EUREKA ERGONOMIC ERK-ED-I47-OG-US Two Drawer Electric Standing Desk Instruction Manual

EUREKA ERGONOMIC ERK-ED-I47-OG-US Two Drawer Electric Standing Desk

Product Information

Specifications

• Model: ERK-ED-I47-OG-US / ERK-ED-I47-WN-US
• Model: ERK-ED-I55-OG-US / ERK-ED-I55-WN-US

Product Usage Instructions

Step 1: Assembly

1. Attach X2 to (P1) X1
2. Attach #1 P1 to (P2)

Step 2: Attach Components

1. Attach X8 to (B) X1
2. Attach (J) to P1 and P2

Step 3: Attach More Components

1. Attach X2 to (P3) X4
2. Attach X4 to (B) X4
3. Attach (C) to B
4. Attach (J) to C
5. Attach (K) to C

Step 4: Attach Remaining Components

1. Attach X2 to (P4) X4
2. Attach X8 to (P25) X8
3. Attach (A) to (J)
4. Attach P4 and P25 to #1, P3, B, and C

Step 5: Additional Attachments

1. Attach (I)

Step 6: Attach (P5) X19, (F), and (L)

1. Attach (P5)
2. Attach (L) to #1 P5

Step 7: Attach (P8) X1 L, (P9) X1 R, (P10) X1 L, and (P11) X4 L

1. Attach (P8) X1 L to P10
2. Attach (P9) X1 R to P8 and P11

Step 8: Tighten Components

1. Tighten (P6) L to #1 and #2
2. Tighten (L) X2 to P8 and P6
3. Tighten P9 and P11 to P10

Step 9: Tighten Components (Continued)

1. Tighten (P7) R to #1 and (G) X2 #2
2. Tighten P9 and P7 to P11

Step 10: Attach (G) X1 L to #1 and #2

1. Attach (G) X1 L to P15

Step 11: Tighten Components (Continued)

1. Tighten (L) X1 L to #1 and #2

Step 12: Attach (P12) X1 L, (P13) X1 R, and (P14)

1. Attach (P12) X1 L to P13
2. Attach (P14) R to #1 P14

Step 13: Tighten Components (Continued)

1. Tighten (L) X1 L to #1 and #2

Step 14: Attach (C) X1 and (K)

1. Attach (C) X1 to P22
2. Attach (K) to P22

Step 15: Attach (P22) X4 and (D) X1

1. Attach (P22) X4 to (D)

Step 16: Attach (P24) X1 and (P33)

1. Attach (P24) X1 to P33

Step 17: Attach (P23) X4, (C) X1, and (K)

1. Attach (P23) X4 to (C)
2. Attach (K) to P23

Step 18: Attach (P28) X5, (P29) X5, and (P30)

1. Attach (P28) X5 to (P29) X5
2. Stick (P30) Paste to #1 and #2
3. Tighten! (P30) Tighten! Apretar!

Step 19: Attach (P16) X1 L, (P17) R, and (P18) X4

1. Attach (P16) X1 L to P18
2. Attach (P17) R to P16

Step 20: Attach (P19)

1. Attach (P19) to P18 and P17

Step 21: Attach (P15) X1, (F) X4, and (L) X1

1. Attach (P15) X1 to (F) X4
2. Attach (L) X1 to #1

Step 22: Tighten Components (Continued)

1. Tighten (G) X4 to #1 and #2

Step 23: Attach (P26) X1, (P27) X6, and (E)

1. Attach (P26) X1 to (P27) X6
2. Attach (L) to (E)

Step 24: Attach (P20) X4, (F) X1, and (L)

1. Attach (P20) X4 to (F) X1
2. Attach (L) to #1 P26

Step 25: Attach (P21) X4, (G) X1, and (L)

1. Attach (P21) X4 to (G) X1
2. Tighten P21 to P21

Step 26: Attach (P31)

1. Attach (P31) to #1 and #2

Step 27: Operating Instructions

Adjust the Height:

• Press ▲ to make the desk go upward until it reaches the highest point.
• Press ▼ to make the desk go downward until it reaches the lowest point.
• Briefly press ▲ or ▼ make the desk go a small distance correspondingly.

Set Memory Heights:

• To set the height, follow these steps:
  1. Adjust the desktop to the desired height.
  2. Press 1 or 2 for 4 seconds until S-1 or S-2 flashes.
• To inquire about memory height, briefly press 1 or 2, and the corresponding memory height will flash.
• To adjust the desk to the memory height, double-press 1 or 2 and the desktop will automatically move to the corresponding memory height.
• Pressing any button will stop the process.

Set the Minimum Height:

• To set the minimum height, follow these steps:

1. Adjust the desk to the desired height.
2. Press 2 and ▲ for 5 seconds until the display shows – do.

• To remove the saved minimum height:

1. Method 1: Refer to the Initial Setup procedure.
2. Method 2: Adjust the desk to the minimum height. Press ▼ 2 for 5 seconds until the display shows – do.

FAQ (Frequently Asked Questions)

Q: How many memory heights can be saved?

• A : Two memory heights can be saved.

Q: Can I adjust the desk to a small distance?

• A : Yes, you can briefly press ▲ or ▼ make the desk go a small distance correspondingly

PARTS

HARDWARE

ASSEMBLY INSTRUCTIONS

• STEP 1
• STEP 2
• STEP 3
• STEP 4
• STEP 5
• STEP 6
• STEP 7
• STEP 8
• STEP 9
• STEP 10
• STEP 11
• STEP 12
• STEP 13
• STEP 14
• STEP 15
• STEP 16
• STEP 17
• STEP 18
• STEP 19
• STEP 20
• STEP 21
• STEP 22
• STEP 23
• STEP 24
• STEP 25
• STEP 26
• STEP 27
• STEP 28
• STEP 29
• STEP 30

OPERATING INSTRUCTIONS

Adjust the Height

• When you press “∧”, the desk goes upward until it reaches the highest point. When you press “∨”, the desk goes downward until it reaches the lowest point. When you press “∧” or “∨” briefly, the desk goes a small distance correspondingly.

Set Memory Heights

• Set the height: 2 memory heights can be saved as follows.

1. Adjust the desktop to the desired height.
2. Press “1” or “2” for 4 seconds until “S-1” or “S-2” flashes.
   • Memory height inquiry: press “1” or “2” briefly and the corresponding memory height will flash. Adjust the desk to the memory height: double-press “1” or “2” and the desktop will automatically move to the corresponding memory height. Pressing any button will stop the process.

Set the Minimum Height

Set the minimum height: the minimum height of the desk can be set to avoid collision. If the desktop reaches the minimum height, the display will show “- L o”. The procedure is as follows.

1. Adjust the desk to the desired height.
2. Press “2” and “∨” for 5 seconds until the display shows “- d o”.

Remove the saved minimum height:

• Method 1: refer to the Initial Setup procedure.
  Method 2 : Adjust the desk to the minimum height. Press “∨” and “2” for 5 seconds until the display shows “- d o”.

Set the Maximum Height

Set the maximum height: the maximum height of the desk can be set to avoid collision. If the desktop reaches the maximum height, the display will show “- H I”. The procedure is as follows.

1. Adjust the desk to the desired height.
2. Press “∧” and “1” for 5 seconds until the display shows “– up”.

Remove the saved maximum height:

• Method 1: refer to the Initial Setup procedure.
• Method 2: a. Adjust the desk to the maximum height. b. Press “∧” and “1” for 5 seconds until the display shows “– up”.

Initial Setup

• (Perform this procedure in normal operation, or when the control box is replaced for the first time)
• Press “∧” and “∨” at the same time until the display flashes “- – -”. The system will enter the initialization mode and the desk will automatically move up and down. Once the desk stops, the initial setup process is complete.

Factory Reset

• (Perform this procedure when the error code “E12”, “E16” or “rST” occurs)
• Press “∨” for 5 seconds until the display flashes “- – -” and the system will enter the reset mode. The desk will automatically move to its lowest height regardless of the previously set height limits and then rise to a pre-programmed height.
• Once the desk stops, the reset process is complete.

ERROR CODES AND TROUBLESHOOTING

or “∨” again. If the code still exists, please check whether the leg cables are loose.

2. If the code still exists after step 1, please switch the leg cables. If the code does not change, the control box is faulty. If the code changes (eg: E01 -> E02 or E02 -> E01), the leg is faulty. Please contact our local customer service team for replacement parts.

E03、E04| Overload or motor failure| Please switch the leg cables. If the code does not change, the control box is faulty. If the code changes (eg: E03 -> E04 or E04 -> E03), the leg is faulty. Please contact our local customer service team for replacement parts.
E05、E06| Faulty leg sensor| 1. Press “∧” or “∨” again. If the code still exists, please check whether the leg cables are loose.

2. If the code still exists after step 1, please switch the leg cables. If the code does not change, the control box is faulty. If the code changes (eg: E05 -> E06 or E06 -> E05), the leg is faulty. Please contact our local customer service team for replacement parts.

E07| Faulty power supply of the control box| Unplug the desk and plug it back in after 10 seconds. If the code still exists, the control box is faulty. Please contact our local customer service team for replacement parts.
E08、E09| Faulty leg| Unplug the desk and plug it back in after 10 seconds. If the code still exists, the control box is faulty. Please contact our local customer service team for replacement parts.
E10、E11| Faulty control box| Unplug the desk and plug it back in after 10 seconds. If the code still exists, the control box is faulty. Please contact our local customer service team for replacement parts.
E12| Faulty leg position| Factory reset: press “∨” for about 5 seconds until the display shows “- – -”.
E13| Overheat protection| Please wait for the temperature to drop before use.
E14、E15| Leg stuck| Please switch the leg cables. If the code does not change, the control box is faulty. If the code changes (eg: E14 -> E15 or E15 -> E14), the leg is faulty. Please contact our local customer service team for replacement parts.
E16| Unbalanced legs| Factory reset: press “∨” for about 5 seconds until the display shows “- – -”.
E17| Key data of the control box lost| Unplug the desk and plug it back in after 10 seconds. If the code still exists, the control box is faulty. Please contact our local customer service team for replacement parts.
r ST| The control box system suddenly turns off| Factory reset: press “∨” for about 5 seconds until the display shows “- – -”.
The display does not work after the desk is plugged in.| Faulty control box or poor electrical contact;

Faulty power supply or loose connection, etc.

| Check the power cord and whether the connection between the control box and the power supply is loose (replugging all cables is recommended). If the display still does not work properly, please contact our local customer service team for replacement parts.

DESKTOP POWER SOCKET PARAMETERS

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>