BUTURE Beta01 Portable Car Jump Starter with Air Compressor User Manual
- June 14, 2024
- BUTURE
Table of Contents
BUTURE Beta01 Portable Car Jump Starter with Air Compressor
Packing list
Know Your Beta 1
Thanks for choosing BUTURE Beta01 jump starter! Please read all instructions carefully before using this product and keep these instructions for easy reference.
Specification
| Model | Beta01 |
|---|---|
| Capacity | 20000mAh |
| Input | 5V/2A |
| Outputs | 5V/2.4A*2 |
| Air Pressure | Max 150PSI |
| Operation Temp. | -20°C- 60°C |
Operation Guide
Before use, please note:
- Charger not included. A universal USB charger is fine, such as your phone charger (2A above is suggested) .
- When using the product for the first time, please make sure it is fully charged.
- It is recommended to charge up the product every 3 months to :_ prolong its lifespan even if the unit has not been used.
Recharge The Product
- Step 1. Connect the product to power supply via the charge cable .
- Step 2. Disconnect the power after it is fully charged.
Charge Other USB Devices
- Step 1. Connect the product to your iPhone , smart phone or other USB electronic devices via the charge cable.
- Step 2. Press the power button to start charging. Disconnect when charging is not required.
LED Emergency Light
Long press the LED Button for 3 seconds, the white flashlight will be on.
Short press to switch to Strobe and SOS mode in turn. Then press again to turn
it off.
Start Vehicles
Before use, please note
- This product is only suitable for 12 V vehicles
- Before starting your car, it’s best to make sure the product has enough power.
- Step 1. Insert the clamp plug completely into the product. The red and green indicators will flash alternately.
- Step 2. Connect the red clamp to the positive terminal ( +) of your vehicle battery and the black clamp to negative one(-). The green indicators will be solid.
- Step 3. Start your car. If the engine is not successfully started on the first try, disconnect it from the car battery, and wait for at least 30 seconds to try again.
- Step 4. When the vehicle is started, remove the jumper cable from your car battery within 30 seconds.
Inflate Tires
- Step 1. Connect the air hose firmly to the product and tire air valve respectively, and press down the handle to fix the air hose.
- Step 2. Short press the power button to activate the product, then press the pump button to switch to pumping mode (2.5Bar default). You can press the unit button to switch pressure unit between BAR, Kpa and PSI, and press the “+” and “-” button to adjust pressure values.
- Step 3. After the setting is completed, press the power button to start pumping, and the real-time tire air compressor will be displayed.
- Step 4. The product will automatically shut off when it has reached the pre-set pressure value.
Tip: If using for long period, It’s recommended to stop in every 10 minutes to cool down it. Otherwise the protection program will be started automatically
Indicator And Troubleshooting
In any of the following situations, the smart clamp will turn protections on:
Indicator Situations
- Flashing red and green indicator
- Jumper cable connected
- Solid green indicator
- Ready to start
- Solid red indicator
- Low voltage protection —Recharge the product
- Over-heating protection —Remove the clamps to let it cool
- Timeout protection —Connection timed out. Remove the clip within 30s after a successful start
- Solid red with discontinuous beeping
- Reverse polarity protection – –Reverse the clips and ensure the correct connection
- Solid red with continuous beeping
- Short circuit protection —Don’t connect the clips together or to the same metal
- Other
- Please contact support@ibuture.com with details
Important And Safety Warning
ATTENTION: Please read the following safety warning before using the product and take safety protection measures to avoid malfunctions caused by accidental operation.
Personal Safety
- Store in a cool and well-ventilated place out reach of children and pets.
- Do not place the product in high temperature environment for a long time. The operation temperature of this product is -20-60°C. The storage temperature should not exceed 50°C /122°F.
Electrical Safety
- Only start vehicles with the smart jumper cable supplied by the manufacturer.
- Do not use the product if the clamp or cable is damaged.
- Do not connect the red and black clamps together when the product is outputting.
- Do not connect the red and black clamps to the same piece of metal.
- Do not disassemble or modify this product.
- Do not use detergent to clean this product.
- Do not abuse this product and avoid heavy dropping or repeatedly hitting it.
- Do not operate the product in explosive environments such as flammable liquids, gases or dusts.
- Do not immerse the product in water.
Battery Safety
- Do not litter the product and it should be safely recycled.
- Do not incinerate the product or exposed to high temperatures, as they may explode.
- Only use replacement parts or accessories provided or recommended by manufacturer.
Warranty
- Our company provides customers with warranty of 24 months from the date of purchase.
- For assistance or warranty cover claim, please contact us:
- E-mail: support@ibuture.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>