Lucci decor 259931 LEDlux Louie LED Dimmable Floor Lamp Instruction Manual

Installation Instructions
LOUIE LED FLOOR LAMP
SKU# 259931, 259932, 259933
Rated Voltage 24V 0.83A
v 1.2

Thank you for purchasing this quality Lucci product. To ensure correct function and safety, please read and follow all instructions carefully before assembly, installation, and use of this product. Please keep the instructions for future reference.

Warranty

• This fitting is covered by a 3 year warranty from the date of purchase. Please retain proof of purchase.
• Warranty will be void if there is any damage due to improper usage or modification to the product.
• Failure to comply with the instructions in this manual may increase the risk of damage or injury and will void warranty.

Installation requirements

• Select a suitable location for this light fitting:
  • Ensure it is on a flat and stable surface.
  • This product is suitable for indoor use only.
  • Do not place flammable material near or over the fitting.
  • Ensure the fitting is not installed in direct line of an air vent/system.
  • When installing a fitting in an area prone to moisture, ensure that the area is well ventilated and an appropriately rated exhaust fan is used if required. Damage or corrosion caused by moisture is not a product fault, and as such is not covered under warranty.
• Only use the supplied plug in LED driver with this fitting.
• Take care not to pull any electrical wires during unpacking as this may damage the connection.
• Lay out all the components on a smooth surface and make sure there are no components missing before assembling. If parts are missing, return the complete product to the place of purchase for inspection or replacement.
• Check whether the fitting has been damaged during transport. Do not operate/install any product which appears damaged in any way. Return the complete product to the place of purchase for inspection, repair, or replacement.
• Do not plug into the mains power socket outlet before or during assembly. Only do so after the portable lamp is fully assembled and ready to use for the first time.

Installation directions

1. Remove all packaging material from the product and be careful not to throw away accessories that may be hidden within the packaging material. If assembly is required, place the luminaire on a smooth non-scratch surface.
2. Tighten the rod (E) onto the lamp base (A), tighten the rod (D) onto the rod (E), tighten the rod (C) onto the rod (D), and tighten the rod (A) onto the rod (C).
3. Insert the plug (G) of the LED driver (I) into the socket (H).
4. Plug the LED driver (I) into the mains socket outlet and ensure it is fully plugged in.
5. Adjust the head (J) to the desired angle. Do not rotate more than 340° as this may damage the internal wires.
6. Click the switch button (B) on to turn the lamp on. Press the button repeatedly to change in the following light stages: ON(3000K)→ON(4000K)→ON(5000K)→OFF→ON (3000K). Press and hold the switch button (F) to increase the brightness, Press and hold the switch again to decrease the brightness.
   NOTE: This fitting has a memory function which allows it to retain the last used light stage when turned off then turned back on.
   NOTE: To reset the fitting to its original light stage, unplug the LED driver (I). After 5 seconds, plug the LED driver (I) back into the mains socket again and click the switch button (B) on. The fitting will be reset to ON (3000K).
   NOTE: When adjusting the head (J), do not adjust more than 340° as this may damage the internal wires.

Safety Tips

• Always ensure the power is OFF and the luminaire has cooled down before performing any maintenance, cleaning, changing the globe, or making any adjustments to the luminaire.
• The external flexible cable or cord of this luminaire cannot be replaced; if the cable or cord is damaged, the luminaire shall be destroyed.
• To avoid injury or damage to the luminaire, ensure that power leads and screws are secure before connecting the power.
• Young children should be supervised to ensure that they do not play with the portable lamp.
• Handle the luminaire and/or shade with care to avoid any damage or breakage.
• Select a suitable location away from liquids and hazards.
• To clean, wipe with a soft damp cloth. Do NOT soak or immerse the product in water or other liquids.
• Ensure that the luminaire does not come in contact with corrosive chemicals/solvents or abrasive cleaners etc.

Specifications

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>