ONKYO HTP-693 5.1.2ch Home Theater Speaker User Guide

HTP-693 5.1.2ch Home Theater Speake

5.1.2ch Home Theate r Speaker Package

Supplied Accessories

Mak sure you have the following accessories.
Front & Height Speakers(SKF-693) Center Speaker (SKC- 591N)
“1 Configuration of the rubber stoppers may be different from the figure, such as being 2 sheets instead of 1 sheet. but the total number will be same.

Surround Speakers (SKR-590 )
Powered Subwoofer (SKW-593)

Parts Names

Front & Height Speakers (SKF-693)
Center Speaker (SKC-591N)
Surround Speakers (SKR-590) Caution
The front grilles are not designed to be removed so do not attempt to remove them forcibly, as this will damage them.
Powered Subwoofer (SKW-593)
Front
— Status indicator
Off: Subwoofer in standby mode or disconnected from power source
Blue:Subwoofer on
The status indicator lights blue when low frequency sound is being passed through the speaker.
The indicator does not light in the normal dialog or high frequency sound.
Note

• The indicator does not indicate that power supply of the subwoofer has turned on.
  With the Auto Standby function, the SKW-593 automatically turns on when an input signal is detected in standby mode. When there’s no input signal for a while, the SKW-593 automatically enters standby mode.
  Rear
  Note
  The Auto Standby function turns the subwoofer on when the input signal exceeds a certain level. If the Auto Standby function does not work reliably, try slightly increasing or decreasing the subwoofer output level on your receiver.

Before Using the Home Theater Speaker Package

Using the Rubber Stoppers for a More Stable Platform
We recommend using the supplied rubber stoppers to achieve the best possible sound from your speakers. The rubber stoppers prevent the speakers trom moving, then provide a more stable platform. Use rubber stoppers for the center speaker.
Using the Floor Pads for Subwoofer
If the subwoofer is placed on a hard floor (wood, vinyl, tile, etc.) and playback is very loud, the subwooter’s feet may damage the flooring. To prevent this, place the supplied pads underneath the subwoofer’s feet. The pads also provide a stable base for the subwoofer.
Setting the Subwoofer Level

To set the level of the subwoofer, use the OUTPUT LEVEL control. Set it so that bass sounds are evenly balanced with the treble sounds from the other speakers. Because our ears are less sensitive to very low bass sounds, there’s a temptation to set the level of the subwoofer too high. As a rule of thumb, set the subwoofer level to what you think is the optimal level. and then back it off slightly.
Wall Mounting
To mount the front‘surround speakers vertically, use the keyhole slot shown to hang each speaker on a screw that’s securely screwed into the wall.
To mount the center speaker horizontally, use the two keyhole slots shown to hang the speaker on two screws that are securely screwed into the wall. Tip

• If the center speaker is tilted, loosen the screw on the declined side to move upward so that the speaker could be adjusted vertically.

CAUTION

• A mounting screw’s ability to support a speaker depends on how well it’s anchored to the wall. If you have hollow walls, screw each mounting screw into a stud. If there are no studs, or the walls are solid, use suitable wall anchors. Use screws with a head diameter of 5/16″ (8 mm) or less and a shank diameter of 1’8″ (4 mm) or less. With hollow walls, use a cable’pipe detector to check for any power cables or water pipes before making any holes.

• Leave a gap of between 3/16″ (5 mm) and 7/16″ (10 mm) between the wall and the base of the screw head, as shown (We recommend that you consult a home installation professional).

Enjoying Home Theater

The Home Theater means that you can enjoy surround sound with a real sense of movement in your own home — just like being in a movie theater or concert hall.
Front & Height speakers (SKF-693)

1. These speakers placed with their top diaphragms facing toward the ceiling can produce a sound field of the Dolby Atmos listening mode by providing sounds echoing off the ceiling. The speakers on the front output front stereo sound.

2. Center speaker (SKC-591N)
   This speaker outputs center sounds such as dialogs  and vocals.

3. Surround speakers (SKR-590)
   These speakers create back sound field.

4. Subwoofer (SKW-593)
   The subwooter reproduces bass sounds and creates rich sound field.

• Refer to the operating instructions for your AV receiver and other equipment for details about the placement of the speakers.

Connecting the Speakers

Speaker Connection Precautions
Read the following before connecting your speakers:

• Turn off your receiver before making any connections.

• Pay close attention to speaker wiring polarity.
  Connect positive (-) terminals to only positive (+) terminals, and negative (—) terminals to only negative (—) terminals. If the speakers are wired incorrectly, the sound will be out of phase and will sound unnatural.

• Be careful not to short the positive and negative wires. Doing so may damage your amplifier.

• Using the supplied RCA cable. connect the subwoofer’s LINE INPUT to your AV receiver’s SUBWOOFER jack.

Specifications

MFront & Height Speakers (SKF-693)

Dimensions (W H « D)| 155 mm « 467 mm * 183 mm 6-1/8″ x 18-3/8″ x 7-3/ 16″ (incl. grille and projection)
---|---
Weight| 3.6 kg (7.9 Ibs.)
Keyhole slot| Available
Grille| Fixed
Front Unit|
Type| 2 Way Bass-Reflex
Impedance| 6Ω
Maximum input power| 130 W
Sensitivity| 84.5 dB’W’m
Frequency response| 55 Hz to 50 kHz
Crossover frequency| 4 kHz
Cabinet capacity| 5.7 L (0.20 cubic feet)
Drivers unit| 12 cm (5″) Cone Wooter x 1  2.5 cm (1″) Balanced Dome x 1
Terminal| Spring type color coded
Other| Non-magnetic shielding
Height Unit|
Type| Full Range Closed Box
Impedance| 6Ω
Maximum input power| 130 W
Sensitivity| 81 dB/Wi’m
Frequency response| 80 Hz to 20 kHz
Cabinet capacity| 1.0 L (0.036 cubic feet)
Drivers unit| 8 cm (3-1’4″) Cone Speaker
Terminal| Spring type color coded
Other| Non-magnetic shielding

Center Speaker (SKC-591N)

16″ 4-12″ 4-1 1/16″(incl. grille and projection)
Weight| 2.3 kg (5.1 Ibs.)
Drivers unit| 8 cm (3-1/4″) Cone Woofer x 2
2.5 cm (1″) Balanced Dome x |
Terminal| Spring type color coded
Keyhole slot| Available
Grille| Fixed
Other| Non-magnetic shielding

Surround Speakers (SKR-590)

(incl. grille and projection)
Weight| 1.0 kg (2.2 Ibs.)
Drivers unit| 8 cm (3-1/4″) Cone Speaker x 1
Terminal| Spring type color coded
Keyhole slot| Available
Grille| Fixed
Other| Non-magnetic shielding

Powered Subwoofer (SKW-593)

at 100 Hz witha maximum total harmonic distortion of 1%
Frequency response| 25 Hz to 150 Hz
Cabinet capacity| 38 L (1.34 cubic feet)
Dimensions (W < H x D)| 317.5 mm =< 463 mm x 398 mm 12-1/2″ x 18-1/4″ « 15-11/16″ (incl. projection)
Weight| 9.6 kg (21.2 Ibs.)
Audio input| 1 (RCA analog mono)
Drivers unit| 25 cm (10″) Cone Wooter x 1
Power supply| AC 120 V, 60 Hz
Power consumption| 35 W
Other| Auto Standby function Non-magnetic shielding

Specifications and appearance are subject to change  without prior notice.
Note
For non-magnetic shielded speakers:
Try moving the speakers away from your TV or monitor. If discoloration should occur, turn off your TV or monitor, wait 15 to 30 minutes, and then turn it back on again. This normally activates the degaussing function, which neutralizes the magnetic field, thereby removing any discoloration effects.

SN 29402327
(C) Copyright 2016 Onkyo & Pioneer
Corporation Japan. All rights
teserved.

Documents / Resources

| ONKYO HTP-693 5.1.2ch Home Theater Speaker [pdf] User Guide
HTP-693 5.1.2ch Home Theater Speaker, HTP-693, 5.1.2ch Home Theater Speaker, Home Theater Speaker, Theater Speaker, Speaker
---|---

References

• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>