Trigger Mode| Automatic/Normal/Single
Trigger Edge| Rising edge /falling edge
Coupling| AC/DC
Square wave calibration| Frequency: 1K; Duty cycle: 50%; Amplitude: 3.3V

※The size and weight are both manually measured, with slight errors, please refer to the actual product for accuracy.

Signal generator

Frequency| 0-10KHz
Duty cycle| 0-100% (rectangular and sawtooth waves)
Amplitude| 0.1-3.3V
Waveforms| Sine wave, rectangular wave, sawtooth wave, half wave, full wave, step wave, anti step wave, noise wave, exponential rise, exponential drop, DC signal, multi tone, Sink pulse, Lorentz wave.
Others

Display| 2.8 inches/PPI:320*240
USB charging| 5V/1A
Lithium
battery capacity| 1000mAh
Size| 99×68.3×19.5mm
Weight| 100g

Screen Indication

FNIRSi DSO 153 Mini Oscilloscope and Signal Generator -Screen
Indication

  1. Vertical unit: represents the voltage represented by a large grid in the vertical direction

  2. Probe ratio: This must be consistent with the setting of the 1X/10X switch on the probe handle. If the probe is in 1X mode, then the oscilloscope should also be set to 1X mode, where 1X measures 40V voltage and 10X measures 400V voltage

  3. Horizontal time base, representing the length of time represented by a large grid in the horizontal direction

  4. Input coupling method indicator icon, AC represents AC coupling, DC represents DC coupling

  5. Trigger voltage indicator icon

  6. Trigger position indicator icon

  7. Baseline indicator icon, this icon indicates the current position as 0V voltage

  8. Run pause indicator icon, RUN represents run, STOP represents pause

  9. Trigger mode indicator icon, Auto represents automatic triggering, Single represents single triggering, Normal represents normal triggering

  10. Trigger edge indicator icon

  11. Signal generator on/off indicator icon

  12. Battery level

  13. Waveforms selection

  14. Display of waveforms

  15. Frequency setting

  16. Duty cycle setting

  17. Amplitude setting

  18. Opening and closing of signal generator (graying out when closed)

  19. Battery level

FNIRSi DSO 153 Mini Oscilloscope and Signal Generator - Settings
interface

  1. Set single item selection:
    Language, sound and light settings, startup, theme settings, automatic Shutdown, About, Restore Factory Settings

  2.  Specific settings details:
    ①Language: Chinese, English, Russian ,Japanese, Spanish,Portuguese, German, Korean.
    ②Sound and light settings: Brightness: 25-100; Sound: 0-10.
    ③Start up: turn off, oscilloscope, signal generator. This setting is used to set which function mode will be automatically started upon startup.
    ④Theme settings: blue, yellow.
    ⑤Automatic shutdown: off, 15 minutes, 30 minutes, 1 hour.
    ⑥About: Brand information, version number
    ⑦Restore factory settings.

Firmware Update

  1. In the case of shutting down, press and hold the first and then press power button.
  2. Use a Type-C cable to connect the Type-C port on the board to the computer, and a USB drive named “IAP” will pop up on the computer.
  3.  Pull the firmware into the USB drive, and if the firmware upgrade is completed, it will automatically jump to the APP.

Notice

  • Firmware upgrade only supports use on computer Windows 10 and above systems.
  • During the upgrade process, you need to keep pressing the power button until the file transfer is complete.

Points for Attention

  • After receiving the device, please use it when fully charged.
  • When using oscilloscope, pay attention to the selection of gear, and the gear of the oscilloscope should be consistent with the gear of the probe.
  • When measuring high voltage, do not touch any metal parts of the oscilloscope to avoid the risk of electric shock.
  • Try not to conduct a high-voltage test during charging.
  • When calibrating, it is necessary to unplug the BNC probe or short circuit the positive and negative terminals of the probe.
  • USB firmware upgrade only supports WIN10 and above. It is prohibited to drag files other than the released firmware, otherwise it may cause irreparable consequences.
  • Please charge using the voltage within the specifications in the instruction manual.

Contact Us

Any FNIRSI’s users with any questions who comes to contact us will have our promise to get a satisfactory solution +an extra 6 months warranty to thanks for your support!
By the way, we have created an interesting community, welcome to contact FNIRSI staff to join our community.
Shenzhen FNIRSI Technology Co., LTD.
Add.: West of Building C,Weida Industrial Park,Dalang Street,Longhua District,Shenzhen,Guangdong
E-mail: fnirsiofficial@gmail.com (Business)/ fnirsioffcialcs@gmail.com (Equipment service)
Tel: 0755-28020752 / +8613536884686
Web:www.fnirsi.cn

Download User manual&APP&Software
http://www.fnirsi.cn/
www.fnirsi.cn

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals