AIRGREAN AG-WF16L02PM 16 Inch Oscillating Wall Mount Fan Owner’s Manual

AIRGREAN AG-WF16L02PM 16 Inch Oscillating Wall Mount Fan

Product Information

• SKU: AG-WF16L02PM
• This product is a fan with various speed settings and oscillation feature.
• The fan has a polarized plug, designed to fit in a polarized outlet.
• It is recommended to read and save the instructions for safe operation.

Product Usage Instructions

Assembly

1. Unscrew the spinner clockwise or take it out from the bag.
2. Remove the plastic nut counterclockwise.
3. Fix the rear grill to the motor and tighten the plastic nut again.
4. Insert the blade into the motor shaft, ensuring that the rotor shaft pin is fitted into the groove of the blade.
5. Turn the spinner counterclockwise to tighten the blade.
6. Fix the front grill and the rear grill with circlip clip.
7. Use the fasten clip to tighten the fan grill.

Installation

Secure the supplied bracket (A) on the wall using wooden screws or plastic screws. Make sure the wider opening of the bracket is upward. Insert the hook of the wall fan into the bracket slot.

Operation

• To switch on/off the fan, adjust the desired speed by pulling the switch cord (B). The options are:
  • 0 – Off
  • 1 – Low
  • 2 – Medium
  • 3 – High
• To start and stop fan oscillation, pull the switch cord (C).
• To adjust the direction of the fan, push the guard lightly in the desired up or down direction.

Fuse Replacement

1. Grasp the plug and remove it from the receptacle.
2. Open the fuse cover by sliding it towards the blades.
3. Remove the fuse carefully by inserting a tool into the fuse slot and gradually prizing it out.
4. Replace the fuse with a 2.5 Amp, 125 Volt fuse to avoid the risk of fire.
5. Close the fuse cover by sliding it back into place.
6. Do not replace the attachment plug as it contains a safety device (fuse).

CAUTION
Read Rules for Safe Operation and Instructions Carefully.

WARNING

1. This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safely feature.
2. To reduce the risk of fire or electric shock, DO NOT use this fan with any solid- state speed control devices.

RULES FOR SAFE OPERATION

1. Never insert fingers, pencils, or any other object through the grille when fan is running.
2. Disconnect fan when moving from one location to another.
3. Disconnect fan when removing grilles for cleaning.
4. Be sure fan is on a stable surface when operating to avoid overturning.
5. Do not use fan in window. Rain may create electrical hazard.
6. Ensure that the fan is switched off from the supply mains before removing the grille.

The rules about cord and plug as below

1. This product employs overload protection (fuse). A blown fuse indicates an overload or short-circuit situation. If the fuse blows, unplug the product from the outlet. Replace the fuse as per the user servicing instructions (follow product marking for proper fuse rating) and check the products. If the replacement fuse blows, a short-circuit may be present and the product should be discarded or returned to an authorized service facility for examination and/or repair.
2. Do not operate any fan with a damaged cord or plug. Discard fan or return to an authorized service facility for examination and/or repair.
3. Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under furniture or appliances. Arrange cord away from traffic area and where it will not be tripped over.

Part Figure

GRILL & FAN BLADE ASSEMBLY

1. Unscrew the spinner clockwise (or take the spinner out from the bag) and the plastic nut counterclockwise to remove both of them. Fix the rear grill to the motor then tighten the plastic nut again. (Fig.1)
2. Insert the blade into shaft, and make sure the rotor shaft pin is fitted into groove of the blade. Turn the spinner counterclockwise to tighten the blade. (Fig.2)
3. Fix the front grill and the rear grill with circlip clip and then use the fasten clip to tighten the fan grill. (Fig.3)

OPERATING INSTRUCTION

MOUNTING ON THE WALL
Secure the supplied bracket (A) on the wall by using wooden screw or plastic screw, make sure the wider opening should be upward, insert the hook of the wall fan into the bracket slot.
SPEED ADJUSTMENT

Switch on/off the fan and Adjust to the desired speed by pulling the switch cord (B).

• 0—Off 1—Low
• 2—Medium 3—High

OSCILLATION CONTROL
Pull switch cord (C) to start and stop fan oscillation.

TO ADJUST THE WIND DIRECTION
Push the guard lightly to the desired up or down direction.

USER SERVICING INSTRUCTIONS

1. Grasp plug and remove from the receptacle or other outlet device. Do not unplug by pulling on cord.

2. Open fuse cover. Slide open fuse access cover on top of attachment plug towards blades.

3. Remove fuse carefully. Insert the tip of your tool into fuse slot (close with the terminal), then prize the fuse gradually and slowly, but not overexert. If you feel tight, you can try it at several times and prize the fuse little by little. When one side of the fuse has been prized, then you can get the fuse out entirely.

4. Risk of fire. Replace fuse only with 2.5 Amp, 125 Volt fuse.

5. Close fuse cover. Slide closed the fuse access cover on top of attachment plug.

6. Risk of fire. Do not replace attachment plug. Contains a safety device (fuse) that should not be removed. Discard product if the attachment plug is damaged.

Notice:

1. When you replace the fuse, please don’t operate suddenly or overexert, or else the product will be damage or cause accident.
2. When you feel it hard to be operated, please make sure you have got the right way.

CLEANING

1. Be sure to unplug from the electrical supply source before cleaning.
2. Plastic parts should be cleaned with mild soap and a damp cloth or sponge. Thoroughly to remove soap film with clean water.
3. Be sure not to make water or other liquid enter inside of motor.

1500 S. MILLIKEN AVE STE B.
ONTARIO, CA 91761 www.airgrean.com

References

• Home - Airgrean

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>