PROWORLD MP354 Semi Auto Heat Press User Guide
- June 13, 2024
- PROWORLD
Table of Contents
PROWORLD MP354 Semi Auto Heat Press
Product Information
The product is a heat press machine used for transferring designs onto fabrics. It is manufactured by Pro World Inc. and can be purchased from their website at www.ProWorldInc.com. The machine is located at 961 Bethel Ave., Pennsauken, NJ 08110. For any inquiries or support, you can contact their toll-free number at 800-678-8289 or the international number at 856-406-1020. Fax inquiries can be sent to 856-406-1025.
Product Usage Instructions
Assemble The Control Box
- Take out the control box from the packaging carton and place it on top of the machine in the right position.
- Fasten the control box onto the machine using the provided screws.
- Connect the 5-phase aviation plug and 2-phase aviation plug securely.
Connecting the System
- Connect the power cord to a properly grounded electrical outlet with sufficient amperage rating.
- If an extension cord is used, it should be as short as possible and not less than 12 gauge. Heavy-duty cords are recommended.
- Do not use circuits with less than 15 amps or circuits that have other high-demand equipment or appliances plugged in.
The Ramspin System
- When the Ramspin System (Auto & Manual switch) is turned down, the machine will automatically open after work.
- Connect the power cord to a properly grounded electrical outlet with sufficient amperage rating.
Turn On The System
- Switch on the system using the power switch.
Adjusting The Temperature
- Press the SET button. The Set Temp lights located in the display will illuminate.
Adjusting The Time
- Once you have set the target temperature, press the SET button again. The Set Time lights located in the display will illuminate.
Counter Setting
- After adjusting the time, press the SET button again. The Counter lights located in the display will illuminate.
- If you want to set the counter, press the UP and DOWN arrows to adjust the counter within the range of 0-999.
- You can press the SET button to exit the counter setting if you do not want to set it.
Adjusting Pressure
- Locate the LED Display on the press and find the Pressure Adjustment Knob in the center of the heat platen.
- To adjust the pressure, turn the Pressure Adjustment Knob clockwise to increase the pressure or counter clockwise to decrease it.
- A visual Pressure Readout is located on the lower right side of the LCD Display. It will indicate the pressure level from 0 to 9, with 0 being no pressure and 9 being very heavy pressure.
OPERATION INSTRUCTIONS
Assemble The Control Box
- Take out control box inside of the packing carton, then put the control box on top of the machine in the right position must be replaced by the manufacturer, its service agent or a similarly qualified person in order to avoid hazard.
- Fasten the control box onto the machine with 4 screws tightly.
- Connect 5 phase aviation plug and 2 phase aviation plug,then fasten tightly.
ATTENTION: The aviation plug must be connected tightly.
CAUTION: A sway connector will cause aviation plug burning under heavy electricity.
Connecting the System
- Connect the power cord into a properly grounded electrical outlet with a sufficient amperage rating.
- VOLTAGE: 120 Volt – The GS-601 requires a full 20 amp grounded circuit for 120 volt operation. 240 Volt –The GS-601 requires a full 10 amp grounded circuit for 240 volt operation.
- EXTENSION CORDS If used, should be as short as possible and not less than 12 gauge. Heavy-duty cords are recommended.
- CIRCUITS that have less than 15 amps or that have other high demand equipment or appliances(especially more than one heat seal machine) plugged in, should not be used.
CAUTION: Failure to follow these instructions will cause:
- Erratic controller functions.
- Inaccurate displays & slow heat-up.
- The circuit breaker to disengage.
NOTE: If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or a similarly qualified person in order to avoid hazard.
The Ramspin System
- When the Ramspin System (Auto and manual switch) is turned down, the machine will automatically open after work.
- Connect the power cord into a properly grounded electrical outlet with a sufficient amperage rating.
Turn On The System
- Switch The System On
Adjusting The Temperature
- Press “SET” button .“Set Temp” lights located in the display will illuminate.
- Press “SET” button .“Set Temp” lights located in the display will illuminate.
- Next, press the UP and DOWN Arrow to increase or decrease the figure to set the Temperature.The temperature setting range is 170° F (76° C) to 430° F (220° C).
Adjusting The Time
- Once you have get your target Temp., press the “SET” button again. “Set Time” lights located in the display will illuminate.
Adjusting The Time
- Once you have get your target Temp., press the “SET” button again. “Set Time” lights located in the display will illuminate.
Counter Setting
- Once you have adjusted the time, press “SET” button again. “Counter” lights located in the display will illuminate indicating.
- You can press “SET” button to quit the setting if you do not want to set the Counter or you can press UP and DOWN Arrow to adjust the counter if needed. The counter setting range can be set from 0~999.
Adjusting Pressure
- First, locate the LED Display on the Press.The Pressure Adjustment Knob is located in the center of the heat platen.
- To adjust the Pressure, simply turn the Pressure Adjustment Knob to the right or clockwise to increase the Pressure and to the left or counter clockwise to decrease the Pressure. The readout will display the Pressure when locked down in the print position.
- A visual Pressure Readout is located on the lower right side of the LCD Display. When the handle is locked into the Print Position, a pressure number will be displayed. Readout will be on a scale of 0 – 9.A 0 Pressure readout would indicate no pressure at all and 9 would indicate very heavy pressure.
Printing & Pressing
- Once your equipment has reached the designated temperature;
- Position the garment and application and proceed to press;
- Lower and lock the heat platen into the press position. This procedure will start the automatic timing process;
- The timer will automatically count down and lift the heat platen into the “UP” position when the press cycle is complete;
NOTE: Please be aware after time is complete, gas shocks will automatically release the platen into the “UP” position.
Switching Between F/C
- Press the UP Arrow and “SET”button together and hold for 3 seconds to switch between Fahrenheit and Celsius. F/C indicator in display will show the result.
Temperature Calibration
- Press the DOWN Arrow and “SET” button together and hold for 3 seconds, “Calibrate” lights located in the display will illuminate indicating you are in the adjust temperature calibration mode.
- Press UP and Down Arrow to set correct temperature value. Press “SET” button to quit.
Auto Sleep Mode Setting
- Press “set” button for 4 seconds, display shows LCK.
- Input 68 then press “set” button to enter into second level menu.
- Press “set” button to select “SLP” mode below press up and down button to set auto sleep time.
- Press “set” button 4 seconds to quit.
NOTE
- Auto sleep setting unit is minute. Eg:1=1minute.
- Once auto sleep time is set,machine will enter into auto sleep mode if there is no operaton during the setting time.
- Press any button on the control board will activate machine from auto sleep mode.
Technical Parameters
Model: | MP354 & MP350-1515 |
---|---|
Heater Size: | 15’’ 15’’ (381 381mm) |
Pressure Display: | Yes |
Auto Open: | Yes |
Slide-out Lower Platen: | Yes |
Power(120volt) | 1800W/15Amps |
Power(240volt) | 1800W/8.2Amps |
Temperature Range: | Max.221 /430 |
Heating Up Time(180 ) | 20minutes |
--- | --- |
Time Range: | 0~999S |
Way To Change Lower Platen: | “Ramlock” quick change system |
Machine Size (open size): | 24.8 x16.1 x33.9 in |
Packing Size: | 29.1×18.9 x22.4 in |
Packing Weight: | 108.0lbs |
Certificate: | CE,FCC |
OPEN VIEW (GS-105HS)
OPEN VIEW (GS-105HS)
OPEN VIEW (GS-105HS)
OPEN VIEW (GS-105HS)
Technical Parameters
No. | Part Name(English) | Part No. | Qty. |
---|---|---|---|
1 | Display overlay | 1600549 | 1 |
2 | Control box top | 1200446 | 1 |
3 | Circuit breaker 18A | 1800349 | 1 |
4 | On/off switch | 1800346 | 1 |
5 | Emergency stop button | 1200579 | 1 |
6 | socket | 1800344 | 1 |
7 | Triac | 1800586 | 1 |
10 | Cooing sheet | 1300672 | 1 |
11 | Terminal Block | 1800345 | 1 |
12 | Circuit Board | 1800353 | 1 |
13 | Magnet switch | 1801814 | 1 |
14 | Magent | 1800609 | 1 |
15 | Control box base | 1200685 | 1 |
16 | 5 phase aviation plug (Female) with wires welded | 1800955 | 1 |
--- | --- | --- | --- |
17 | 2 phase aviation plug (Female) with wires welded | 1800962 | 1 |
18 | Machine handle | 1200581 | 2 |
Machine handle | J.03.05.0568 | 2 | |
19 | Machine arm | 1200583 | 2 |
Machine arm | 1200409 | 2 | |
20 | Washer 20-13-15 | 2000296 | 2 |
21 | Lift links | 1200140 | 2 |
Lift links | 1200139 | 2 | |
23 | Machine body | 1200582 | 2 |
Machine body | 1200397 | 2 | |
24 | Supporting block | 1200043 | 3 |
25 | Rubber foot | 1800317 | 4 |
26 | Machine foot | 1200649 | 2 |
--- | --- | --- | --- |
27 | Stud 10-72.5 GC1-21B | 1200051 | 1 |
28 | Bridle links | 1200138 | 2 |
Bridle links | 1200218 | 2 | |
29 | Lower platen holding base | 1200230 | 1 |
30 | Gas spring 270N | 1800054 | 2 |
Gas spring 350N | 1800055 | 2 | |
31 | Position block | 1200264 | 2 |
32 | Threaded Pin 13-164 | 1200050 | 1 |
33 | Threaded Pin 12-89 | 1200074 | 1 |
34 | Handle shaft | 1200145 | 1 |
35 | Foam Grip | 1300155 | 1 |
36 | Screw M8*16 | 1901071 | 1 |
37 | Adjustment spindle base | 1800142 | 1 |
39 | Adjustment spindle | 1800087 | 1 |
40 | Thermocouple | 1800281 | 1 |
42 | Balance screw | 1901074 | 1 |
43 | Thermosat | 1800133 | 1 |
44 | Lower platen | 1800802 | 1 |
Lower platen | 1800388 | 1 | |
45 | Adjustment knob | 1800479 | 1 |
46 | Silicon pad | 1800422 | 1 |
Silicon pad | 1200539 | 1 | |
47 | Platen holding block | 1200068 | 1 |
--- | --- | --- | --- |
Platen holding block | 1200042 | 1 | |
48 | Heat platen 15*15 | 1200287 | 1 |
Heat platen 16*20 | 1800386 | 1 | |
49 | Electromagnet 600N | 1200963 | 1 |
Electromagnet 800N | 1200981 | 1 | |
50 | Electromagnet holding sheet | 1200070 | 1 |
Electromagnet holding sheet | 1200067 | 1 | |
51 | Rubber foot | 1200605 | 1 |
52 | Holding sheet | J.03.05.0571 | 1 |
53 | Holding sheet screw | 1200659 | 1 |
55 | Heat platen cover 15*15 | 1200449 | 1 |
Heat platen cover 16*20 | 1200450 | 1 | |
56 | PP tube | 1800835 | 1 |
57 | 5 phase aviation plug(Male) with wires welded | 1800954 | 1 |
58 | Heating plate cover connecting plate 15*15 | J.03.05.0634 | 1 |
Heating plate cover connecting plate 16*20 | J.03.05.0633 | 1 | |
59 | Elastic glass bead screw M8 | J.03.06.0210 | 2 |
60 | Step bolt M6-8*12 | J.03.06.0092 | 2 |
61 | Cap nut M8 | J.03.06.0086 | 2 |
62 | Brace plate | J.03.05.0572 | 1 |
Sliding System
No. | Part Name(English) | Part No. | Qty. |
---|---|---|---|
1 | Cooper bush | 1200075 | 4 |
2 | Sliding Lower Platen Base | 1200425 | 1 |
Sliding Lower Platen Base | 1200426 | 1 | |
3 | Supporting Block | 1200197 | 1 |
Supporting Block | 1200052 | 1 | |
4 | Bearing block | 1200648 | 4 |
5 | Plated bar fixed board | 1200044 | 2 |
6 | Plated bar | 1200411 | 2 |
Plated bar | 1701037 | 2 | |
7 | O shape washer | 1200309 | 4 |
Ramlock System
No. | Part Name(English) | Part No. | Qty. |
---|---|---|---|
1 | Ramlock base | 1200958 | 1 |
2 | Ramlock locking sheet | 1200960 | 1 |
3 | Ramlock locking set(male) | 1200961 | 1 |
4 | Ramlock locking screw | 1900959 | 1 |
5 | Ramlock handle | 1200956 | 1 |
6 | Ramlock locking set(female) | 1200957 | 1 |
WIRING SCHEMATIC
TRANSPRO WARRANTY
Warranty Coverage
TransPro products offered by Pro World are warranted against defects in material and workmanship. Warranty is void if equipment has been damaged by accident, unreasonable use, neglect, unauthorized and/or improper service, or other causes not arising out of defects in material and workmanship. This warranty does not cover damage caused by normal wear and tear, neglect or lack of proper maintenance. This warranty is for the original purchaser/owner only, it is not transferable.
Warranty Duration
The heating element shall be warranted for the life of the heat press. There is a one (1) year warranty on major components, circuit boards and all other components.
Warranty Performance
During the warranty period, and in the event that a situation cannot be resolved by telephone/email and upon PRE-AUTHORIZATION from Pro World equipment must be shipped, freight prepaid to Pro World for service in the original packaging. After 30 days, all shipping and insurance expenses to and from Pro World of in-warranty equipment is solely the responsibility of the customer. Prior to 30 days the shipping costs will be refunded if Pro World deems the equipment to be defective as stated. Pro World cannot be held responsible for improper handling or any other damage incurred in transit. No charge will be made for labor and components for repair of in-warranty equipment. OUT-OF WARRANTY machines will be charged at the repair rates in effect at the time the machine is received.
Warranty Disclaimers
Pro World shall not be liable for loss of use of TransPro equipment or other incidental or consequential costs, expenses, or damages incurred by the original purchaser or any other user. The above warranty provisions constitute the entire agreement between all parties, and supersede any and all prior written and/or oral representations and understandings. This “Limited Warranty” applies to all TransPro equipment. However, the procedure for obtaining service may vary outside the continental United States. Contact your Pro World representative for warranty information. The purchaser is responsible for compliance with all local laws, regulations and measure. Agreement shall be governed by and construed in accordance with all applicable laws of said region.
Contact
Pro World Inc.
- 961 Bethel Ave. Pennsauken, NJ 08110
- Toll Free: 800-678-8289
- Outside U.S.: 856-406-1020
- Fax: 856-406-1025i
- www.ProWorldInc.com