Vanstone Electronic Beijing Co Ltd Q161 QR Code Terminal User Guide
- June 1, 2024
- Vanstone Electronic Beijing Co Ltd
Table of Contents
Quick Start Guide
Q161 QR Code Terminal
The pictures and descriptions in this guide are for reference only, please refer to the physical objects
Operation Instructions:
一、 Power On/off
Power on: when the device is off, long press the power key until the screen
lights up;
Shutdown: When the device is powered on, long press the power key until the
screen turns off.
二、Function settings
1、Code scanning distribution network
- When the equipment is in standby mode, press 【F1】and 【4】to enter the code scanning distribution network mode;
- Turn on the mobile phone and connect it to the 2.4G band WIFI network. The WIFI connected to the mobile phone and the WIFI to be connected to the Q161 must be the same WIFI;
- Open WeChat on the mobile terminal to scan, scan the QR code of the distribution network at the bottom of Q161 with the mobile phone, and enter the configuration interface;
- Click “Configuration” on the mobile interface;
- Input the password of the WIFI to be connected to Q161 on the mobile phone, click the “Connect” button and wait for the WIFI configuration to succeed. If WIFI does not have a password, it is not necessary to enter the password, and directly click the “Connect” button to wait for the success of WIFI distribution network;
- Note: The distribution network should be completed within 150 seconds, otherwise the equipment will exit the distribution network mode, and the Q161 can only connect to the WIFI network in the 2.4G band.
2、Switch network
1）Press 【F1】 and 【5】 in the standby interface to switch between 4G network and WiFi network.
3、Press up and down keys in standby interface to adjust the volume
The merchant presses the up button to increase the volume gradually (up arrow) according to actual needs.
The merchant presses the down button to gradually decrease the volume (down arrow) according to actual needs.
三、Payment operation
1、Merchant passive collection
（1）Consumers use their mobile phones to scan the merchant’s QR code for collection, and enter the consumption amount on their mobile phones to make payment.
（2）Payment completed.
2、Merchant active collection
（1）The merchant uses the keyboard to input the consumption amount, and the main display screen displays the input amount.
（2）Consumers can choose the following three payment methods
1、Use the QR code automatically generated on the mobile phone scanning device screen to check the amount before making payment;
2、Use the NFC of the mobile phone to aim at the card reading area of the device to pay (only with non receiving version);
3、Use digital RMB to pay in the touch touch zone (only for the touch touch version);
（3）Payment completed.
matters needing attention
- It is recommended to use the power plug board with fuse, and the grounding is good;
- Do not damage the power cord and power adapter. If the power cord or power adapter is damaged, it can no longer be used;
- Please use the adapter with 3C certification and the original battery, and unplug the charging cable in time after fully charging;
- The equipment shall be placed on a stable platform indoors, and shall not be placed in a place with direct sunlight, high temperature, humidity or dust;
- Keep away from liquids;
- Do not insert any into any interface of the equipment, which may seriously damage the equipment;
- In case of equipment failure, please contact the special maintenance personnel, and the user shall not repair the equipment without authorization;
- No one is allowed to charge overnight.
- If consumers use power adapters for power supply, they should purchase matching power adapters that meet the requirements of corresponding safety standards or that have obtained CCC certification.
- Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion.Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas
FCC compliance statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two cond itions: (1) this device may not cause harmful
interference, and (2) this device must accept any int erference received,
including interference that may cause undesired operation.
changes or modifications not expressly approved by the party responsible for
compliance could v oid the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection a gainst harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that in terference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the inter ference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is co nnected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC SAR statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environ ment. End user must follow the specific operating
instructions for satisfying RF exposure complia nce. This transmitter must not
be colocated or operating in conjunction with any other antenna or
transmitter. The portable device is designed to meet the requirements for
exposure to radio waves establishe d by the Federal Communications Commission
(USA). These requirements set a SAR limit of 4.0 W/kg averaged over ten grams
of tissue. The highest SA R value reported under this standard during product
certification for use when properly worn on the limbs.
after-sale service
If you have any questions, please contact our resident service center or call
4001088166.
Product warranty card
Product name:___
Product model:__
Warranty terms:
- The company will provide you with quality after-sales service.
- If the user causes damage due to human factors, the company will charge maintenance fees when repairing.
- Please keep this card properly, and our company will take it as the warranty basis.
certificate
Examination clerk:__
Date:__
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>