hama 00185878 Moorea DCF Radio Wall Clock Instruction Manual

Table of Contents

Controls and Displays

The clock has the following controls and displays:

Controls and Displays

1. TIME SET =setting the local time and foreign time
+ =increases the current set value
=reduces the current set value
RC On/Off =activating/deactivating RC
RESET =restoring factory settings
LOCAL/FOREIGN slide switch =Ifyou select ‘LOCAL’, the clock displays Central European Time. If you select ‘FOREIGN’, the clock displays the desired time zone(European time +the set time zone -> ‘F’ symbol lights up)
Battery compartment
Radio symbol
Summer time
Day
Month
Day of the week
Room temperature
OFF =radio mode is deactivated

Warning

This symbol is usedtoindicate safety instruction sortodrawyour attention to specific hazards and risks.

Note

The product is intended for private, non-commercial use only.
Use the product for its intended purpose only.
Protect the product from dirt, moisture and overheating, andonlyuse it in awry environment.
Do not use the product in the immediate vicinity of heaters or other heat sources or in direct sunlight.
Do not operate the product continuously ,asities notdesigned for this.
Do not drop the product and do not expose it to animator shocks.
Do not attempt to service or repair the product yourself leave any and allservice work to qualified experts.
Do not put the product near interference fields, metal frames, computers, TVs, etc. Electronic devices and window frames can negatively affect the product’s functionality.
Do not modify the product in any way.Doing so voids the warranty.
Keep the packaging material out of the reach of children due to the risk of suffocation.
Dispose of packaging material immediately according to locally applicable regulations.
Do not operate the product outside the power limits given in the specifications.
Do not open the device or continue to operate it if it becomes damaged.
Keep this product, as allelectrical products, out of the reach of children!
Use the item only in moderate climatic conditions.

Warning–Batteries

When inserting batteries, note the correct polarity(+and -markings)and insert the batteries accordingly. Failuretodosocould result in the batteries leaking or exploding.
Only use batteries thatmatch the specified type. Keep the instructions for the correct choice of batteries included with the operating instructions of devices safe for future reference.
Before you insert the batteries, clean the battery contacts and the polarity contacts.
Do not allow children to change batteries without supervision.
Replace all the batteries in aset at the same time.
Do not mix old and new batteries, or batteries of different types or from different manufacturers.
Remove the batteries from products that are not being used for an extended period (unless these are being kept ready for an emergency).
Do not short-circuit batteries.
Do not charge batteries.
Do not burn batteries or heat them up.
Never open, damage or swallow batteries or allow them to enter the environment. They can contain toxic, environmentally harmful heavy metals.
Remove spent batteries from the product and dispose of them without delay.
Avoid storing, charging and using in extreme temperatures and at extremely low atmospheric pressures (suchasathigh altitudes).
Ensure that batteries with damaged housings do not come into contact with water. |
Keep batteries out of the reach of children.

Open the battery compartment (7)and insert two AA batteries with the correct polarity into the battery compartment.
Close the battery compartment.
If the display remains blank after inserting anew battery, change the batteries or press the RESET button (5)on the back of the clock using appointed object.

Replacing the battery

Open the battery compartment on the back of the product.
Remove and dispose of any used batteries. Insert the new battery (AA).Ensure that the polarity of the battery corresponds to the symbols in the battery compartment.
Close the battery compartment.

Before mounting the clock, ensure that the chosen Wallis suitable for the weight to be mounted, and make sure that there are no electrical wires, water, gas or other lines at the installation sixteenth wall.
Purchase special fastening materials from specialized dealers.
Do not mount the product above locations where persons might linger.

Automatic date/time setting using the DC signal

Once the battery is insertedproperly,the clockwillautomatically be set to 12:00 pm and its reception willbeactivated. As soon as the DC signal was received and processed (approx. 3minutes up to amaximumof15minutes), the correct time is displayed automatically.
Do not move the clock during this process.
If the clock has not correctly set itself after15 minutes, thereisaproblem with the reception or with the selected location. Repeat the setting process at another location. First, remove the batteries for about 1minute and then insert them again with the correct polarity.
If ,during initial setup of the device, radio signal is notreceived within the minutes, the search is aborted. The radio icon will go out.
Ifthereare reception problems, we recommend leaving the clock to sit overnight, since interference is generally less at night.
In the meantime, you can start search for the DCF radio another location or you can manually set and date.
The clock automatically continues to search for the signal on basis. If thesignalisreceivedsuccessfully,the manually-set time and date are overwritten.

Hama GmbH &CoKGassumes no liability and provides no warranty for damage resulting from improper installation/mounting, improper useofthe productorfrom failuretoobserve the operating instructions and/or safety notes.

Hereby, Hama GmbH &CoK Gdeclares that the radio equipment type [00185878] is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://uk.hama.com 00185878 Downloads